Mark DecoPAR DPR36 Quick start guide

Brand: Mark

Model: DecoPAR DPR36

Category: Motorcycle Accessories

Type: Quick start guide

Model No: DPR36 and DPR3612

TECHNICAL SPECIFICATIONS

Power Supply: 120V ~ 50-60Hz

Power consumption: 36 W

Dimensions (LxWxH): 150 x 180 x 200mm / 6 x 7 x 7.9 in.

Weight (unpacked): 1.4 kg / 3.1 lb.

Fitting lamp: 6V or 12V 30W PAR36 or AR111 Halogen lamp

Max. ambient temp. Ta: 25°C / 77°F

Max. housing temp. Ts: 90°C / 194°F

Min. distance: 0.5 m / 1.6 ft.

Manufacturer

Lamp Code

Watts Volts

Candlepower

(Candela)

Color

Temp (°K)

Field Angle

(Degrees°)

Rated Life

(Hours)

DecoPAR36 12 Volt Lamp Types

35AR111/SSP4

35AR111/SP8

35AR111/FL25

50AR111/SSP4

50AR111/SP8

50AR111/FL25

75AR111/SP4

75AR111/FL25

75AR111/WFL45

50PAR36/H/SP5

50PAR36/H/SP8

50PAR36/H/FL30

40,000

14,000

2,500

45,000

20,000

4,000

30,000

5,300

2,000

35,000

30,000

1,300

3,000

4,000

4°

8°

25°

4°

8°

25°

4°

25°

45°

5°

8°

30°

3,000

3,050

It is suggested that a glass shield be used with AR111 type lamps.

Manufacturer

Lamp Code

Watts Volts

Candlepower

(Candela)

Color

Temp (°K)

Field Angle

(Degrees°)

Rated Life

(Hours)

DecoPAR36 6 Volt Lamp Types

35AR111/SSP4/6V

4515

6.4

30,000

55,000

3,000

4°

5°

3,000

100

PAR 36 fixture with integral 6 or 12 Volt magnetic

transformer for pin spot or AR111 lamps.

OPERATION:

Installation with Clamp

Select an appropriate clamp from your dealer to attach the fixture to a mounting pipe

(e.g. truss system) and adjust the position of the fixture once it is mounted (Figure 2).

1. Tightly fasten the clamp to the yoke with the provided

yoke bolt and lock washer.

2. Place the clamp on mounting pipe; tighten the pipe bolt

to secure it.

3. Loosen the clamp pan screw and rotate the yoke to the

desired position.

4. Tighten the pan screw to lock the fixture into position.

5. Adjust the desired inclination-angle via the yoke and

fix the yoke locking knob.

6. Always use appropriate safety cable.

Model No: DPR36 and DPR3612

IMPORTANT SAFETY INSTRUCTIONS

1. Prior to initial start-up, make sure that there is no shipping damage. Should there

be any, consult your dealer and do not use the device.

2. CAUTION! High voltage can inflict dangerous electric shock when touching

uninsulated wires! Keep away from heaters and other heating sources!

3. Do not mount the device on or near combustible surfaces.

4. Always install the device with the color frame retaining clip in the locked position.

5. This device falls under protection-class I, therefore it is essential that the yellow/green

conductor get connected to ground. The electric connection must be carried out by

a qualified person.

6. Make sure that the power cord is not crimped or damaged by sharp edges.

Periodically inspect the device and the power cord for damage.

8. If the external flexible cable or cord of this luminaire is damaged, must be exclusively

replaced by a qualified dealer.

9. Never let the power cord come into contact with other cables! Handle the power

cord and all connections with the mains with particular caution!

10. Always disconnect from the mains when the device is not in use or before cleaning

it. Only handle the power cord by the plug. Never pull out the plug by tugging the

power cord.

11. During the initial startup some smoke or odor may arise. This is a normal process

due to new paint and materials and does not necessarily mean that the device is

defective.

12. DANGER OF BURNS! Never touch the device during operation! The housing

heats up to max. temperature (Ts) of 90°C / 194°F.

13. Do not switch the device on and off in short intervals as this will reduce the life span

of the lamp.

14. HEALTH HAZARD! Never look directly into the light source. Sensitive persons may

suffer an epileptic shock.

15. Children and inexperienced personnel should not operate this device.

16. There are no end-user serviceable parts inside the device. Maintenance and service

operations are only to be carried out by a qualified dealer.

Installing / Connection with the Mains

1. ELECTRICAL SHOCK HAZARD! The electric connection must only be carried

out by a qualified electrician!

2. In order to connect the device to the mains, a power-plug must be installed.

3. Configuration of connection-cables is as follows:

Cable Pin International

Black Live L

White Neutral N

Green Ground

IEC

Cable Pin International

Brown Live L

Blue Neutral N

Yellow/Green Ground

4. The ground must be connected!

5. Connect the device to the mains with the power-plug.

6. If the device will be directly connected with the local power supply network, a

disconnection switch with a minimum opening of 3 mm at every pole must be

included in the permanent electrical installation.

1. Disconnect the unit from power before installing the lamp.

WARNING! Let lamp cool before changing.

2. Remove the color frame from its holder (Figure 1).

Note: To avoid premature lamp failure, do not touch the lamp glass with your fingers.

If you touch the lamp during installation, clean it carefully with 90% or better isopropyl

alcohol and a clean lint-free cloth before operation

3. Remove wire leads from screw terminals on back of old lamp. Connect wire leads

to replacement lamp screw terminals. Reinstall lamp in fixture.

4. Replace the color frame into the holder.

Installing the Iamp

Always replace the lamp if it becomes damaged or deformed.

Caution! Operating lamps above their rated voltage reduces

lamp life and can cause premature lamp failure. For

installation, use one PAR36 lamp as specified in the lamp

table.

Mark DecoPAR DPR36 Quick start guide

Brand: Mark

Model: DecoPAR DPR36

Category: Motorcycle Accessories

Type: Quick start guide

Download PDF

report

Mark DecoPAR DPR36 Quick start guide

Mark DecoPAR DPR36 Quick start guide

Related papers

Other documents