none W-JOY-20 Installation guide

Type
Installation guide

none W-JOY-20

The none W-JOY-20 is an electrical seasonal use product intended for decorating trees and other similar structures. It comes with a tree stand, a bottom section, a middle section, a top section, and a light string. The light string cords from the bottom section should be plugged into the middle section, and the cord from the top section should be plugged into the middle section. The hinged branches should be gently lowered by hand during assembly and shaped to give the tree a natural look. The tips of each branch should be spread out away from the center tip and then bent slightly upward.

none W-JOY-20

The none W-JOY-20 is an electrical seasonal use product intended for decorating trees and other similar structures. It comes with a tree stand, a bottom section, a middle section, a top section, and a light string. The light string cords from the bottom section should be plugged into the middle section, and the cord from the top section should be plugged into the middle section. The hinged branches should be gently lowered by hand during assembly and shaped to give the tree a natural look. The tips of each branch should be spread out away from the center tip and then bent slightly upward.

ASSEMBLY
INSTRUCTIONS
READANDFOLLOWALLSAFETY
INSTRUCTIONS
Do not use seasonal products outdoors unless
marked suitable for indoor and outdoor use.
Whenproductsareusedinoutdoorapplications,
connect the product to a Ground Fault Circuit
Interrupter (GFCI)outlet. If one is not provided,
contact a qualified electrician for proper
installation.
This seasonal use product is not intended for
permanentinstallationoruse.
When decorating trees, use miniature light
bulb strings or LED light strings only. “C” size
bulbsarenotrecommended.
Do not mount or place near gas or electric
heaters, fireplaces, candles or other similar
sourcesofheat.
Do not secure the wiring of the product with
staplesornails,orplaceonsharphooksornails.
Unplug the product when leaving the house,
whenretiringforthenight,orifleftunattended.
CAUTION:Thisisanelectricalproduct–notatoy!
To avoid risk of fire, burns, personal injury and
electric shock, it should not be played with or
placedwheresmallchildrencanreachit.
Donotletlampsrestonthesupplycordor any
wire.
Do not use this product for other than its
intendeduse.
Do not hang ornaments or other objects from
cord,wireorlightstring.
Do not close doors or windows on the product
orextensioncordsasthismaydamagethewire
insulation.
Neveroperate thisproductifthepowercordor
plugisdamaged.
Use only manufacturer specified replacement
bulbs.
Read and follow all instructions that are on the
productorprovidedwiththeproduct.
USEANDCAREINSTRUCTIONS
Whenstoringthe product,carefully remove the
product from wherever it is placed, including
trees, branches, or bushes, to avoid any undue
strain or stress on the product conductors,
connections,andwires.
When not in use, store neatly in a cool, dry
locationprotectedfromsunlight.
CAUTION:
IMPORTANT SAFETY INSTRUCTIONS
Retaincartonforstoragepurposes.
Eachcartoncontainsonetopsection,onebottomsection
andatreestand.
1. Unfold the tree stand and insert the eye bolts. Insert
bottom section pole into tree stand making sure it is
seatedproperly(Figure1).Tighten eyeboltsuntilbottom
sectionisheldsecurely.
2. Insert the middle section of the tree into the
bottomsection.
3. Plug the light string cords from the bottom
section to the middle section. Attention! There
are two different strings for, cord with Red tag
shouldbepluggedtogether,andcordwithouttag
shouldbepluggedtogether.
4. Insert the top section of tree into the upper
mostpart ofmiddle section. Plug the light string
cordofthetop sectionintothereceptacle of the
middlesectionlightstringswithseparatetwo.
5. Final step is branch shaping.All hingedbranches
shouldfallintolowered positionduringassembly.
Any branches that remain upright should be
gently lowered by hand (see Figure 3 and 4).
Please refer toShaping Instructionsfor proper
branchshapingtechnique.
STORAGE
Removeallholidaydecorations.Gentlypresstipsbackinto
centerbranch.Raiseallbranchestooriginalupright
positiontakingcarenottoplaceunduepressureonthe
attachedendsofthebranches.Whendisassemblingtree,a
twistingmotionwillhelptoseparatethesectionsfrom
eachother.Alltreepartscanbereplacedincartonand
shouldbestoredinacool,dryplace.
BULBREPL ACEMENTINSTRUCTIONS
1. Unpluglightstringfrompowersource.
2. Pull up on the Bulb Lock (if equipped) unlatching
thebulbfromthebulbsocket.Gentlypullthebulb
straightout(Figure1).
3. Before inserting the new bulb into socket, make
sure that the two wires on either side of the the
bulb base are straight up and flush with the base
(diagramatright).
4. Carefullyinsertnewbulbintosocketandpushdown
BulbLock(ifequipped)untilitsnapsintoplace(Figure2).
FUSEREPLACEMENT
INSTRUCTIONSUSONLY
1. Unpluglightstringfrompowersource.
2. Fusesarelocatedinlightstringplug.Slidethefuse
access cover away from cord side (in direction of
arrow,Figure1)exposingfuses.
3. Remove fuses from compartment and examine.
Replaceburn toutfusewithnewone.
4. Closefusecompartmentbyslidingaccesscover
backintowardscordsideofplug(Figure2).
SHAPINGINSTRUCTIONS
Shapingthetreebranchesisthelaststepofassembly.
The care and attention given to this final process will
result in a genuinely beautiful and appealing holiday
centerpiece.
1. Every tree style is shipped from the factory with
the tips of each branch compressed to the center
(Figure1).
2. Each branch tip must be shaped to its proper
position to give the tree a natural look. This is
donebygentlygraspingtheleftandrightwingtips
and spreadingthem out away fromthe centertip
(Figure2).
3. Each individual tip should then be spread out
separately. Tips should then be bent slightly
upwardtoaddamorenaturallookingappearance.
Figure3showsatypicaltreebranchaftershaping.
Branchtipsshouldbecarefullypressedbacktowardcenter
tipwhentreeisdisassembledforstorageinoriginalcarton.
SAVETHESEINSTRUCTIONS
  • Page 1 1
  • Page 2 2
  • Page 3 3

none W-JOY-20 Installation guide

Type
Installation guide

none W-JOY-20

The none W-JOY-20 is an electrical seasonal use product intended for decorating trees and other similar structures. It comes with a tree stand, a bottom section, a middle section, a top section, and a light string. The light string cords from the bottom section should be plugged into the middle section, and the cord from the top section should be plugged into the middle section. The hinged branches should be gently lowered by hand during assembly and shaped to give the tree a natural look. The tips of each branch should be spread out away from the center tip and then bent slightly upward.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI