KIA 1U056 ADU00 Installation Instructions Manual

KIA
Brand
KIA
Model
1U056 ADU00
Type
Installation Instructions Manual
Revision Date
4/22/2013
Page 1 of 25
Vehicle Model Sorento (Key Start) Accessory Remote Engine Start
Model Year 2014 ~ Diffi culty ( B )
Part No. 1U056 ADU00
KIA Genuine Accessories
Instruction Symbols / Defi nitions
Note: Diffi culty stated above refl ects the minimum level of expertise required to install the accessory
( A ) Customer ( B ) Dealer Technician ( C ) Master Technician
Denotes warnings that may lead to
serious physical injury or vehicle
damage.
Denotes cautions to be taken to avoid
physical injury or electronic component
damage.
Denotes cautions to be taken to avoid
vehicle and component damage.
Denotes quality processes to be
checked prior to moving to the
next step.
Denotes specifi c tools that are neces-
sary to complete the step.
Denotes instructional steps
necessary to complete the
process.
Denotes safety equipment required to be used
such as a mask, goggles, rubber
gloves, and hearing protection.
N
O
T
E
Notes to the Installer:
Read the entire installation manual prior to beginning the installation of the
accessory.
Factory wire harness colors are subject to change, please use the specifi ed pin
# in the harness connector to identify the correct wire for T-Tap installation.
Ensure that the vehicle is properly protected in the area that the accessory is to
be installed.
To prevent vehicle damage, never place tools on top of painted surfaces, seats,
dash pad, console or fl oor carpet / mat.
Always wear appropriate safety gear to include gloves and eye protection when
required.
To prevent stress on the remote start wire harness, ensure the tilt/telescopic
steering column is fully extended, if equipped.
Ensure the transportation fuse is properly installed before performing the
function check on page 17.
Technical Support
For Authorized Dealers - (800) 667-5176
Hours: 9:00 a.m. - 5:30 p.m. EST Monday - Friday
Basic Required Hand Tools
Mask
Rubber Gloves Hearing Protection
Goggles
Ensure vehicle is equipped with automatic transmission, power door locks
and power windows. If the vehicle is not equipped with these options, do
not proceed. Ensure vehicle does NOT have SMART KEY.
!
P/N: 4280516, Rev. A
Ratchet
#2 Phillips
Screwdriver
Trim Tool
Wire Cutter
Pliers
10 mm Socket
Alcohol Cleaner /
Clean Cloth
Extension
Torque Wrench
Tape Measure
Revision Date
4/22/2013
Page 2 of 25
No. Qty. Description No. Qty. Description
1 1 Control Module/DNA 6 1 Installation Instructions
2 1 Dipole Antenna 7 1 Owner’s Guide
3 2 Transmitters 8 1 Quick Reference Guide
4 1 Wire Harness 9 1 Warning Label
5 1 Hardware Kit 10 6* 15” Wire Tie (Large)
Control Module P/N: U8560 00002
DNA P/N: 1U056 ADUS1
P/N: 00056 ADU50 P/N: U8560 00009
P/N: 1U056 ADUS2
7
8
1 2 3 4 5
9
Owner’s Guide Quick Reference Guide
Warning Label
15” Wire Tie (Large)
8” Wire Tie (Small)
12*
A
Female T-Tap
2*
B
1
D
Hardware Kit Total
18
M6 Serrated Flange
Hex Nut
6
10
3
C
Small Foam Tape
Hardware Kit
Installation Instructions
Hardware Kit Contents
KIA Genuine Accessories
* Extra components intentionally placed in kit as spares. Please follow directions for proper placement of each component.
Revision Date
4/22/2013
Page 3 of 25
T-Tap Installation Procedure
Factory wire harness colors are subject
to change. Please use the specifi ed pin
# in the harness connector to identify
the correct wire for T-Tap installation.
INCORRECT INCORRECT
Spade Terminal
Pointed Down
Spade Terminal
Pointed Up
1. Place T-Tap on vehicle wire.
2. Using pliers, close and crimp
T-Tap around vehicle wire.
3. Insert harness wire with
male spade terminal
end into the T-Tap.
CORRECT
Spade Terminal CENTERED
Inside Connector
Disconnecting Connectors
When disconnecting connectors, grasp the connec-
tors, not the wires.
Wire Colors
When a two-color wire is listed, the fi rst color indicates
the base color of the wire, the second color indicates
the color of the stripe. For example: Black/White.
Locking Connectors
When locking connectors, listen for a click indicating
they are securely locked.
Connector Diagrams
Connector diagrams may be shown on the har-
ness side or the terminal side, extreme care must
be taken to verify proper terminal location before a
T-Tap connection is made.
N
O OO
D
NO GOOD
White
(Stripe Color)
Black
(Base Color)
Striped Wire
Solid Wire
Black
** Extreme care must be taken to ensure that the male spade
terminal is inserted into the T-Tap properly.
Terminal End View
Harness End View
KIA Genuine Accessories
Revision Date
4/22/2013
Page 4 of 25
Vehicle Preparation
0
1. Remove the fuse panel access cover to assist in
the removal of the driver’s side dash end cap.
2. Remove the driver’s side dash end cap panel by
prying outward to disengage the four (4) pressure
clips.
Trim Tool
2
N
O
T
E
1. Clean hands.
2. Set the parking brake and open driver’s door window.
3. Vehicle should be at room temperature.
4. Ensure vehicle is equipped with automatic transmission, power door locks and power windows. If the vehicle
is not equipped with these options, do not proceed. Ensure vehicle DOES NOT have SMART KEY.
5. ENSURE THE TILT/TELESCOPIC STEERING WHEEL COLUMN IS FULLY EXTENDED AND LOCKED BEFORE
INSTALLING THIS ACCESSORY.
1. Remove the two (2) #2 phillips screws from the side
of the lower dash fi nish panel.
#2 Phillips Screwdriver
3
1. Remove the lower dash fi nish panel by removing
the two (2) #2 phillips screws from the bottom of
the panel. Using a trim tool, carefully pry outward
to release the two (2) retaining tabs from the side,
as shown in Step 3 and the fi ve (5) pressure clips
from the front of the panel.
2. Disengage the driver’s side kick panel retaining clip
from the lower dash fi nish panel.
3. Remove the OBDII connector from the panel.
4. Disconnect the remaining connectors, if equipped.
#2 Phillips Screwdriver and Trim Tool
4
N
O
T
E
N
O
T
E
KIA Genuine Accessories
Phillips
Screws
Phillips Screws
Pressure
Clips
Fuse Panel
Access Cover
Retaining
Tabs
Pressure Clips
Retaining Clip
Ratchet, 10 mm Socket, Alcohol Cleaner
and Clean Cloth
1
1. Remove and isolate the negative battery cable from
the battery.
2. Using alcohol and a clean cloth, clean the top
surface of the underhood fuse box. Ensure the
surface is completely dry.
3. Remove the backing on the warning label and mount
in place, as shown above.
N
O
T
E
WARNING! Shock Hazard. Do not touch
vehicle’s negative battery terminal to vehicle’s
positive battery terminal. Serious physical
injury or vehicle damage may occur.
!
Goggles
Rubber
Gloves
Fuse Box
Warning Label
Negative
Battery Cable
Revision Date
4/22/2013
Page 5 of 25
1. Remove the fi ve (5) 10 mm bolts and the one (1)
10 mm nut securing the steel knee bolster panel.
2. Remove the steel knee bolster panel from the
vehicle.
Ratchet, Extension and 10 mm Socket
5
1. Remove the three (3) #2 phillips screws securing
the steering column shroud (one (1) underneath
and two (2) behind the steering wheel). Turn the
steering wheel for access.
2. Release the tilt steering wheel adjuster lever.
3. Pull down to separate the lower steering column
shroud (use trim tool, if necessary) and remove
from the vehicle.
6
Phillips
Screws
#2 Phillips Screwdriver and Trim Tool
N
O
T
E
N
O
T
E
KIA Genuine Accessories
10 mm
Bolts
10 mm Nut
1. Carefully pull the weatherstrip away from the driver’s
side “A” pillar.
2. Remove the access cover and the one (1) #2 phillips
screw from the “A” pillar.
Trim Tool and #2 Phillips Screwdriver
7
1. Starting at the top, use a trim tool and remove the
driver’s side “A” pillar trim panel by inserting the
tool behind the panel and prying outward to release
the two (2) pressure clips.
Trim Tool
8
CAUTION! Do not lose the two (2) pressure clips.
Access Cover and Phillips Screw
Pressure Clips
N
O
T
E
N
O
T
E
!
WARNING! Do not damage air bag components.
Revision Date
4/22/2013
Page 6 of 25
10"
9"
9"
9
N
O
T
E
Foam Tape
10” (254 mm)
7” (178 mm)
1. Clean the area of the windshield where the antenna will be mounted with an alcohol cleaner and clean cloth.
Ensure the glass surface is completely dry.
2. Remove protective backing and mount the dipole antenna to the windshield approximately 0.25” (7 mm) below the
mirrors lowest attachment point and/or any windshield electronic gridwork. Press fi rmly to ensure a good glass to
adhesive bond.
Alcohol Cleaner, Clean Cloth and Tape Measure
Goggles
Rubber Gloves
Trim Tool and Tape Measure
10
N
O
T
E
1. Wrap the antenna cable with three (3) pieces of small foam tape, at the distances shown above, to ensure that the
antenna cable will stay in place after routing.
2. Route the antenna cable vertically on the right hand side of the mirror mount up to the headliner. Tuck the cable
behind the headliner and down the “A” pillar, as shown above.
KIA Genuine Accessories
10” (254 mm)
Revision Date
4/22/2013
Page 7 of 25
1. Use four (4) small wire ties to secure the antenna cable to the factory harness located within the “A” pillar, as
shown above. Trim off excess wire ties.
Wire Cutter
11
N
O
T
E
!
KIA Genuine Accessories
Small Wire Ties
Antenna Cable
Air Bag Infl ator
WARNING! Air Bag system interference hazard. DO NOT wrap antenna cable around or secure antenna
cable to any Air Bag components. Damage to the vehicle’s Air Bag system may occur which could result
in serious physical injury.
CAUTION! Ensure the antenna cable is routed away from the Air Bag Infl ator.
CAUTION! If the vehicle is equipped with a sunroof, be careful not to place the wire ties around the drain
tube or the sunroof may not drain properly.
12
CAUTION! Be careful not to bend/damage any of the terminals inside the remote start module.
Antenna Cable
Connector
N
O
T
E
10-Pin
24-Pin
16-Pin
1. Remove the two (2) transmitters and attach individually to each factory key.
2. Route the antenna cable past the left side of the dashboard and over to the dash wall area.
3. Plug the remote start harness 16-pin connector, 24-pin connector, 10-pin connector and the 2-pin antenna cable
connector into the remote start control module before mounting.
4. Ensure all connectors are properly locked into position.
Revision Date
4/22/2013
Page 8 of 25
KIA Genuine Accessories
1. Secure the remote start control module to the factory stud, located on the vehicle dash wall, above the accelerator
pedal assembly with one (1) supplied M6 nut, as shown above.
2. Torque the M6 nut to 14 Nm (1.4 Kgf.m, 10 lb-ft).
Ratchet, Extension, 10 mm Socket and Torque Wrench
13
N
O
T
E
M6 Nut
Torque to 14 Nm (1.4 Kgf.m, 10 lb-ft)
Revision Date
4/22/2013
Page 9 of 25
1. Route the remote start harness 6-pin male and female key-in-sense connectors along the right side of the
steering column to the factory M37 key-in-sense connector.
2. Disconnect the factory female 6-pin M37 key-in-sense connector and plug in the corresponding remote start
harness connectors.
3. Secure the factory female M37 key-in-sense connector and the remote start harness male key-in-sense
connectors to the factory male M37 key-in-sense connector with one (1) small wire tie, as shown above. Trim off
excess wire tie.
1. Route the remote start harness 6-pin male and female ignition connectors along the factory harness up to the
factory M15 ignition switch connector.
2. Disconnect the factory female 6-pin M15 ignition switch connector and plug in the corresponding remote start
harness connectors.
14
N
O
T
E
15
N
O
T
E
WARNING! Engine Stall Hazard. To prevent stress on the remote start wire harness, ensure the tilt/
telescopic steering column is fully extended, if equipped. Ensure all connectors are fully engaged and
locked in place. An engine stall could cause serious physical injury or vehicle damage.
!
Tilt Steering Wheel Release Lever
6-Pin Female Harness Connector
Factory Female M15
Connector
6-Pin Female
Harness Connector
6-Pin Male Harness Connector
KIA Genuine Accessories
Wire Cutter
Small Wire Tie
Factory Female M37
Connector
6-Pin Male Harness Connector
Factory Male
M37 Connector
Revision Date
4/22/2013
Page 10 of 25
Remote Start Harness 4-Pin Female
Connector
16
Wire Cutter
N
O
T
E
1. Route the remote start harness 4-pin male and female brake switch connectors to the brake switch at the top of
the brake pedal, as shown above.
2. Disconnect the factory female 4-pin E41 connector and plug in the corresponding remote start harness
connectors.
3. Secure the factory female 4-pin E41 connector and the remote start harness male connector to the remote start
harness with one (1) large wire tie, as shown above. Trim off excess wire tie.
Factory Female E41 Brake Switch
Connector
Large Wire Tie
KIA Genuine Accessories
MDPS Module
Remote Start Harness 4-Pin Male
Connector
Revision Date
4/22/2013
Page 11 of 25
I/P-N
(MAIN)
I/P-M
(MAIN)
I/P-L
(MAIN)
16
5
17
6
18
7
19
8
12
1
13
2
14
3
15
4
13
5
14
6
15
7
16
8
9
1
10
2
11
3
12
4
20
9
21
10
22
11
18
5
19
6
20
7
21
8
14
1
15
2
16
3
17
4
22
9
23
10
24
11
25
12
26
13
1. Route the Black (Ground) wire and the 26-pin male and female remote start harness connectors (Wrapped
with BLUE tape) along the right side of the fuse panel.
2. Remove the two (2) 10 mm nuts and one (1) 10 mm bolt securing the fuse panel, as shown above.
3. Tilt the fuse panel forward and remove the factory GF01 ground bolt, located to the left of the fuse panel.
4. Position the Black (Ground) wire with ring terminal over the bolt and reinstall.
5. Torque to 14 Nm (1.4 Kgf.m, 10 lb-ft).
6. Route the 26-pin male and female remote start harness connectors (Wrapped with BLUE tape) to the back of
the fuse panel.
7. Locate the 26-pin I/P-L connector on the back of the fuse panel. Disconnect the factory female 26-pin I/P-L
connector and plug in the corresponding remote start harness connectors.
8. Secure the factory female 26-pin I/P-L connector and the remote start harness male connector to the factory
harness with one (1) small wire tie, as shown above. Trim off excess wire tie.
17
Ratchet, Extension, 10 mm Socket, Torque Wrench and Wire Cutter
N
O
T
E
Factory GF01 Ground Bolt
Torque to 14 Nm
(1.4 Kgf.m, 10 lb-ft)
KIA Genuine Accessories
10 mm Nuts
10 mm Bolt
Small Wire Tie
Factory Female 26-Pin
I/P-L Connector
Remote Start Harness 26-Pin Female
Connector
26-Pin I/P-L
Connector
Back of Fuse Panel
Front of Fuse Panel
Ground Wire
Harness Wrapped
with Blue Tape
Revision Date
4/22/2013
Page 12 of 25
21
22
23
24
25
26
31
32
33
34
35
36
3
4
5
6
7
8
12
13
14
15
16
17
27 37
20 30
9 18
2 11
2810 38
191 29
18
Ratchet, Extension, 10 mm Socket, Torque Wrench and Pliers
N
O
T
E
*Refer to Page 3 for T-Tap Installation Procedure.
1. Reinstall the fuse panel with the two (2) 10 mm nuts and one (1) 10 mm bolt, as shown above. Torque 10 mm nuts
and 10 mm bolt to 7 Nm (0.7Kgf.m, 5 lb-ft).
2. Locate the Brown wire in pin #35 of the 38-pin I/P-C female connector.
3. Using pliers, crimp one (1) T-Tap on the Brown wire located in pin #35 of the 38-pin I/P-C female connector.
4. Connect the Brown (Alternator Input) wire from the remote start harness to the Brown wire (Pin #35 of the 38-Pin
I/P-C connector) by engaging the T-Tap. Ensure that the male spade is properly centered in the T-Tap.
CAUTION! Ensure the correct pin location is identifi ed. There may be several wires of the
same/similar color.
*Unplug connector, if necessary, to identify proper pin location and to make T-Tap connection.
KIA Genuine Accessories
38-Pin I/P-C Connector
Alternator Wire
Brown Wire
Pin 35
Terminal End View
10 mm Bolt
Torque to 7 Nm
(0.7 Kgf.m, 5 lb-ft)
10 mm Nuts
Torque to 7 Nm
(0.7 Kgf.m, 5 lb-ft)
38-Pin I/P-C Connector
T-Tap
Revision Date
4/22/2013
Page 13 of 25
19
N
O
T
E
KIA Genuine Accessories
1. Route the 24-pin male and female remote start harness connectors (Wrapped with BLACK tape) along
the front of the fuse panel.
2. Locate the 24-pin I/P-D connector on the front of the fuse panel. Disconnect the factory female 24-pin
I/P-D connector and plug in the corresponding remote start harness connectors, as shown above.
Factory Female 24-Pin I/P-D Connector
Remote Start Harness 24-Pin Female
Connector
I/P-K
(FLOOR)
I/P-D
(FLOOR)
I/P-A
(FLOOR)
I/P-C (MAIN)
I/P-B
(FRONT)
I/P-E (MAIN)
10A
411
512
613
714
7
6
5
4
3
2
17
16
15
14
13
12
21
22
23
24
25
26
31
32
33
34
35
36
3
4
5
6
7
8
12
13
14
15
16
17
27 37
20 30
9 18
2 11
11
10
26
25
24
23
22
21
20
19
929
35
34
33
32
31
30
23
3
2
1
29
28
20
19
16
15
9
8
35
34
22
21
18
17
27
10
2736 8
1828 1
2810 38
191 29
36
30
2431
2532
2633
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
13
12
24
13
25 26
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
21
5
23
6
23
7
24
8
17
1
18
2
19
3
20
4
25
9
26
10
27
11
28
12
29
13
30
14
31
15
32
16
FOG
LAMP RR
10A
MEMORY
25A
P/WDW
LH
25A
P/WDW
RH
15A
S/HEATER
RR
30A
AMP
10A
INTERIOR
LAMP
15A
MULTIMEDIA
25A
SUNROOF 1
30A
DRV
P/SEAT
20A
PAS S
P/SEAT
20A
S/HEATER
FRT
20A
BLOWER
RR
15A
STOP
LAMP
15A
F/LID
20A
DR LOCK
10A
SMART
KEY 4
7.5AMODULE 1
7.5A
SMART
KEY 2
7.5AMDPS
10A
A/BAG
IND
20A
IG1
10A
MODULE 4
7.5A
SMART
KEY 3
10A
MODULE 2
10A
MODULE 3
15A
A/BAG
7.5AMODULE 5
7.5AA/CON
15A
HTD
STRG
25A
SUN
ROOF 2
25A
SMART
KEY 1
10A
HTD
MIRR
7.5ASTART
15A
POWER
OUTLET 1
20A
POWER
OUTLET 2
15A
WIPER
RR
25A
WIPER
FRT
24-Pin I/P-D Connector
Remote Start Harness 24-Pin
Male Connector
Harness Wrapped
with Black Tape
Revision Date
4/22/2013
Page 14 of 25
20
N
O
T
E
KIA Genuine Accessories
1. Route the 26-pin male and female remote start harness connectors (Wrapped with BLACK tape) along the
front of the fuse panel.
2. Locate the 26-pin I/P-K connector on the front of the fuse panel. Disconnect the factory female 26-pin I/P-K
connector and plug in the corresponding remote start harness connectors.
3. Secure the factory female 26-pin I/P-K connector and the remote start harness male connector to the factory
harness with one (1) small wire tie, as shown above. Trim off excess wire tie.
Factory Female 26-Pin
I/P-K Connector
Remote Start Harness 26-Pin Female
Connector
I/P-K
(FLOOR)
I/P-D
(FLOOR)
I/P-A
(FLOOR)
I/P-C (MAIN)
I/P-B
(FRONT)
I/P-E (MAIN)
10A
411
512
613
714
7
6
5
4
3
2
17
16
15
14
13
12
21
22
23
24
25
26
31
32
33
34
35
36
3
4
5
6
7
8
12
13
14
15
16
17
27 37
20 30
9 18
2 11
11
10
26
25
24
23
22
21
20
19
929
35
34
33
32
31
30
23
3
2
1
29
28
20
19
16
15
9
8
35
34
22
21
18
17
27
10
2736 8
1828 1
2810 38
191 29
36
30
2431
2532
2633
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
13
12
24
13
25 26
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
21
5
23
6
23
7
24
8
17
1
18
2
19
3
20
4
25
9
26
10
27
11
28
12
29
13
30
14
31
15
32
16
FOG
LAMP RR
10A
MEMORY
25A
P/WDW
LH
25A
P/WDW
RH
15A
S/HEATER
RR
30A
AMP
10A
INTERIOR
LAMP
15A
MULTIMEDIA
25A
SUNROOF 1
30A
DRV
P/SEAT
20A
PAS S
P/SEAT
20A
S/HEATER
FRT
20A
BLOWER
RR
15A
STOP
LAMP
15A
F/LID
20A
DR LOCK
10A
SMART
KEY 4
7.5AMODULE 1
7.5A
SMART
KEY 2
7.5AMDPS
10A
A/BAG
IND
20A
IG1
10A
MODULE 4
7.5A
SMART
KEY 3
10A
MODULE 2
10A
MODULE 3
15A
A/BAG
7.5AMODULE 5
7.5AA/CON
15A
HTD
STRG
25A
SUN
ROOF 2
25A
SMART
KEY 1
10A
HTD
MIRR
7.5ASTART
15A
POWER
OUTLET 1
20A
POWER
OUTLET 2
15A
WIPER
RR
25A
WIPER
FRT
26-Pin I/P-K Connector
Small Wire Tie
Wire Cutter
Remote Start Harness 26-Pin Male
Connector
Revision Date
4/22/2013
Page 15 of 25
KIA Genuine Accessories
1. Verify all connections are secure as per the installation instructions.
2. Connect the programming button to the corresponding remote start module connector (if disconnected).
3. Secure the programming button and the remote start harness with three (3) small wire ties and four (4) large
wire ties to the factory harness, as shown above. Trim off excess wire ties.
N
O
T
E
21
Wire Cutter
!
Large Wire Ties
WARNING! Engine Stall Hazard. To prevent stress on the remote start wire harness, ensure the tilt/
telescopic steering column is fully extended, if equipped. Ensure all connectors are fully engaged and
locked in place. An engine stall could cause serious physical injury or vehicle damage.
Small Wire Tie
Door Ajar
Module
Small Wire
Ties
Programming Button
Large Wire Tie
Revision Date
4/22/2013
Page 16 of 25
1. Verify all connections are secure as per the installation instructions.
2. Turn the ignition key to the ON position.
3. Reconnect the negative battery cable.
4. Start the vehicle and verify that no air bag or engine codes have been triggered. Any fault codes should be
addressed before proceeding to the next step.
5. Turn the ignition key to the LOCK (OFF) position.
N
O
T
E
22
Ratchet and 10 mm Socket
WARNING! Shock Hazard. Do not touch vehicle’s negative battery terminal to vehicle’s positive battery
terminal. Serious physical injury or vehicle damage may occur.
!
KIA Genuine Accessories
Goggles
Rubber
Gloves
Negative
Battery Cable
Revision Date
4/22/2013
Page 17 of 25
KIA Genuine Accessories
Function Check
Items To Be Checked Results Of The Check
Ensure the transportation fuse is properly installed before performing the Function Check.
If the transmitters fail to operate, refer to Page 23 (Transmitter Programming and Battery Test Procedure).
Remote Engine Start - Make sure the key is
removed from the ignition switch and the doors,
tailgate and engine hood are closed. Activate the
remote start by pressing the start button on the
transmitter two (2) times within three (3) seconds.
The parking lights will fl ash one (1) time, the burglar horn
will beep one (1) time, the doors will lock, then the engine
will crank and start. Once started, the burglar horn will
beep one (1) time and the parking lights will come on and
stay on signifying the engine is running.
Brake Pedal Safety - Enter the vehicle and press
and release the brake pedal.
The engine/remote start will turn off.
Hood Safety Switch - Remove the key from the
ignition and activate the remote engine start. After
the vehicle has started, pull the hood release lever
to release the hood.
The engine/remote start will turn off immediately.
The hood should not have to be lifted to activate the hood
safety switch.
Car Find Feature - Close the tailgate and press the
red car fi nd / panic button on the transmitter.
Repeat this process two (2) times.
Driver’s Door Unlock / Interior Lamp - Press the
start button on the transmitter one (1) time to
unlock the driver’s door.
The parking lights will fl ash two (2) times, unlock the
driver’s door only and illuminate the interior light for thirty
(30) seconds.
The parking lights will fl ash two (2) times and unlock all
doors.
Door Unlock - Close the engine hood and all doors
and activate the remote engine start.
Press the start button on the transmitter two (2)
times within fi ve (5) seconds.
The engine/remote start will turn off and the head lights will
remain on for approximately fi fteen (15) seconds. Ensure
the head lights turn off after fi fteen (15) seconds.
Quick Stop Feature - Enter the vehicle, and close
all doors. Start the vehicle with the ignition key.
With the vehicle in park and foot off the brake
pedal, press the start button on the transmitter one
(1) time. Remove the key from the ignition and
turn on the head lights using the switch.
Remote Engine Stop - Press and hold the start
button on the transmitter for three (3) seconds.
Tailgate Safety Switch - Open the tailgate using the
release inside the vehicle.
The engine/remote start will turn off immediately.
Panic Feature - Press and hold the red car fi nd /
panic button on the transmitter for three (3) seconds
to activate. Press the red car fi nd / panic button a
second time to deactivate.
The parking lights will fl ash and the burglar horn will
beep for up to thirty (30) seconds.
The parking lights will fl ash and the burglar horn will beep
fi ve (5) times. Subsequent presses within fi ve (5) seconds
of the fi rst press will beep the burglar horn slightly louder.
NOTES: Interior lamp switch must be set to door
position to illuminate.
If no door or tailgate is opened within thirty (30)
seconds, the interior lights will turn off and the
doors will auto lock.
The head lights will remain on for the entire fi fteen (15)
minute run time.
Verify that the parking lights turn on and that the vehicle
remains running. The driver’s door only will unlock (if
previously locked).
NOTE: If no door or tailgate is opened within thirty (30)
seconds, the interior lights will turn off and the
doors will auto lock.
