Sea gull lighting 77088-98 Installation guide

Brand: Sea gull lighting

Model: 77088-98

Type: Installation guide

*OUTLET

BOX

FIXTURE

MOUNTING

SCREWS (C)

*WIRE

CONNECTORS

MOUNTING

BAR (A)

*OUTLET

BOX SCREWS

KEYSLOTS (N)

INSTALLATION AND SAFETY INSTRUCTIONS

FOR YOUR SAFETY

GENERAL

ASSEMBLY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE

WORKING ON IS SHUT OFF; EITHER THE FUSE REMOVED OR THE

CIRCUIT BREAKER SET AT OFF.

You don't need special tools to install this fixture. Be sure to follow the

steps in the order given. Under no circumstances should a fixture be hung

on house electrical wires, nor should a swag type fixture be installed on a

ceiling which contains a radiant type heating system. Read instructions

carefully. If you are unclear as to how to proceed, consult a qualified

electrician.

BRACKET (I)

CANOPY (E)

GLASS (H)

RING (G)

TABS (L)

BALL NUTS (J)

FIGURE 1

*NOT INCLUDED

Carefully remove the fixture from the carton and check that all

parts are included, as shown in figure 1 and 2. Be careful not

to misplace any of the screws or parts which are needed to

install this fixture.

STEP 1:

Before mounting canopy (E ) to mounting bar (A), place canopy

(E) on flat surface. Next place ring (G) over canopy (E) making

sure the three brackets (I) protrude through holes in canopy (E).

If they do not, adjust the brackets (I) so that they align with the

canopy (E) holes.

NOTE: IF LIGHT LEAKAGE IS PRESENT, SLIGHTLY BEND

THE BRACKETS (I) TOWARDS THE CEILING.

NOTE: FOR FIXTURES PROVIDED WITH 75˚ C OR 90˚ C

SUPPLY WIRE WARNING ONLY- (THESE WARNINGS ARE

PROVIDED ON THE U.L. LABEL AND ON THE FIXTURE

CARTON): RISK OF FIRE. MOST DWELLINGS BUILT

BEFORE 1985 HAVE SUPPLY WIRE RATED 60˚ C. CONSULT

A QUALIFIED ELECTRICIAN BEFORE INSTALLING.

IF SUPPLY WIRES ARE LOCATED WITHIN 3” OF BALLAST,

USE WIRE RATED FOR AT LEAST 90˚C.

Installation And

Safety Instruction

HC-471

052699

Fill In Item Number On Carton And

File This Sheet For Fixture Reference. ITEM#_____________

GREEN

GROUNDING SCREW (D)

*OUTLET BOX

SCREWS

MOUNTING

BAR (A)

*WIRE

CONNECTORS

MOUNTING

SCREWS (C)

*GROUND WIRE

*OUTLET BOX

GROUNDING AND MOUNTING BAR LOCK UP

FIGURE 2

*NOT INCLUDED

INSTALLATION HC-471

FINAL ASSEMBLY

STEP 6:

IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET

BOX.

STEP 2:

STEP 1:

Make sure no bare wires can be seen outside wire connectors.

Install lamp (s).

Place glass (H) inside ring (G) and secure in place with tabs (L)

attached to ring (G).

STEP 3:

Raise ring (G) to canopy (E) so that threaded brackets (I) protrude

through holes in ring (G) and secure in place with ball nuts (J).

STEP 4:

STEP 3:

A. Take note of the color of the wire(s) on your fixture. Identify

which group your fixture wire(s) falls into and connect the wires

according to the directions below:

*Note: When parallel wire is used, the tracer wire is square shaped

or ridged and less tracer wire is round in shape or smooth.

(Seen best when viewed from wire end.) To separate wires, grasp

the ends of each wire and pull apart.

B. Take your fixture wire(s) from group A and place evenly against

the black wire from the outlet box. DO NOT twist wires together

before using wire connectors.

C. Fit a wire connector (not supplied) over the wires and screw the

connector clockwise until you feel a firmness.

D. Try gently to pull the connector off the wires. If you can pull the

connector off, carefully re-do steps B and C, as above and check

again for a firm connection.

E. Connect the fixture wire from group B to the white wire from the

outlet box in the same manner.

GROUNDING INSTRUCTIONS: The green grounding screw (D) is

to be inserted into the hole with two raised dimples provided on the

mounting bar (A). Wrap the ground wire (M) from the fixture (if supplied)

and the ground wire from the outlet box (bare metal or green

insulated wire) around the green grounding screw (D) on the

mounting bar (A) if uninsulated wire is on the mounting bar (A),

connect the ground wire (M) from the fixture (if supplied) and the

outlet box to it using a small wire connector (not supplied).

NOTE: Underwriters Laboratories (U.L.) does not require all fixtures to

have ground wires. These fixtures still meet all U.L. specifications. The

listing mark of Underwriters on the product identifies products

manufactured under its listing and Follow-Up Service Programs.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE

POWER SUPPLY WIRES.

GROUP A: CONNECT TO BLACK

HOUSE WIRE

BLACK

WHITE

*PARALLEL WIRE (ROUND & SMOOTH)

WHITE OR GREY WITH TRACER

BROWN, GOLD OR BLACK WITHOUT

TRACER

BROWN, GOLD OR BLACK WITH TRACER

WHITE OR GREY WITHOUT TRACER

*PARALLEL WIRE (SQUARE & RIDGED)

GROUP B: CONNECT TO WHITE

HOUSE WIRE

CLEANING

To clean, wipe fixture body with a soft cloth. Clean glass with a mild

soap. Do not use abrasive materials such as scouring pads or

powders, steel wool, or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order

replacement parts. All parts for this fixture can be ordered from place

of purchase. Be sure to use exact wording from illustration when

ordering parts.

After wires are connected, tuck them carefully inside outlet box.

Raise the canopy (E) to the ceiling allowing for mounting screws (C)

to protrude through key slots (N). Rotate canopy (E) clockwise until

screws (C) are in narrow part of keyslot (N). Tighten screws (C) with

screwdriver.

STEP 1:

STEP 2:

Secure mounting bar (A) to outlet box with outlet box screws (not

supplied). Raised side is top as illustrated.

Thread fixture mounting screws (C) into threaded holes of

mounting bar (A) 3 turns each.

Sea gull lighting 77088-98 Installation guide

Sea gull lighting 77088-98 Installation guide

Sea gull lighting 77088-98 Installation guide

Related papers

Other documents