The Delfield Company, 980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2002 The Delfield Company. All rights reserved. Printed in U.S.A.
PROJECT
ITEM #
QUANTITY DATE
APPROVAL
403
Self-contained compact work top freezers
The refrigeration system on this
equipment uses HFC--404A refrigerant.
Short form specications
Exterior top shall be one-piece, 22-gauge stainless steel with front edge turned down
to form nosing and rear edge turned up to form a 2" (5.1 cm) thick by 4" (10.2 cm) high
backsplash.
Exterior back and bottom shall be one-piece 24-gauge galvanized metal. Exterior ends
shall be 22-gauge stainless steel.
Base interior shall be one-piece thermoformed ABS plastic material, with integral shelf
supports. Base shall be fully insulated with high-density foamed-in-place polyurethane.
Refrigeration system shall use HFC-404A refrigerant. Compressor shall be ¢ h.p., with
condenser coil and hot gas condensate evaporator mounted on rear of cabinet. Evapora-
tor coil and temperature control shall be mounted on the interior rear wall of the cabinet.
Refrigerant ow shall be controlled by a capillary tube. Cabinet shall maintain
–5°F to 0°F (–21°C to –18°C) interior cabinet temperature.
Electrical connections shall be 115 volt, 60 Hertz, single phase. Unit shall have a 7' (2.1
m) long electrical cord and NEMA 5-15P plug. Cord and plug shall be located on rear of
cabinet, centered left to right, 16" (40.6 cm) above oor.
Equipment shall be mounted on 6" (15.2 cm) high metal legs with black enamel nish.
THE FOLLOWING APPLIES TO MODEL 403 (SINGLE DOOR) ONLY:
Doors shall have a 22-gauge stainless steel exterior, with a thermoformed ABS plastic
interior liner, and shall be fully insulated with foamed-in-place polyurethane. Door
handles shall be black, recessed and shall extend the full length of the top of the door.
Cabinet shall have (2) adjustable epoxy-coated wire shelves installed.
Optional accessories & modications
Stainless steel back
Plastic laminate on front
Additional wire shelves
Stainless steel single-tier overshelf
3.5" (8.9 cm) diameter casters
5" (12.7 cm) diameter casters
Door lock
Full-size composite-type cutting top
220 volt, 50 Hertz electrical system
Model 403
The Delfield Company, 980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2002 The Delfield Company. All rights reserved. Printed in U.S.A.
DS403 02/01
Self-contained compact work top freezers
403
39.50"
100.3 cm
4.00"
10.2 cm
28.50"
72.4 cm
2.00"
5.1 cm
35.50"
90.2 cm
6.00"
15.2 cm
19.50"
49.5 cm
17.00"
43.2 cm
BULLET FEET CAN
ADJUST UPWARDS ONLY,
UP TO+1.00"/2.5 cm
1.00"/2.5 cm
RUBBER
BUMPER
INTERIOR CLEAR DIMENSION,
LEFT TO RIGHT: 21.25"/54.0 cm
A
B
C
D
E
SHELF SUPPORT
SPACING
A = 7.50"/19.1 cm
B = 4.00"/10.2 cm
C = 3.75"/9.5 cm
D = 2.75"/7.0 cm
E = 6.00"/15.2 cm
24.75"
62.9 cm
STANDARD DOOR HINGING IS ON RIGHT
HINGING MAY BE REVERSED AT INSTALLATION
INSTALLATION NOTE:
Refrigeration system is designed
so that air will ow under the unit,
through the compressor area, and
out the top rear of the unit. Any
restriction to this air ow path will
void the warranties.
ELEVATION VIEW
MODEL 403
PLAN VIEW MODEL 403
DOOR CLEARANCE DETAIL
MODEL 403
FRZR.
27.25"
69.2 cm
39.50"
100.3 cm
27.25"
69.2 cm
28.50"
72.4 cm
MODEL
NUMBER
NUMBER
OF
SHELVES
SHELF
AREA
STORAGE
CAPACITY*
SHIP
WEIGHT
HORSE-
POWER
VOLTS/
HERTZ/
PHASE AMPS
NEMA
PLUG
403
2
7.2 ft
0.67 m
5.7 ft
0.16 m
184 lbs
84 kg 115/60/1 5.0 5-15P
* STORAGE CAPACITY FOR DRAWER-BASE MODEL IS SHOWN FOR EACH DRAWER; MULTIPLY BY 2 TO OBTAIN TOTAL STORAGE CAPACITY
1/4
-
1
-
2