Key-In-Sense - Insert the ignition key into the igni-
tion switch but keep it in the OFF position. Activate
the remote engine start using the transmitter.
The parking lights will fl ash one (1) time and the ignition
will turn on as if it is going to start. The burglar horn will
beep two (2) times and the remote engine start will not
attempt to start the vehicle since it detects the key in the
ignition. In addition, the driver’s door will unlock and the
vehicle’s interior light will illuminate.
NOTE: Interior lamp switch must be set to door
position to illuminate.
Revision Date
4/22/2013
Page 18 of 25
Phillips
Screws
1. Reinstall the fi ve (5) 10 mm bolts and one (1) 10
mm nut securing the steel knee bolster panel.
Torque bolts to 14 Nm (1.4 Kgf.m, 10 lb-ft).
Ratchet, Extension, 10 mm Socket and
Torque Wrench
26
N
O
T
E
KIA Genuine Accessories
25
N
O
T
E
1. Reinstall the lower steering column shroud around
the steering column.
2. Reinstall the three (3) #2 phillips screws securing
the steering column shroud (one (1) underneath
and two (2) behind the steering wheel), as shown
above. Turn the steering wheel for access.**
**NOTE: To access screw mounting locations, insert
key and turn to the ACC position, in order to prevent
the steering wheel from locking.
#2 Phillips Screwdriver
Use care when securing the steering column
shroud to avoid misalignment, which could
cause unwanted noises when turning the
steering wheel.
1. Reinstall the driver’s side “A” pillar trim by engaging
the two (2) pressure clips.
23
Pressure Clips
N
O
T
E
CAUTION! Do not lose the two (2) pressure
clips.
10 mm Nut
Torque to 14 Nm
(1.4 Kgf.m, 10 lb-ft)
10 mm Bolts
Torque to 14 Nm
(1.4 Kgf.m, 10 lb-ft)
1. Reinstall the one (1) #2 phillips screw and the access
cover.
2. Reinstall the weatherstrip near the driver’s side “A”
pillar.
24
Access Cover and
Phillips Screw
#2 Phillips Screwdriver
N
O
T
E
Revision Date
4/22/2013
Page 19 of 25
1. Reinstall any connectors, including the OBDII connector that may have been removed from the lower dash fi nish
panel.
2. Reinstall the lower dash fi nish panel by engaging the fi ve (5) pressure clips, two (2) retaining tabs, four (4)
#2 phillips screws and the driver’s side kick panel retaining clip.
#2 Phillips Screwdriver
27
N
O
T
E
WARNING! Engine Stall Hazard. To prevent stress on the remote start wire harness, ensure the tilt/
telescopic steering column is fully extended, if equipped. Ensure all connectors are fully engaged and
locked in place. An engine stall could cause serious physical injury or vehicle damage.
!
28
N
O
T
E
1. Reinstall the driver’s side dash end cap by engaging
the four (4) pressure clips.
2. Reinstall the fuse panel access cover.
KIA Genuine Accessories
Phillips
Screws
Phillips
Screws
Pressure Clips
Pressure
Clips
Fuse Panel
Access Cover
29
1. Place the Owner’s Guide and the Quick Reference
Guide into the vehicle’s glove box.
N
O
T
E
Owner’s Guide
&
Quick Reference Guide
Retaining
Tabs
Retaining Clip
Revision Date
4/22/2013
Page 20 of 25
Accessing the DNA Card
1
2
1
2
*Verify that both rows of multi-pin connectors are aligned
and seated properly.
Correct Fuse and Jumper Positions
KIA Genuine Accessories
Troubleshooting
HVAC 1
HVAC 2
MAIN B+
IGN
DOME LIGHT
PK LIGHTS
DOOR LOCKS
DR DOOR/TRNK REL
- +
- +
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25

KIA 1U056 ADU00 Installation Instructions Manual

KIA
Brand
KIA
Model
1U056 ADU00
Type
Installation Instructions Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents