GE ECSA Installation guide

Canopy Light, Surface & Recessed (ECSA)

Evolve

™

LED Area Light

GE

Lighting

Installation Guide

GEH-6020

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation. This Class [A] RFLD complies with the Cana-

dian standard ICES-003. Ce DEFR de la classe [A] est conforme à la NMB-003 du

Canada.

Note: This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the

interference at his own expense.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

Save these instructions for future use.

WARNING

Risk of electrical shock. Disconnect power before servicing

or installing product.

CAUTION

Risk of injury. Wear safety glasses and gloves during

installation and servicing.

WARNING

Risk of injury or damage. Unit will fall if not installed

properly. Follow installation instructions.

imagination at work

WARNING

This product must be installed in accordance with the

applicable installation code by a person familiar with

the construction and operation of the product and the

hazards involved.

• This luminaire is designed for outdoor lighting service,

and should not be used in areas of limited ventilation,

or in high ambient temperatures.

• Best results will be obtained if installed and

maintained according to the following

recommendations.

• Luminaire is designed to operate in typical

temperatures at 25°C and to be mounted horizontally

with LEDs facing down, as shown.

SPECIFICATIONS

• Weight: Maximum weight 13.2 lbs. (6 kg)

• IP Rating: Wet Location (IP65 for optical)

Recessed

Surface Mount

FIGURE 4

FIGURE 5

MOUNTING

3

WARNING

Risk of injury or damage. Unit will fall if not installed

properly. Follow installation instructions.

HANDLING

2

• This luminaire has been properly packed so that no

parts should have been damaged during transit.

• Inspect to conrm.

• The mounting bracket is shipped in a separate box.

• Damage may occur if luminaire is improperly handled

outside of pack.

• Do not impact or stack luminaire after removal from

packaging.

UNPACKING

1

1. Drill 4 3/8” mount holes for dimensions in ceiling to

mount xture. If the size of open hole of ceiling is less

than

1”, then enlarge the open hole to 1”. Please refer

to the

mounting template. (See Fig.3)

2. Clean all areas that will be sealed.

B. Liberally apply RTV sealant where the holes were

drilled and around the large center hole on both sides

of the gasket. Place the big gasket on the top of the

holes. (See Fig.4))

C. Place pre-installed plate bracket on the gasket.

(See Fig.5)

FIGURE 3

D. RTV caulk around the plate bracket and all fasteners

to ensure waterproong of luminaire. (See Fig.6)

FIGURE 6

DRILL 3/8”

A. Pre-installation

Surface Mount

E. Let one side of SJOW cable wire pass through hole

using a waterproof sleeve to connect to existing power

line in existing terminal box. Tighten the nut of

waterproof sleeve. (See Fig. 7)

FIGURE 7

FIGURE 10, 11 & 12

FIGURE 12

H. Tilt the luminaire and insert it into the mount box

tting. Use 3M 314 waterproof connectors to connect

power cable from luminaire where Black is Line,

White is Neutral and green is ground to SJOW cable wire.

(See Fig.10, 11)

I. Lift and push luminaire up to mount box.

Fasten 2 M4 to secure luminaire with mount box.

(Fig. 11 & Fig. 12)

FIGURE 13

G. From under the structure fasten 4pcs M8 nut lock

washer and washer to x mount box with ceiling

and plate bracket. Torque top and bottom bolts to

25 - 32 ft-lbs (34-43 N-m). (See Fig.9)

FIGURE 9

Recessed Installation

Stud

F. Tighten the screw (4-M4) to assemble junction box

with plate bracket. Torque reference 2.1ft-lbs

(2.9 N-m). (See Fig. 8)

1. Cut a square hole on Ceiling. Additional studs may

be required to xed on ceiling rib.

Hole size: 12”x 12”/ 16” X 16”

2. Mount the light housing and secure to the studs.

The light housing mounting hole are sized for ¼”

diameter screw.

Light Housing

3. Open the junction Box cover. Make necessary supply

wiring connections to supplied power cords using

appropriate wire connectors.

Junction Box

4. Lift the luminaire up to the light housing. Assemble

luminaire and light housing using 4 pcs M4 screws

(provided).

Light Housing

Luminaire

Notes :

• This product must be installed in accordance with

applicable local, state, and national electrical codes

by a licensed person familiar with the construction

and operation of the product and hazards involved.

• This luminaire must adequately grounded for

protection against shock hazards and to assure

proper operation.

• Make sure all electrical power is turned o while

installing the xture.

• If the supply cord is damaged, it must be replaced by

the manufacturer or its service agent or a similar

qualied person in order to avoid a hazard.

• The structure of Installation of this lighting needs to

aord load of 16 pounds. To avoid Lamp fall.

• Lamps recommended installation height of 16 feet or

above.

PRODUCT DIMENSIONS

4

Surface Mount

9.84 in.

11.81 in.

BOTTOM VIEW

SIDE VIEW

5.75 in.

ACCESSORY COMPONENTS LIST

5

Recessed Installation

Drawing Name Qty.

Plate bracket 1 pc

3M Terminal 3 pcs

Surface Mount

11.1”

14” / 18”

7.1”

8.8”

14” / 18”

7.1 in.

14” / 18”

8.8 in.

35-201578-212 (Rev 12/11/13)

English

These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in

connection with installation, operation or maintenance. Should further information be desired or should particular problems arise which are not

covered suciently for the purchaser’s purposes, the matter should be referred to GE Lighting.

GE Lighting • 1-888-MY-GE-LED (1 - 888 - 69 - 43 - 533) • www.gelighting.com

Evolve and the GE brand and logo are trademarks of the General Electric Company.

Recessed Installation

Light stands Accessories Type (Optional)

Spec (inches) Schematic diagram Accessories

Items

Accessories

12” 14 x 14 x 2 1/4” screws x 4

Light Housing X1

M4 screw 4 X 4 (incl)

Accessories

16” 18 x 18 x 2 1/4” screws x 4

Light Housing X1

M4 screw 4 X 4 (incl)

Accessories

16” 16 x 16 1/4” screws x 4

Eschutcheon Plate X1

M4 screw 4 X 4 (incl)

Accessories

32” 32 x 32 1/4” screws x 4

Eschutcheon Plate X1

M4 screw 4 X 4 (incl)

Page is loading ...

LISTA DE COMPONENTES AUXILIARES

5

Instalación empotrada

Plano Nombre Cant.

Soporte de chapa 1

Terminal 3M 3

Montaje en supercie

11.1”

14” / 18”

7.1”

8.8”

14” / 18”

7.1 pulg.

14 pulg. / 18 pulg.

8.8

pulg.

Page is loading ...

GE ECSA Installation guide

GE ECSA Installation guide

in other languages

Related papers

Other documents