Davis Instruments Mark 3 Sextant User manual

Brand: Davis Instruments

Model: Mark 3 Sextant

Type: User manual

This manual is also suitable for

MARK 3

Mark 3 Sextant User’s Guide

00011.220, Rev. E

October 2008

Total pages 20

Trim to 5.5 x 8.

Black ink only

Page 1 (front cover)

EDITED BY ROBERT B. KLEID

How to Find Your Position

with the Mark 3 Sextant

STANDARD

MARK 3

#011

Mark 3 Sextant User’s Guide

Product #011

00011.220, Rev. E October 2008

INDEX SHADES

HORIZON

MIRROR

INDEX ARM

INDEX MIRROR

ADJUSTMENT

SCREWS

HORIZON

SHADES

EYE

PIECE

OPTIONAL PROTECTIVE CASE

Contact your local dealer or Davis Instruments to

order.

R014A Sextant Case

R014B Foam Set for case

Page 1

HOW TO FIND YOUR POSITION WITH A SEXTANT

This booklet has been written as an introduction to your new Davis sextant. By

studying its pages, you will learn how to operate your sextant, how to find the alti-

tude of the sun, and how to use your readings to calculate location. The meridian

transit method of navigation described is both easily learned and simply

applied. When you finish reading, the mystery surrounding celestial navigation

and sextant use should disappear. Before becoming an accomplished navigator,

however, you will need to study those aspects of navigation which are beyond the

scope of this booklet.

HOW TO READ THE VERNIER

There are two scales on the sextant. The scale on the frame is called the “arc,”

while the scale on the index arm is the “vernier.” Each division of the arc equals

one degree. Each division of the vernier equals two minutes (2'). To read the num-

ber of degrees, find the lines on the arc which are closest to the zero mark on the

vernier. The zero mark is usually somewhere between two lines. The correct arc

reading is always that of the lower value, i.e., the line to the right of the zero mark.

To read fractions of a degree, find the division of the vernier which is in alignment

with a division of the arc.

To get a clear picture of how this works, set the zero on the vernier exactly

beneath any whole degree mark on the arc—let’s say 30°. Now move the index

arm very slightly to the left until the first vernier mark to the right of the zero lines

up exactly with a mark on the arc. Since the marks on the vernier are 2' apart,

you have actually moved the index arm 2' beyond 30°; your sextant reads 30° 02'.

Now, move the index arm slightly further to the left so that the next division of the

vernier comes into alignment with a division of the arc. Your sextant now reads

30° 04' (Fig. 1).

As you continue moving the index arm, successive divisions of the vernier will

come into alignment with a division of the arc. When the last mark on the vernier

(60') is in alignment with a division of the arc, the sextant will read 31°. In figure 2

below, the sextant reads 43° 26'.

Figure 2

Figure 1

Page 2

MARK 3 SEXTANT ADJUSTMENT

Adjusting your Mark 3 Sextant is easy and should be done each time it is used.

All adjustments are made with the index mirror, the large movable mirror at the

pivot of the index arm (it is not necessary to adjust the small horizon mirror, as

the unit construction makes it impossible to be very much in error). On a correctly

adjusted sextant, the index mirror is perpendicular to the frame and becomes par-

allel to the horizon mirror when the sextant reads zero.

First, adjust the index mirror for “side error” by making it perpendicular to the

frame. Holding the sextant in your right hand, raise the instrument to your eye.

Look at any horizontal straight edge (the sea horizon, for example, or the roof of a

building al least one mile away) and move the index arm back and forth. The real

horizon will remain still while the mirror horizon will appear only when the scales

read close to zero. Line up the mirror horizon and the real horizon so that both

appear as a single straight line (fig. 3).

Now do a vertical adjustment. Without changing the setting, look through the

sextant at any vertical line (a flag pole, for example, or the edge of a building) and

swing the instrument back and forth across the vertical line. If the index mirror is

not perpendicular to the frame, the line will seem to jump to one side as the mirror

passes it. To correct this, slowly tighten or loosen the screw closest to the frame at

the back of the index mirror until the vertical line no longer appears to jump (fig. 4).

Figure 4

Mirror horizon is not aligned with

the real horizon—index arm is not

in proper position.

Index mirror screw

too tight.

Index mirror screw

correctly adjusted.

Index mirror screw

too loose.

Mirror horizon and real horizon

form a single straight line—index

arm is properly positioned.

Figure 3

Page 3

Finally, remove the index error. Set the sextant at zero and look at the horizon.

With the sextant still held to your eye, turn the screw that is furthest from the

frame at the back of the index mirror until the two horizons move together and

form one straight line. The index mirror is now parallel to the horizon mirror (Fig. 5).

While you should know how to adjust your sextant for index error, it is not neces-

sary to remove it entirely. It is standard practice to simply note the error and then

correct one’s reading for this amount each time the sextant is used (as much as 6'

index error is allowable). To check for index error, hold the sextant in your right

hand and look at the sea horizon. By moving the index arm, line up the real and

mirror horizons so that both appear as a single straight line. Now, look at the

scale. If it reads zero, there is no index error. If the scale reads anything but zero,

there is an index error which must be added to or subtracted from each reading.

For example, if the scale reads

+6' when the horizons are aligned, the 6’ is sub-

tracted. If the reading is below the zero mark, for example –6', the 6' is added

(Note: for an index error of –6', the scale actually reads 54').

MEASURING THE SUN’S ALTITUDE

When looking at the sun through the sextant, be sure to use a sufficient num-

ber of shades to protect your eyes from the direct rays of the sun. Choose

the combination of index and horizon shades that gives you a clear image of the

sun without glare.

On a correctly adjusted sextant, the real and mirror horizons remain in a single

line when the instrument is rocked from side to side (Fig. 6).

Index mirror not parallel to

horizon mirror.

Index mirror parallel to

horizon mirror.

Figure 5

Figure 6

Page 4

To measure the sun’s altitude, stand facing the sun with the sextant in your right

hand. With your left hand on the index arm, look through the eye piece at the hori-

zon and move the index arm until the sun is visible through the two mirrors and

index shades. Rock the entire sextant from side to side so that the sun’s image

travels in a half-arc. Now, adjust the index arm to bring the sun’s image down to

just touch the horizon (Fig. 7).

Being careful not to disturb the setting, read the sun’s altitude from the scales on

the sextant. Since all calculations in the Navigation Tables use the center of the

sun or moon, this lower limb reading must be adjusted for semi-diameter correc-

tion, shown later.

HEIGHT OF EYE

When measuring the altitude of the sun, we want to measure the angle formed by

a ray from the sun and a plane tangent to the earth at the point where the observ-

er is standing. Due to the height of the eye of the observer, however, the visible

horizon actually falls below this theoretical plane (Fig. 8).

Figure 7

Figure 8

The sun’s image travels

in a short arc which just

touches the horizon.

Due to the height of the eye of the observer, the

visible horizon (H) falls below the plane (P) tan-

gent to the earth at the point where the observer

is standing.

To correct for the height of

the eye, one must apply a

“dip correction.” Dip correc-

tion increases as the eye is

raised further above the sur-

face of the water (Table 1)

and must always be subtract-

ed from the sextant reading.

Table 1

Height of Eye Correction

Feet Meters Dip

5 1.5 2'

10 3.0 3'

15 4.5 4'

25 7.5 5'

40 12.0 6'

Page 5

A nautical mile is equal to one minute of arc of a great circle. Since latitude is

measured north or south from the equator, it is measured along a meridian

(a great circle). One minute of latitude equals one nautical mile anywhere on the

earth. Since longitude is measured east or west from the prime meridian (zero

degrees) at Greenwich, England, it is measured along a parallel of latitude

(a small circle). One minute of longitude equals one nautical mile only at the

equator. Approaching the poles, one minute of longitude equals less and less of

a nautical mile (Fig. 10).

LATITUDE, LONGITUDE, and the NAUTICAL MILE

A great circle is a circle on the surface of the earth, the plane of which passes

through the center of the earth. A small circle is a circle whose plane does NOT

pass through the center of the earth. The equator and the meridians are great cir-

cles, while parallels of latitude are small circles which become progressively

smaller as the distance form the equator increases. At the poles (90° N or S), they

are but single points (Fig. 9).

The plane of a meridian (a great

circle) divides the earth into two

equal halves.

The plane of a parallel of latitude

(a small circle) divides the earth

into two unequal parts.

Figure 9

Figure 10

Note that the nautical mile is about

15% longer than the statute mile:

Nautical Mile Statute Mile

6076 feet 5280 feet

1852 meters 1609 meters

The earth measures 21,600 nautical

miles in circumference (24,856 statute

miles).

Page 6

DECLINATION

Every star and planet, including the sun, has a ground position, i.e., the spot on

the earth directly beneath it. Standing at the sun’s ground position (G.P.), you

would have to look straight up to see the sun; if you were to measure its altitude

with a sextant, you would find the altitude was 90°.

From the earth, the sun seems to move across the sky in an arc from east to

west. During certain times of the year, it is “moving” around the earth directly

above the equator or, in other words, the sun’s G.P. is running along the equator.

Declination of the sun at this time is zero. However, the sun’s G.P. does not stay at

the equator throughout the year. It moves north to a maximum of 23

/2° N in the

summer of the northern hemisphere, and south to a maximum of 23

/2° S in the

winter. The distance of the sun’s G.P. from the equator, expressed in degrees

north or south, is known as the declination of the sun (Fig. 11).

In like manner, each star has a ground position and a declination. The decli-

nation of Polaris is 89° 05' N; it is nearly directly above the North Pole. In the

northern hemisphere, you can find your approximate position by taking a sight on

Polaris. The reading will vary depending upon the time of night but will never be

more than 55 miles off. This is a useful check each evening; the altitude of Polaris

will be your approximate latitude without adding or subtracting anything. If you

were to find the altitude of Polaris in the evening and again at dawn, your true lati-

tude would be between the two measurements,

providing you did not change latitude between the

two sights. It is, of course, possible to calculate

one’s exact latitude from Polaris with the aid of the

Nautical Almanac, but such a discussion is beyond

the scope of this booklet.

To find POlaris, locate the pointers of the Big

Dipper (Fig. 12). Find a point in line with the point-

ers and five times the distance between them.

There, shining alone, is Polaris. The Big Dipper

revolves around Polaris, so be prepared to see the

diagram in any position.

Figure 12

Figure 11

Page 7

FINDING LOCAL NOON & THE SUN’S ALTITUDE

AT MERIDIAN PASSAGE

A meridian is an imaginary line drawn on the earth’s surface from pole to pole; a

local meridian is one which passes through the position of an observer. When the

sun crosses the local meridian, it is at its highest point. It is said to be in meridian

passage and the time is local noon. Local noon may vary a half an hour (and in

daylight savings time, one and one-half hours) from the noon shown on the clock,

due to both the equation of time (to be discussed later) and the fact that our

clocks are set to zone time. All clocks in a zone 15° wide show the same time.

To find local noon, follow the sun up with a series of sights, starting about half an

hour before estimated local noon. Note the time and the sextant reading carefully.

Take a sight about every three minutes until the sun’s altitude is no longer

increasing. During meridian passage, the sun will seem to “hang” in the sky for a

short period at its highest point, going neither up nor down. Carefully note the

sextant reading. This is the sun’s altitude at meridian passage. To determine

the exact time of local noon, set your sextant at the same altitude as your first

sight. Wait for the sun to drop to this altitude, and note the time again. The time of

local noon is exactly half way between the times of the two sights.

Record the local time and the sextant reading when the sun was at the highest

point. These two readings will serve to locate your position. The time is used to

determine longitude and the sextant reading to determine latitude.

AN EXAMPLE OF A COMPLETE SIGHT

Let us assume for this example that your ship is sailing from San Francisco to

Hawaii and you have been using the sun to find your position each day. To allow

plenty of time to follow the sun up to its highest point, you make sure that you

have completed all your preparations by 10:00 a.m. local time. Your chart shows

yesterday’s position. From this position, you draw a line in the direction you are

traveling equal in length to the estimated number of miles to be traveled by noon

today. This is your “dead reckoning position” (D.R.), which will be compared with

your “noon sight.”

You note that you are standing on deck with your eye ten feet above the water (for

Dip correction) and that the index error of your sextant is

+5'.

At about 11:20 a.m., you begin taking sights. At 11:23:30, your first sextant read-

ing is 82° 56'. You continue recording the sun’s altitude approximately every three

minutes until the sun seems to “hang” in the sky, dropping to a lower altitude at

your next sight. The maximum altitude of the sun, 84° 56', is the altitude of the

sun at meridian passage. You continue taking sights until 12:03:30, when the sun

has dropped to your original reading of 82° 56'. You know that the sun reached its

Page 8

FINDING LONGITUDE

Meridians of longitude are measured east or west from the prime meridian (zero

degrees) at Greenwich, England. Because the ground position of the sun moves

around the earth at an average speed of 15° per hour (15 nautical miles per

minute), longitude may be calculated by comparing local noon with

Greenwich Mean Time. For example, if local noon occurred at 2:00 GMT, your

longitude is approximately 30° west of Greenwich (2 hours x 15°/hour = 30°).

To determine one’s exact position, the equation of time must be applied. The

earth in its orbit around the sun does not travel at a constant speed. Clocks and

watches, therefore, keep the time of a fictitious or mean sun which travels at the

same average speed throughout the year, and the position of the true sun (as

seen from the northern half of the earth) is not always due south or 180° true at

noon by the clock. The difference in time between the true sun and the mean sun

is call the “equation of time.” The equation of time for any given day may be found

in a Nautical Almanac; its approximate value may be found in the student tables at

the end of this booklet.

See figure 13 for a diagram based on this example.

meridian at 11:43:30 (exactly half the time between 11:23:30 and 12:03:30). Next,

you find the Greenwich Mean Time (GMT) of your local noon by listening to the

radio time signal, correcting any error your watch may have had. In this example,

you tune in the time signal and find that GMT is now 22:10:00. Your watch reads

12:10:00, so it has no error. You know that your local noon occurred at GMT

21:43:30 (26 minutes 30 seconds ago).

You now have enough facts to work out your noon sight: the date, the time of

meridian passage (local noon), the altitude of the sun at meridian passage, the

height of your eye above the surface of the sea, and the index error of the sextant

you are using.

Page 9

FINDING LATITUDE

The altitude of the sun at local noon may also be used to calculate latitude. First,

the measured altitude must be corrected for index error, height of eye, refraction,

and semi-diameter. Refraction correction is negligible for altitudes above 25°,

while the semi-diameter correction averages

+0° 16' (semi-diameter correction

adjusts the sextant reading from an observation of the lower limb of the sun to

one of the center of the sun; 16' equals one-half the sun’s diameter). After the cor-

rections are made, determine the declination of the sun from the Nautical

Almanac or from the approximate declination values at the end of this booklet.

Finally, calculate latitude by combining the altitude of the sun at local noon with

the declination of the sun from the navigation tables. Assuming you are north of

the sun, the following formula is used in northern latitudes:

Latitude = 90° – Corrected Altitude

± Declination of the Sun

When the sun is north of the equator, ADD the declination; when it is south of the

equator, SUBTRACT the declination.

See figure 14 for a diagram based on this example.

Page 10

Presentations shown here are commonly used by navigators to help insure the

accuracy of their calculations:

Figure 13 Figure 14

Longitude Diagram

(view of earth looking at

the South Pole)

Latitude Diagram

(view of earth looking at

the Equator)

Figure 14

Position plot

on a chart.

SYSTEMS OF CELESTIAL NAVIGATION

The method described above for calculating your position is the oldest method

used since the introductions of the chronometer. Please note the following:

1. Latitude may be determined at noon if you know the corrected altitude of the

sun and its declination. You need not know the time. The accuracy of your cal-

culation is limited only by the accuracy of measurement of the sun’s altitude

and by the accuracy of the declination tables.

2. To determine longitude, you must know both the time of observation and the

equation of time. While your sextant gives highly accurate measurements, prac-

tical difficulties inherent in this method normally preclude accuracy of more

than 10' of longitude.

THE ARTIFICIAL HORIZON

At times, it is not possible to see the natural horizon. Sun or moon shots may still

be taken, with the aid of an artificial horizon—a simple device containing water or

oil shielded from the wind (see below). It may be used by individuals exploring

inland far from the sea, or by students or experienced navigators to practice

celestial navigation without traveling to large bodies of water.

Page 11

Davis Instruments manufactures the Davis

#144 Artificial Horizon, pictured here. The

instrument is wind-proof and corrosion resis-

tant; its reflecting surface is completely

enclosed. Two sun shades and a lid are

included.

A generalized system of position determination which enables you to use obser-

vation of the sun and other celestial bodies made at times other than noon

requires knowledge of the navigation triangle, circles of equal altitude, assumed

position, and associated navigation tables such as the Nautical Almanac and

Sight Reduction Tables. These systems of celestial navigation are thoroughly stud-

ies and extensively used by serious navigators throughout the world.

Sets of work forms for the Sight Reduction Tables are used by nearly all naviga-

tors to help prevent errors and omissions in the calculation of celestial navigation

problems.

To use an artificial horizon:

1. Position the artificial horizon on level ground or other steady place. One end of

the artificial horizon should face directly into the sun so that a shadow is cast at

the opposite end. The sides and end facing the sun should be shadow-free.

2. Looking into the center of the liquid, move your head about so that you can see

the sun reflected on the liquid surface.

3. Bring the sextant to your eye and move the index arm of the sextant until you

see two suns—on reflected on the liquid and a double-reflected image on the

mirrors.

Page 12

THE SEXTANT AS A PELORUS

Your sextant may also be used to find your position by sighting known land

objects such as lighthouses, small harbors, or any other land features that are

clearly recognizable on the chart. Pick out three features on the land. With the

sextant held horizontally, measure the angle between the center feature and one

of the other features, and note the angle on a piece of paper. As quickly as you

can, measure the angle between the center feature and the third feature. Lay out

the three angles on a piece of tracing paper so that the angles have a common

center point. Move the tracing paper around on the chart until the lines are posi-

tioned so as to run through the three features. The point of intersection of the

three angles is your position (Fig. 17).

Note: Since the sextant reading made with an artificial horizon must be halved,

the maximum altitude that you can observe with the artificial horizon is equal to

one-half the maximum arc graduation on your sextant. There may be several

hours around noon during which the sun is too high to take a sextant reading with

the artificial horizon, so plan sights for the morning or evening hours.

Figure 16

4. Line the two suns up by continuing to move the index arm. For a lower limb

observation, bring the bottom of the mirror image into coincidence with the top

of the image on the liquid.

5. After the observation has been made, apply the index correction.

6. Halve the remaining angle and apply all other corrections (except for Dip or

height of eye correction, which is not applicable) to find the altitude of the sun.

Page 13

THE SEXTANT AS A HELIOGRAPH

You can use the sextant mirror to flash the sun’s rays several miles to attract

attention, or to signal another person who is too far away for your voice to reach.

If you know Morse code, you could even send a message.

1. Hold the sextant so that the index mirror (the larger of the two mirrors) is just

below the eye.

2. With your other arm extended and the thumb held upright, look at the person

you wish to signal.

3. Hold your thumb to a position just below the person, so that your eye (with the

mirror under it), your thumb, and the person are in a straight line (Fig. 18).

4. Using the mirror, flash the sun on your thumb. The sun flashes simultaneously

on the distant person.

Figure 17

Figure 18

Since the sextant does not have a compass, you don’t need to worry about varia-

tion or deviation. However, you must use at least three lines of position.

Page 14

STUDENT NAVIGATION TABLES

The tables on the following pages give the approximate declination and equation

of time of the sun. Latitude calculated with these values will be accurate to about

±15'. The tables are thus intended for study purposes only, although they may be

used for emergency navigation.

NAUTICAL ALMANACS, CHARTS and

TABLES

The Nautical Almanac is published yearly by

the U.S. Naval Observatory and the H.M.

Nautical Almanac Office, Royal Greenwich

Observatory, U.K. It may be purchased from the

superintendent of Documents, U.S.

Government Printing Office, Washington, D.C.,

or from many marine and chart dealers.

Sight reduction tables, plotting sheets and star

finders are also available from many marine

and chart dealers.

FURTHER RESOURCES

Books for learning celestial navigation are available in many maine stores and

larger bookstores. Most often recommended are The American Practical

Navigator (U.S. Navy Hydrographic Office) and Dutton’s Navigation and Plotting

(U.S. Naval Institute). Other popular and regularly available titles are published by

Cornell Maritime Press and the International Marine Publishing Co.

Videos are available from larger marine dealers, video mail order houses, and

online.

Schools and courses are offered from local planetariums and community col-

leges in coastal areas. The U.S. Power Squadron (Raleigh, NC) also conducts

regional classes. Other schools and correspondence schools include the

International School of Sailing (Fort Lauderdale, FL) and Ocean Navigator

Training Courses (Portland, ME).

Home study classes may be ordered from the International Navigation School

(Toronto, Ontario, Canada), Starpath School of Navigation (Seattle, WA), Florida

Maritime Institute (Stuart, FL), The Annapolis Sailing School (Annapolis, MD), and

Coastal Navigation (Annapolis, MD).

Page 15

REFERENCE:

Approximate Declination & Equation of Time

Page 16

Page 17

Includes everything you need: sextant

use and corrections, starfinder for 18

stars, data entry form and step-by-step

sight reduction and plotting proce-

dures.

#132

3465 Diablo Ave., Hayward, CA 94545 U.S.A.

Phone (510) 732-9229 • Fax (510) 732-9188

inf[email protected] www.davisnet.com

REPLACEMENT PARTS

Contact your local dealer or Davis

Instruments to order. Specify that your

sextant is the #011 Mark 3.

R011A Index Shade Assembly

R011B 4 Springs, 2 Screws, 3 Nuts

R011C Index & Horizon Mirrors

w. Springs, Screws, Nuts

R011X Factory overhaul

($10.00 estimated charge)

CELESTIAL NAVIGATION

AT A GLANCE

Celestial Navigation

Quick Reference Card

This full-color, weatherproof plastic

card presents a simplified yet complete

celestial navigation system. Makes it

easy, proving that lengthy instruction is

not necessary to master the subject.

OTHER DAVIS SEXTANTS

In addition to the Mark 3, Davis offers

two models of master marine sextants.

The Mark 15 offers professional

features—including micrometer drum,

traditional styling, and greater accuracy

than the Mark 3. Allows readings up to

2/10 minute of arc. 3 x 27 mm star

telescope. Precision machined, slow

travel gear and worm mechanism.

#026

The Mark 25 has all the features of the

Mark 15 plus LED lighting and the

patented Beam Converger horizon mir-

ror, which replaces the conventional

half-silvered mirror. The Beam

Converger combines the horizon and

astrobody images into a single full-field

view for easy, reliable sights under the

most difficult conditions. Constructed

with stronger and more stable materi-

als to make this the most accurate of

the Davis sextants.

#025

File page 20 (back cover)

Davis Instruments Mark 3 Sextant User manual

Brand: Davis Instruments

Model: Mark 3 Sextant

Type: User manual

This manual is also suitable for

MARK 3

Download PDF

report

Davis Instruments Mark 3 Sextant User manual

This manual is also suitable for

Davis Instruments Mark 3 Sextant User manual

Related papers

Other documents