KRT720001 EN
Copyright © 2016 VARO P a g e | 1 www.varo.com
1 APPLICATION ................................................................. 2
2 DESCRIPTION FIG. A ..................................................... 2
3 PACKAGE CONTENT LIST ............................................ 2
4 SYMBOLS ........................................................................ 3
5 GENERAL SAFETY WARNINGS .................................... 3
6 ADDITIONAL SAFETY INSTRUCTIONS FOR
BATTERIES ....................................................................................... 3
7 USE ................................................................................... 4
7.1 To Install Batteries (Fig.1) ................................................................................4
7.2 To Attach Flexible Tube with Handle (Fig. 2) ..................................................4
7.3 To Install Accessories .....................................................................................4
7.4 Video Output ....................................................................................................4
7.5 Switch on Camera ............................................................................................4
7.6 Mirror Image .....................................................................................................4
7.7 LEDs Brightness Control .................................................................................4
7.8 LCD Contrast Control ......................................................................................5
8 MAINTENANCE AND STORAGE ................................... 5
9 TECHNICAL DATA .......................................................... 5
10 SERVICE .......................................................................... 5
11 ENVIRONMENT ............................................................... 6
12 DECLARATION OF CONFORMITY ................................ 7
KRT720001 EN
Copyright © 2016 VARO P a g e | 2 www.varo.com
INSPECTION CAMERA
KRT720001
1 APPLICATION
The inspection video camera can be used for easy surveying of small, hard-to-
reach places.
WARNING! Read this manual and general safety
instructions carefully before using the appliance, for your
own safety. Your power tool should only be passed on
together with these instructions.
2 DESCRIPTION FIG. A
1. Power switch
2. Rotate/mirror image
3. Brightness
4. Contrast
5. Power indicator
6. Color TFT-LCD monitor
7. Mini waterproof LED lens
8. Flexible tube interface
9. Flexible tube
10. Video output
11. Handle
12. Magnet
13. Mirror
14. Single hook
15. Double hook
16. Rubber accessories
holder
17. Video cable
3 PACKAGE CONTENT LIST
Remove all packing materials
Remove remaining packaging and transit supports (if existing)
Check the completeness of the packing content
Check the appliance, the power cord, the power plug and all accessories
for transportation damages.
Keep the packaging materials as far as possible till the end of the warranty
period. Dispose it into your local waste disposal system afterwards.
WARNING Packing materials are no toys! Children must
not play with plastic bags! Danger of suffocation!
1 x handle with LCD screen
1 x flexible tube video interface
with lens
1 x video cable
1 x double hook
1 x single hook
1 x magnet
1 x mirror
1 x rubber accessories holder
KRT720001 EN
Copyright © 2016 VARO P a g e | 3 www.varo.com
When parts are missing or damaged, please contact your
dealer.
4 SYMBOLS
In this manual and/or on the machine the following symbols are used:
Warning / Danger
In accordance with
essential requirements
of the European
directive(s)
Read manual before usage
5 GENERAL SAFETY WARNINGS
Prevent object and liquid entry. Never spill liquid of any kind on the video
display unit. Liquid increases the risk of electrical shock and damage to
the product.
The unit is not shock-resistant. Do not use power tool as a hammer and
avoid high impact resultant from things such as dropping the unit from
height.
Do not immerse camera handle or LCD screen in water. Avoid moisture,
and store product in a dry place. Such measures reduce the risk of electric
shock and damage. The lens and the tube are water resistant when the
unit is fully assembled, but the LCD screen and handle are not.
Do not use the camera if condensation forms inside the lens. Let the water
evaporate before using again.
Turn off the system if it is not in use.
6 ADDITIONAL SAFETY INSTRUCTIONS FOR
BATTERIES
When replacing batteries, always replace the complete set. Do not mix old
batteries with new ones.
Prevent removed batteries from short circuiting.
Do not store batteries where the temperature may rise above 50 °C, e.g. in
a car which has been parked in the sun.
Do not burn batteries.
Never attempt to open batteries.
In case of battery leakage, carefully remove the liquid using a cloth. Avoid
skin or eye contact. Do not swallow. In case of skin or eye contact, rinse
abundantly for 10 minutes with clean water and consult a physician.
KRT720001 EN
Copyright © 2016 VARO P a g e | 4 www.varo.com
7 USE
7.1 To Install Batteries (Fig.1)
1. Remove battery cover.
2. Insert four (4) AA batteries into their appropriate slots, with proper
orientation, as indicated on the battery compartment.
3. Replace battery cover.
7.2 To Attach Flexible Tube with Handle (Fig. 2)
To connect the flexible tube camera with control handle, first make sure that the
keyed end of the tube is aligned with the slot in the handle, then use slight force
to push them together. Once properly aligned, twist the treaded knob clockwise
until the connection is securely in place.
a. Keyed end plugs into socket.
b. Fasten the treaded knob.
7.3 To Install Accessories
The three (3) included accessories (mirror, hook and magnet) are all attached to
the camera in the same way as illustrated on Fig. 3.
a. Hook the rear end of the accessory into the hole.
b. Wear the rubber ring with the sleeve.
7.4 Video Output
Insert video cable into the video out socket of the monitor, insert the other end
of the cable into the video in jack of any compatible TV or display device. The
LCD monitor is now capable of outputting high quality video to another display.
7.5 Switch on Camera
1. Press and hold on the power switch for about 3 seconds to turn on
the camera, the power indicator will illuminate and the LCD will
become viewable (Fig. 4).
2. When in use, the tube should easily maneuver itself into position.
Do not apply excessive force.
3. The flexible tube can be bent into numerous shapes that may help
you explore areas you otherwise thought were impossible to see.
4. The accessories included can be used to retrieve small items like
dropped rings or screws.
7.6 Mirror Image
In real-time monitoring mode, the mirror image can be adjusted by pressing the
‘rotate/mirror image’ button 2 (Fig. 5).
7.7 LEDs Brightness Control
The 8 levels of LED brightness can be adjusted by pressing the brightness
button in real-time monitoring (Fig. 6).
KRT720001 EN
Copyright © 2016 VARO P a g e | 5 www.varo.com
7.8 LCD Contrast Control
The 8 levels of LCD contrast can be adjusted by pressing the contrast button in
real-time monitoring (Fig. 7).
8 MAINTENANCE AND STORAGE
Keep the measuring tool clean and dry at all times to ensure proper and
safe working.
Wipe off debris using a moist and soft cloth. Do not use any cleaning
agents or solvents.
9 TECHNICAL DATA
Type
KRT720001
Screen size
2.31” TFT LCD
Contrast
300
Brightness
220CD/M² (TYP)
Batteries
4x AA (1.5V x 4)
Work time
6 hours (max.)
Consumption current
238mA
Output signal impedance
75ohm
Output signal level
0.9—1.3Vp-p
Imaging sensor
1/9-inch CMOS
Effective pixels
640 x 480
Video system
PAL/NTSC
Horizontal viewing angle
48°
Minimum illumination
0 Lux (LED ON)
Waterproof capacity
IP67 (for lens/tube only)
Dimensions of tube
Ø8mm x 980mm (including camera)
Dimensions of handle
257 x 92 x 44mm (excluding flexible
tube)
Operating temperature
-10°C~50°C
Operating humidity
15~85%RH
Approx. weight
407g (including batteries)
10 SERVICE
Repairs may only be carried out by an authorized customer service centre
for KREATOR tools.
You can always obtain more information at the number 00 32 3 292 92 90.
KRT720001 EN
Copyright © 2016 VARO P a g e | 6 www.varo.com
Any transportation costs shall always be borne by the customer, unless
agreed otherwise in writing.
Your purchase receipt must be kept as proof of date of purchase.
11 ENVIRONMENT
Should your appliance need replacement after extended use,
do not discard it with the household rubbish but dispose of it in
an environmentally safe way.
Waste produced by electrical machine items should not be
handled like normal household rubbish. Please recycle where
recycle facilities exist. Check with your Local Authority or
retailer for recycling advice.
KRT720001 EN
Copyright © 2016 VARO P a g e | 7 www.varo.com
12 DECLARATION OF CONFORMITY
VARO N.V. - Joseph Van Instraat 9 - BE2500 Lier - BELGIUM, declares
that,
Product: Inspection camera
Trade mark: KREATOR
Model: KRT720001
is in conformity with the essential requirements and other relevant provisions of
the applicable European Directives, based on the application of European
harmonized standards. Any unauthorized modification of the apparatus voids
this declaration.
European Directives (including, if applicable, their amendments);
2011/65/EU
2014/30/EU
European harmonized standards (including, if applicable, their amendments);
EN55022 : 2010
EN55024 : 2010
Keeper of the Technical Documentation : Philippe Vankerkhove, VARO – Vic.
Van Rompuy N.V.
The undersigned acts on behalf of the company CEO,
Philippe Vankerkhove
Regulatory Affairs – Compliance Manager
Date: 19/04/2016
/