Explore Scientific WSC4009 Owner's manual

Brand: Explore Scientific

Model: WSC4009

Category: Alarm clocks

Type: Owner's manual

This manual is also suitable for

mode light mem

ICE ALERT

sensor

on off

INSTRUCTION MANUAL

...............2

ISTRUZIONI PER L’USO

.............. 16

BEDIENUNGSANLEITUNG

.......... 30

MODE D‘EMPLOI

....................... 44

MANUAL DE INSTRUCCIONES

.... 58

Art.No.: WSC4009/WSH4009

TOUCH KEY WEATHER STATION

STAZIONE METEO CON PULSANTI TATTILI

WETTERSTATION MIT BERüHRUNGSTASTEN

BOUTON DE STATION CLIMATIQUE

ESTACIóN METEOROLóGICA DE BOTONES TáCTILES

*Radio-controlled clock function not available in every territory / Funzione di orologio radiocontrollati non disponibile in ogni territorio / Funkuhrfunktion nicht in jederm Gebiet verfÿbar / La fonction

dÿorloge radio-pilot?nÿst pas disponible dans tous les territoires / La funciÿ de reloj radiocontrolado no est?disponible en todos los territorios

mode light mem

ICE ALERT

sensor

on off

ABOUT

THIS INSTRUCTION

MANUAL

Thes

e operating instructions are to be considered

a component of the device.

Please read the safety instructions and the operating

instructions carefully before use.

Keep these instructions for renewed use at a later date.

When the device is sold or given to someone else, the

instruction manual must be provided to the new owner/

user of the product. The device is intended only for

indoor use.

GENERAL W

ARNINGS

• Risk of electric shock — This de

vice contains

electronic components. Only use the device as

described in the manual; otherwise, you run the

risk of an electric shock.

•

Choking hazard

— Children should only use the

device under adult supervision. Keep packaging

material, like plastic bags and rubber bands, out

of the reach of children, as these materials pose a

choking hazard.

•

Risk of chemical burn — Keep batteries out of the

each of children! Make sure you insert the bat-

teries correctly. Leaking battery acid can lead to

chemical burns. Avoid contact of battery acid with

skin, eyes and mucous membranes. In the event

of contact, rinse the affected region immediately

with a plenty of water and seek medical attention.

•

Risk of

re/explosion — Do not expose the device

to high temperatures. Use only the recommended

batteries. Do not short-circuit the device or batter-

ies, or throw them into a �e. Excessive heat or im-

proper handling could trigger a short-circuit, a �e,

or an explosion.

•

Do not

disassemble the device. In the event of a

defect, please contact your dealer. The dealer will

contact the Service Centre and can send the de-

vice in to be repaired, if necessary.

•

Use only

the recommended batteries. Always re-

place weak or empty batteries with a new, com-

plete set of batteries at full capacity. Do not use

batteries from different brands or with different

capacities. The batteries should be removed from

the unit if it has not been used for a long time.

SCOPE OF DELIVERY

WSC4009

Weather station, Outdoor sensor, Operating instructions,

AC/DC adapter(3.6V)

WSH4009

Weather station, Outdoor sensor, Operating instructions.

BEFORE YOU BEGIN

• We recommend using alkaline batteries. If temper-

atures regularly fall below 0°C (32°F), we recom-

mend using lithium batteries.

• Avoid using rechargeable batteries. (Rechargeable

batteries cannot maintain correct power require-

ments.)

•

ity in the battery compartment. 2x AA Batteries are

required for the Weather station and 2x AAA Batter-

ies are required for the Outdoor sensor.

PRODUCT OVERVIEW

1. When connect with batteries, press [ light ] to

activate the backlight for 5 seconds or to acti-

vate the snooze function to delay the alarm by

8 minutes. When commect with adaptor, press

the [ light ] button to adjust the brightness.The

setting order: High light --->Low--->light--->off.

2. Press [ mode ] to switch between time, date,

alarm 1 and alarm 2 display.

3. While in setting mode, press [ ] to increase

one unit, press and hold to increase rapidly.

4. While in setting mode, press [ ] to decrease

one unit, press and hold to decrease rapidly.

5. Press [ ] to toggle the display among

current, maximum and minimum recording of

temperature/humidity. Press and hold to clear

the max/min memory records.

6. ICE ALERT Alarm Led.

*Radio-controlled clock function not available in every territory

12 5

3 46

mode light mem

ICE ALERT

sensor

on off

7. Air vent

8. Battery compartment

9. Power jack(For WSC4009 only)

(Input 3.6V DC )

OUTDOOR SENSOR

1. Outdoor temperature & humidity LCD display

2. Battery compartment

3. TX (Initiate main unit search)

4. Channel switch

C/F switch

Reset

AA 1.5V LR6 / R6

DC3.6V

BUTTON

MODE

men

Standard mode

PRESS

Adjust brightness

when connect

with adapter

Toggle the display among current,

maximum and minimum recording

of temperature/humidity

HOLD

Enter into time

and date setting

Clear the max/min memory records

Time/alarm

setting mode

PRESS Confirm setting Increase Decrease

_______

HOLD

_______

Quick

Increase

Quick

Decrease

_______

light

mode

HOLD

Alarm mode

PRESS

Turn RCC

on/off

Turn RCC

on/off

Turn on backlight

for 8 seconds

Switch time,

alarm display

Enter into time

and date setting

Switch time,

alarm display

Toggle between

outdoor sensor

chammel 1-3

Initiate RCC

receiving

Toggle between

outdoor sensor

chammel 1-3

Initiate RCC

receiving

Turn Alarm

on/off

_______

Turn Alarm

on/off

_______

Clear the max/min memory records

Toggle the display among current,

maximum and minimum recording

of temperature/humidity

Turn on backlight

for 8 seconds

Adjust brightness

when connect

with adapter

LCD DISPLAY

1. Weather Forecast symbols

2. Indoor Temperature

and Indoor humidity display

3. Outdoor Temperature

and Outdoor humidity display

4. Time/Alarm display

5. Phase of the moon

[

] Low battery indicator

[

] RF & Outdoor channel indicator

[

] Time zone indicator

6. Comfort level

[ ] Alarm indicator

(A1:1-5 Weekday, A2: 6-7 weekend)

tor[ ] RCC signal indica

[ ] Max/Min temperature

humidity indicator

[ ] Daylight saving time

[ ] trend of temperature and humidity

[ ] Time zone(For US only)

GETTING STARTED

INSERT BATTERIES

1. Remove the battery door from the back.

2. Insert 2x AA (LR6)/1.5V batteries. Please ensure

the polarities (+/-) of the batteries match upon in-

stallation.

3. Reattach the battery door.

NOTE: Replace batteries when [

] displays, or

when the display is dim.

OUTDOOR SENSOR

The main unit can receive data from up to 3 outdoor

sensors. 1 Sensor is included with delivery.

1. Remove the battery door from the back.

3. Select a channel, then press TX.

2. Insert 2x AAA (LR03)/1.5V batteries. Please ensure

the polarities (+/-) of the batteries match upon in-

stallation.

4. Reattach the battery door.

5. Place the sensor within 30 m (98 ft) of the main unit

using the table stand or wall mount.

TO SEARCH FOR A SENSOR:

The main unit will automatically search for a new sen-

sor after the batteries are installed. To manually initi-

ate a outdoor sensor search, press and hold [ ].

NOTE: The transmission range may vary depending

on many factors. You may need to experiment with

various locations to get the best results.

CLOCK

CLOCK RECEPTION

1. When you insert or replace the batteries, RCC recep-

tion is initiated. To manually start RCC reception

press the [ ] button.

2. The receiving process duration is 3 minutes.

3. During receivin

g process, the RCC signal symbol

shows:

[ ]

4. If the RCC receiving process is successful, a com-

pleted RCC symbol [ ] will be shown in the display

and the date and time will be set automatically. If it

fails within 7 minutes, RCC setting will quit automati-

cally. If that happens, press and hold the [ ] but-

ton to re-initiate RCC receiving.

SET THE CLOCK MANUALLY

1. Press and hold[ ]button to enter into time and

date setting.

2. The setting parameter will flash.

3. Press [ ] button once, the figure will increase 1

unit. Press and hold the [ ] button, the figures

will increase rapidly.

4. Press [ ] button once, the figure will decrease 1

unit. Press and hold the [ ] button, the figures

will decrease rapidly.

5. Press [

]

button to confirm setting and enter to

next parameter.

6. Sequence of setting: Time zone ---> 12/24h format

Hour Minute Year Calendar format (day-

month/month-day) Month Day Temperature

unit (°C/°F) DST ON/OFF(only for US) Exit

7. If there is no action in 20 seconds, the setting will be

saved and you

will exit the setting mode.

mode

--->

---> ---> --->

--->

ALARM

SETTING/ADJUSTING ALARM TIME

1. Press [ ] to display the alarm.

2. Press and hold [ ] button to enter alarm

setting mode.

3. The setting parameter will flash.

4. Press [ ] or [ ] button to set the desired data.

5. Press [ ] button to confirm setting and exit.

6. Alarm will turn on automatically when alarm setting

is finished.

TURN ON/OFF ALARM

Press the [ ] button to turn on/off the alarm.

OPERATION

1. At the set time, alarm signal rings.

2. During the alarm, press the [ ] button to delay

the alarm by 8 minutes.

3. If you do not press any button to stop the alarm, it

will automatically turn off after 2 minutes.

4. To stop the alarm, press any other button, except

for

5. The alarm will start again at the next alarm time,

unless y

ou switch off the alarm function by press-

ing the [ ] button until the alarm is set to off.

WEATHER FORECAST

This device forecasts the next 12-24 hours of weather

within a 30-50 km (19-31 mile) radius with a 75% ac-

cuarcy.

SYMBOL DESCRIPTION

Sunny

Sunny to cloudy

Cloudy

Cloudy to rain

Cloudy to snow

mode

In normal mode:

[ ].

ICE ALERT

If the channel 1 sensor falls between 3°C to -2°C

(37°F to 28°F), the ice alert indicator [ ] will dis-

play, and will disappear once the temperature is out

of this range.

TEMPERATURE AND HUMIDITY

The indoor temperature is always displayed in the right

corner of the screen. To receive outdoor temperature

you can connect up to 3 outdoor sensors to the main

unit.

Press the [ ] button to toggle between Channel 1-3.

MAX/MIN MEMORY

To toggle between current, minimum and maximum

records for the selected sensor press [ ] repeat-

edly. To clear records, press and hold [ ].

NOTE: When the indoor temperature is lower than -5 °C

(23.0 °F), the screen displays LL.L.

When the tempera-

ture is higher than 50 °C (122.0 °F), the screen displays

HH.H.

BACKLIGHT

When connect with batteries, press [ light ] to activate

backlight for 5 seconds. When connect with adaptor,

press the [ light ] button to adjust the brightness. The

setting order: High light ---> Low light ---> off.

SPECIFICATIONS

MAIN UNIT:

Dimensions

100 x 49.3 x 185 mm (L x W x H)

Weight

280 g (Exclude batteries)

Power:

2x AA (LR6) 1.5V batteries

TEMPERATURE:

Indoor temperature display range:

-5°C to +50°C (23°F to 122°F)

Outdoor temperature display range:

-20°C to +60°C (-4°F to 140°F)

HUMIDITY:

Indoor/outdoor humidity range:

20% - 95% RH

Accuracy:

+/- 5% (40%-80%), other +/-7%

OUTDOOR SENSOR:

Dimensions:

60 x 20 x 60 mm (L x W x H)

Weight:

45 g (Exclude batteries)

Transmission range:

30 m (98 ft)

Temperature range:

-20°C to 60°C (-4°F to 140°F)

Signal frequency:

433 MHz

Power:

2x AAA (LR03) 1.5V batteries

AC/DC POWER ADAPTER:

Only use a compatible AC/DC Power adapter

(3.6V 100mA). Plug the power cable to

the power jack and the power adapter to a

suitable power outlet.

EC DECLARATION OF CONFORMITY

Hereby, Explore Scientific GmbH declares

that the equipment type with part number:

WSC4009,WSH4009 are in compliance with

Directive: 2014/53/EU. The full text of the EU declaration

of conformity is available at the following internet address:

www.bresser.de/download/WSC4009/CE/WSC4009_CE.pdf

www.bresser.de/download/WSH4009/CE/WSH4009_CE.pdf

RCM DECLARATION OF CONFORMITY

The product complies with electrical

safety, EMC and radio spectrum regulatory

requirements for products supplied to the

Australia or New Zealand market.

NOTES ON CLEANING

• Remove the batteries before cleaning.

• Only use a dry cloth to clean the exterior of the

device. To avoid damaging the electronics, do not

• Protect the device from dust and moisture.

DISPOSAL

Dispose of the packaging materials properly,

according to their type, such as paper or card-

board. Contact your local waste-disposal ser-

vice or environmental authority for information on the

proper disposal.

Do not dispose of electronic devices in the

household garbage!

As per the Directive 2002/96/EC of the Euro-

pean Parliament on waste electrical and electronic

equipment and its adaptation into German law, used

electronic devices must be collected separately and

recycled in an environmentally friendly manner.

CAUTION

– Risk of explosion if the battery is replaced by an

incorrect type

– disposal of a battery into fire or a hot oven, or me-

chanically crushing or cutting of a battery, that can

result in an explosion;

– leaving a battery in an extremely high temperature

surrounding environment that can result in an ex-

plosion or the leakage of flammable liquid or gas;

– a battery subjected to extremely low air pressure

that may result in an explosion or the leakage of

flammable liquid or gas.

¹ ² ³

battery contains cadmium

battery contains mercury

battery contains lead

WARRANTY & SERVICE

The regular guarantee period is 2 years and begins

voluntary guarantee period as stated on the gift box,

registration on our website is required.

You can consult the full guarantee terms as well

as information on extending the guarantee period

and details of our services at www.bresser.de/

warranty_terms.

Would you like detailed instructions for this product

in a particular language? Then visit our website via

the link below (QR code) for available versions.

Alternatively you can also send an email to

manuals@bresser.de or leave a message on +49 (0)

28 72 – 80 74-220*. Please always state your name,

precise address, a valid phone number and email

address, as well as the article number and name.

*Number charged at local rates in Germany (the amount

you will be charged per phone call will depend on the tariff

of your phone provider); calls from abroad will involve

higher costs.

www.bresser.de/warranty_terms

MANUAL DOWNLOAD:

www.bresser.de/download/WSC4009

www.bresser.de/download/WSH4009

SERVICE AND WARRANTY:

In accordance with the regulations concern-

ing batteries and rechargeable batteries, dis-

posing of them in the normal household

waste is explicitly forbidden. Please make sure to

dispose of your used batteries as required by law — at

a local collection point or in the retail market. Dis-

posal in domestic waste violates the Battery Direc-

tive. Batteries that contain toxins are marked with a sign

and a chemical symbol.

INFORMAZIONI SUL MANUALE DI

ISTRUZIONI

Il presente manuale è parte integrante del prodot-

to.

Non azionare il dispositiv

o prima di aver letto attenta-

mente le istruzioni di sicurezza e le istruzioni per l'uso

in esso contenute.

Il manuale deve essere conservato in modo che sia

possibile consultarlo anche in seguito. Nel caso in cui il

dispositivo venga venduto o ceduto a terzi, dovrà essere

fornito al nuovo possessore del dispositivo. Il disposi-

tivo può essere utilizzato esclusivamente in ambienti

interni.

AVVERTENZE GENERALI

• RISCHIO DI FOLGORAZIONE — Questo apparec-

chio contiene componenti elettronici azionati da

una sorgente di corrente (alimentatore e/o batte-

rie). L’utilizzo deve avvenire in stretta conformità

con quanto prescritto nel presente manuale. In

caso contrario, non sarà possibile escludere il ri-

schio di infortuni elettrici.

• PERICOLO DI SOFFOCAMENTO — I bambini pos-

sono

utilizzare il dispositivo solo sotto la vigilanza

di un adulto. I materiali di imballaggio, i sacchetti

di plastica e le fasce in gomma possono causare

soffocamento e, pertanto, devono essere conser-

vati in modo che i bambini non riescano a raggiun-

gerli.

• RISCHIO DI USTIONE CHIMICA — Tenere le bat-

terie fuori dalla portata dei bambini. Accertarsi di

installare le batterie nel modo corretto. La fuoriu-

scita di acido dalle batterie può causare ustioni

chimiche. Evitare che l’acido venga a contatto con

pelle, occhi e mucose. In caso, lavare immedia-

tamente le parti interessate con un’abbondante

quantità di acqua e rivolgersi a un medico.

• RISCHIO DI INCENDIO/ESPLOSIONE — Non

esporre il dispositivo a temperature elevate. Utiliz-

zare solo le batterie consigliate. Evitare che pos-

tivo o delle batterie. Non gettare il dispositiv

o o le

batterie nel fuoco. Il surriscaldamento o l’impiego

inappropriato potrebbe generare un cortocircuito,

un incendio o un'esplosione.

• Non smontare il dispositivo. Qualora dovesse ri-

levarsi difettoso, rivolgersi al proprio rivenditore

autorizzato. Il rivenditore provvederà a contattare

il Centro assistenza e, se necessario, spedirà il di-

spositivo in riparazione.

• Utilizzare solo le batterie consigliate. Le batterie

scariche o esaurite devono essere sempre sostituite

con una serie completa di batterie nuove di capacità

massima. Non utilizzare batterie di marche o capaci-

tà diverse. Rimuovere le batterie dall’unità se questa

rimarrà inutilizzata per un periodo prolungato.

ACCESSORI IN DOTAZIONE

WSC4009

Stazione meteo, sensore per esterni, istruzioni per

l’uso, Adattatore CC 3.6V 150mA.

WSH4009

Stazione meteo, sensore per esterni, istruzioni per

l’uso.

PRIMA DI INIZIARE

• Si consiglia l'uso di batterie alcaline. Se le tempe-

rature tendono regolarmente a scendere sotto 0 °C

(32 °F), tuttavia, potrebbe essere preferibile l’impie-

go di batterie al litio.

• Evitare di utilizzare batterie ricaricabili (le batterie

ricaricabili non soddisfano i requisiti di alimenta-

zione appropriati).

• Al primo utilizzo, avere cura di inserire le batterie in

modo da rispettare la polarità indicata nel relativo

vano. Sono necessarie due batterie AA per la sta-

zione meteo e due batterie AAA per il sensore per

esterni.

INFORMAZIONI GENERALI SUL

PRODOTTO

Quando l'unità è alimentata a batterie, premere

[ light ] per attivare la retroilluminazione per 5

secondi o per attivare lo snooze e ritardare la

sveglia di 8 minuti. Quando l'unità è collegata

all'adattatore, premere il pulsante [ light ] per reg-

olare la luminosità. Sequenza di impostazione:

Alta luminosità —> Bassa luminosità —> Spento.

3. In modalità impostazione, premere il tasto [ ]

per aumentare il valore di una unità; tenerlo pre-

muto per incrementare il valore rapidamente.

4. In modalità impostazione, premere il tasto [ ]

per ridurre il valore di una unità; tenerlo premu-

to per decrementare il valore rapidamente.

5. Premere [ ] per visualizzare alternati-

vamente i record dei valori di temperatura/

umidità corrente, massima e minima. Tenere

premuto per cancellare dalla memoria i record

relativi ai valori di massima/minima.

6. Orologio

sveglia LED con ICE ALERT

(ALLERTA GHIACCIO)

12 5

3 46

mode light mem

ICE ALERT

sensor

on off

Premere [mode] per alternare la visualizzazione

di ora, data, sveglia 1 e sveglia 2. Premere e

tenere premuto [ mode ] per accedere all’imp-

ostazione dell’ora e della data.

8. Vano batterie

9. Presa di alimentazione(Solo per WSC4009)

(ingresso 3,6VCC)

SENSORE PER ESTERNI

1. Display LED con temperatura e umidità esterne

2. Vano batterie

3. TX (avvio della ricerca dell’unità principale)

4. Interruttore per il canale

*Funzione di orologio radiocontrollati non disponibile in ogni territorio

7. Apertura di ventilazione

Reset

AA 1.5V LR6 / R6

DC3.6V

5. Interrutttore C/F

TASTO

MODALITÀ

Standard

PREMERE

PER

TENERE

PREMUTO

PER

Accedere alla

impostazione

dell'ora e

della data

men

Visualizzare alternativ amente i

record dei valori di temper

atura/umidità corrente

massima e minima

Cancellare dalla memoria i record

relativi ai valori di massi-ma/minima

Modalità

impostazione

orologio/sveglia

Confermare

l'ora

Aumentare Diminuire

_______

Aumentare

rapida-mente

Diminuire

rapida-

mente

_______

light

mode

Modalità

sveglia

Accensione/

spegnimento

dell'

RCC

Avviare la

ricezione RCC

Passare dalla

visualizzazi

o- ne

dell'ora a

quella della

sveglia e viceversa

Passare dalla

visualizzazione

dell'ora a quella

della sveglia

e viceversa

Alternare i

canali

1-3 del sensore

per estemi

Avviare la

ricezione RCC

Avviare la

ricezione RCC

Attivare o

disattivare

la sveglia

_______

Cancellare dalla memoria

i record relativi ai valori di

massima/minima

Visualizzare alternativamente

i record deivalori di

temperatura/umidità

corren-te, massima e minima

PREMERE

PER

TENERE

PREMUTO

PER

PREMERE

PER

TENERE

PREMUTO

PER

Accendere la

retroilluminazione

per 8 secondi

Accendere la

retroilluminazione

per 8 secondi

Accedere alla

modalit

impostazione

della sveglia

Alternare i

canali 1-3

per estemi

_______

Attivare o

disattivare

la sveglia

Regolazione della

luminosità se

collegato

all'adattatore

Regolazione della

luminosità se

collegato

all'adattatore

DISPLAY LCD

1. Simboli delle previsioni meteoro-

logiche

2. Visualizzazione della temperatura interna

e Umidità interna

3. Visualizzazion della temperatura esterna

e Umidità esterna

5. Fasi lunari

6. Livello di comfort

[ ] Indicatore di temperatu-

ra/umidità massima/minima

[

] Indicatore di batteria scarica

[

] Indicatore del RF e canale esterno

[ ] Indicatore del segnale RCC

[ ] Sveglia(A1:1-5 giorni feriali,

Visualizzazione ora/sveglia

[

] Indicatore del fuso orario

[ ] Andamento della temperatura e

dell'umidità

[ ] Ora legale

[ ] Fuso orario(solo per gli Stati Uniti)

A2:6-7 weekend)

Page is loading ...

Explore Scientific WSC4009 Owner's manual

Brand: Explore Scientific

Model: WSC4009

Category: Alarm clocks

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

italiano: Explore Scientific WSC4009 Manuale del proprietario
français: Explore Scientific WSC4009 Le manuel du propriétaire
español: Explore Scientific WSC4009 El manual del propietario
Deutsch: Explore Scientific WSC4009 Bedienungsanleitung

Explore Scientific WSC4009 Owner's manual

This manual is also suitable for

Explore Scientific WSC4009 Owner's manual

in other languages

Related papers

Other documents