Accuride T46322G14 Specification

Category
Wall & ceiling mounts accessories
Type
Specification

This manual is also suitable for

BRACKET CONVERSION KIT
Part Number 4180-0431-XE
For Use With Slide Model 3732
APPLICATIONS: Converts 3732 slides for face frame
applications. Rear bracket easily snaps on the existing
slide. No tools needed for installation of bracket to slides.
See Model 3732 data sheet for additional slide details.
Attach Rear Brackets to Slide Member
First, separate slide members by depressing lever into the
drawer member.
ACCURIDE INTERNATIONAL INC.
12311 Shoemaker Avenue
Santa Fe Springs, CA 90670
TEL (562) 903-0200
FAX (562) 903-0208
www.accuride.com
Manufacturing, Engineering, and Sales
United States • Germany • Japan • Mexico • United Kingdom
Installation Instructions
Copyright © 2002 Accuride International Inc. Printed in U.S.A. 3700-1084(9449)-MK571-R1-0302
Mount Slide to Drawer
1. Install drawer member using vertical slots.
2. Insert drawer member after making sure ball bearing
retainers are fully forward. Close drawer completely.
3. Adjust vertical position and install two more screws in
round holes after free movement is achieved. See
Figure 3.
Mount Slide to Cabinet
1. Secure a .75" thick X 2" wide vertical mounting strip to
the rear wall or cabinet back for each slide.
2. Position the front of the slide against the front vertical
mounting strip. Install screw in the first mounting hole.
Do not tighten screw completely at this time.
3. Extend the rear bracket until it contacts the rear
vertical mounting strip. Check that both cabinet members
are vertically and horizontally parallel. Mount the rear
bracket using the two vertical slots. Make any necessary
adjustment. See Figure 2.
4. Secure the rear bracket with a screw in a round hole.
Tighten the screw in the front to secure the slide. See
Figure 2.
Attach Rear Bracket
1. Push rear bracket onto the slide cabinet member.
Ensure locking lug on plastic slider engages the mating
hole in the slide member and the bumper on the slide
seats into the plastic slider on the bracket. See Figure 1.
Rear brackets can be ordered as a kit or in bulk. Mounting
screws are not included.
For rear bracket kit, order part number 4180-0431-XE.
Each kit contains 2 rear brackets and installation sheet.
Order one kit part per pair of slides.
For bulk, order 2 rear brackets, part number 4080-0234-CE,
per pair of slides ordered.
Ordering and Packaging Procedure
Copyright © 2002 Accuride International Inc. Printed in U.S.A. 3700-9449(1084)-MK088-R1-0302
.170 DIA.
[4.3] (7X)
Figure 2
Rear
Brackets
Figure 1
Rear Bracket
Bumper
Slide
Cabinet
Member
Plastic
Slider
Rear Bracket
.88
[22.2]
.25
[6.4]
.175 X .315
[4.4 X 8.0]
(2X)
1.25
[31.8]
.63
[15.9]
.50
[12.7] 1.00
[25.4]
1.49
[37.8]
.180 X .580
[4.6 X 14.7]
.79
[20.1]
.21
[5.3]
Figure 3
Mounting Strip
Face Frame
Disconnect Lever
Drawer Member
Set Back
1-1/4”
[31.8]
7/16”
[11.1]
3/16"
[4.8]
Note: Specification, materials, prices, terms, and delivery
are subject to change without notice.
.31
[8.0]
®
  • Page 1 1

Accuride T46322G14 Specification

Category
Wall & ceiling mounts accessories
Type
Specification
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI