Panasonic DMP-B100P User manual

Brand: Panasonic

Model: DMP-B100P

Category: DVD players

Type: User manual

This manual is also suitable for

©Panasonic Corporation 2010.

Unauthorized copying and distribution is a violation

of law.

ORDER NO.CHM1002005CE

B35

Portable Blu-ray Disc Player

Model No. DMP-B100P

DMP-B100PC

Vol. 1

Colour

(S).......................Silver Type

TABLE OF CONTENTS

PAGE PAGE

1 Safety Precautions -----------------------------------------------3

1.1. General guidelines-----------------------------------------3

2Warning--------------------------------------------------------------4

2.1. Prevention of Electrostatic Discharge (ESD)

to Electrostatic Sensitive (ES) Devices---------------4

2.2. How to Recycle the Lithium Ion Battery (U.S.

Only)-----------------------------------------------------------4

2.3. How to Replace the Lithium Battery-------------------5

3 Service Navigation------------------------------------------------6

3.1. Introduction --------------------------------------------------6

3.2. General Description About Lead Free Solder

(PbF) ----------------------------------------------------------6

3.3. Important Notice 1:(Other than U.S.A.)---------------6

3.4. Static Electricity Protection Measures ----------------6

3.5. Ground for electrostatic breakdown

prevention----------------------------------------------------6

3.6. Handling of Traverse unit (optical pick-up) ----------7

4 Specifications ------------------------------------------------------8

4.1. Others (Licenses) ---------------------------------------- 10

5 Location of Controls and Components------------------ 11

6 Service Mode ----------------------------------------------------- 14

7 Troubleshooting Guide---------------------------------------- 20

7.1. Self-Diagnosis Functions------------------------------ 20

8 Service Fixture & Tools --------------------------------------- 22

9 Disassembly and Assembly Instructions--------------- 23

9.1. Disassembly Flow Chart-------------------------------- 23

9.2. P.C.B. location -------------------------------------------- 24

9.3. Main cabinet unit ----------------------------------------- 24

9.4. Traverse Unit ---------------------------------------------- 25

9.5. Main P.C.B. ------------------------------------------------25

9.6. Operation P.C.B. ----------------------------------------- 25

9.7. Disc cover ------------------------------------------------- 26

9.8. Monitor assembly---------------------------------------- 26

9.9. Monitor cover --------------------------------------------- 27

9.10. Mono arm-------------------------------------------------- 27

9.11. LCD panel ------------------------------------------------- 28

9.12. Cleaning of the Optical Pick-up ---------------------- 29

10 Measurements and Adjustments-------------------------- 30

10.1. Service Positions ---------------------------------------- 30

10.2. Caution for Replacing Parts--------------------------- 33

10.3. Adjustment Instruction when Exchange the

Traverse or Main P.C.B. (Servo Adjustment) ----- 34

11 Block Diagram--------------------------------------------------- 38

11.1. Overall Block Diagram---------------------------------- 38

12 Schematic Diagram -------------------------------------------- 39

12.1. Interconnection Schematic Diagram ---------------- 39

12.2. OPERATION Schematic Diagram------------------- 40

12.3. HP_REMOCON SCHEMATIC DIAGRAM--------- 41

12.4. LCD_SW SCHEMATIC DIAGRAM------------------ 41

12.5. BAT-CONNECTOR SHEMATIC DIAGRAM------- 41

12.6. SPEAKER SCHEMATIC DIAGRAM ---------------- 41

13 Printed Circuit Board------------------------------------------ 42

13.1. OPERATION P.C.B.------------------------------------- 42

13.2. HP_REMOCON P.C.B. -------------------------------- 44

13.3. BAT-CONNECTOR P.C.B. ---------------------------- 45

13.4. LCD_SW P.C.B. and SPEAKER P.C.B. ----------- 46

14 Appendix for Schematic Diagram------------------------- 47

14.1. Voltage and Waveform Chart ------------------------- 47

15 Exploded View and Replacement Parts List----------- 50

15.1. Exploded Views ------------------------------------------ 50

15.2. Electrical Replacement Parts List ------------------- 54

1 Safety Precautions

1.1. General guidelines

1. IMPORTANT SAFETY NOTICE

There are special components used in this equipment

which are important for safety. These parts are marked by

in the Schematic Diagrams, Circuit Board Layout,

Exploded Views and Replacement Parts List. It is essen-

tial that these critical parts should be replaced with manu-

facturer’s specified parts to prevent X-RADIATION,

shock, fire, or other hazards. Do not modify the original

design without permission of manufacturer.

2. An Isolation Transformer should always be used during

the servicing of AC Adaptor whose chassis is not isolated

from the AC power line. Use a transformer of adequate

power rating as this protects the technician from acci-

dents resulting in personal injury from electrical shocks. It

will also protect AC Adaptor from being damaged by acci-

dental shorting that may occur during servicing.

3. When servicing, observe the original lead dress. If a short

circuit is found, replace all parts which have been over-

heated or damaged by the short circuit.

4. After servicing, see to it that all the protective devices

such as insulation barriers, insulation papers shields are

properly installed.

5. After servicing, make the following leakage current

checks to prevent the customer from being exposed to

shock hazards.

1.1.1. Leakage current cold check

1. Unplug the AC cord and connect a jumper between the

two prongs on the plug.

2. Measure the resistance value, with an ohmmeter,

between the jumpered AC plug and each exposed metal-

lic cabinet part on the equipment such as screwheads,

connectors, control shafts, etc. When the exposed metal-

lic part has a return path to the chassis, the reading

should be between 1MΩ and 5.2MΩ.

When the exposed metal does not have a return path to

the chassis, the reading must be .

1.1.2. Leakage current hot check

(See Figure 1.)

1. Plug the AC cord directly into the AC outlet. Do not use

an isolation transformer for this check.

2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a

0.15μF capacitors, between each exposed metallic part

on the set and a good earth ground such as a water pipe,

as shown in Figure 1.

3. Use an AC voltmeter, with 1000 ohms/volt or more sensi-

tivity, to measure the potential across the resistor.

4. Check each exposed metallic part, and measure the volt-

age at each point.

5. Reverse the AC plug in the AC outlet and repeat each of

the above measurements.

6. The potential at any point should not exceed 0.75 volts

RMS. A leakage current tester (Simpson Model 229 or

equivalent) may be used to make the hot checks, leakage

current must not exceed 1/2 milliampere. In case a mea-

surement is outside of the limits specified, there is a pos-

sibility of a shock hazard, and the equipment should be

repaired and rechecked before it is returned to the cus-

tomer.

2Warning

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive

(ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-

trostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semi-

conductor "chip" components. The following techniques should be used to help reduce the incidence of component damage

caused by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-

num foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can

generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-

ble conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the

brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient

to damage an ES device).

2.2. How to Recycle the Lithium Ion Battery (U.S. Only)

2.3. How to Replace the Lithium Battery

This model is using a lithium battery for remote control ass’y.

NOTE:

This Lithium battery is a critical component.

(Type No.: CR2025 Manufactured by Energy Company, Panasonic Corporation.)

It must never be subjected to excessive heat or discharge.

It must therefore only be fitted in requirement designed specifically for its use.

Replacement batteries must be of same type and manufacture.

They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.

Do not attempt to re-charge the old battery or re-use it for any other purpose.

It should be disposed of in waste products destined for burial rather than incineration.

3 Service Navigation

3.1. Introduction

This service manual contains technical information, which allow service personnel's to understand and service this model.

Please place orders using the parts list and not the drawing reference numbers.

If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.

3.2. General Description About Lead Free Solder (PbF)

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this

equipment in considering the globally environmental conservation.

The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin

(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that

of the normal solder.

Definition of PCB Lead Free Solder being used

Service caution for repair work using Lead Free Solder (PbF)

• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.

(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)

• To put lead free solder, it should be well molten and mixed with the original lead free solder.

• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.

• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the

lead free solder.

• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees

C (662±86°F).

Recommended Lead Free Solder (Service Parts Route.)

• The following 3 types of lead free solder are available through the service parts route.

RFKZ03D01KS-----------(0.3mm 100g Reel)

RFKZ06D01KS-----------(0.6mm 100g Reel)

RFKZ10D01KS-----------(1.0mm 100g Reel)

Note

* Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

3.3. Important Notice 1:(Other than U.S.A.)

1. The service manual does not contain the following information, because of the impossibility of servicing at component level

without concerned equipment/facilites.

a. Schematic diagram, Block Diagram and PCB layout of MAIN PCB.

b. Parts list for individual parts for MAIN PCB.

2. The following category is/are recycle module part. please send it/them to Central Repair Center.

• TRV/MAIN PCB MODULE (B100PC:RFKNB100PC)

3. For USA market(B100P):

The Traverse and main P.C.B for PBD model is offered respectively for the market maintenaince.

For the information about pairing adjustment of the Traverse and main P.C.B.,please refer to "10.3. Adjustment Instruction

when Exchange the Traverse or Main P.C.B. (Servo Adjustment)" .

3.4. Static Electricity Protection Measures

• The laser diode in the traverse unit (optical pick-up) may break down due to potential difference caused by static electricity of

clothes or human body.

So, be careful of electrostatic breakdown during repair of the traverse unit (optical pick-up).

3.5. Ground for electrostatic breakdown prevention

• As for parts that use optical pick-up (laser diode), the optical pick-up is destroyed by the static electricity of the working environ-

ment.

Repair in the working environment that is grounded.

The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder.

(See right figure)

3.5.1. Work table grounding

• Put a conductive material (sheet) or steel sheet on the area where the traverse unit (optical pick-up) is placed, and ground the

sheet.

3.5.2. Human body grounding

• Use the anti-static wrist strap to discharge the static electricity from your body.

3.6. Handling of Traverse unit (optical pick-up)

1. Do not subject the traverse unit (optical pick-up) to hard shock as it is high precision mechanism.

2. Install the traverse unit, and then remove the short pin to discharge.

Connect the connector in a short time.

3. Take care not to apply excessive stress to the flexible cable.

4. Do not turn the variable resistor (laser power adjustment).

It has already been adjusted.

4 Specifications

Power supply: DC12V(DC IN terminal)

DC7.2V

(Exclusive battery terminal)

Power consumption:

Play Mode: Approx. 18W (Unit only

approx.15.5W) (B100P)

Approx. 19W (Unit only

approx.16W) (B100PC)

Recharge Mode:

(Quick Start [OFF]):

Approx. 18W

Recharge Mode:

(Quick Start [ON]):

Approx. 22W

Standby Mode:

(Quick Start [OFF]):

Approx. 0.5W

Standby Mode:

(Quick Start [ON]):

Approx. 5W

(using included AC adaptor)

AC Adaptor:

Power source: 110V-240V, 50/60Hz

Power consumption: 36W

DC output: 12V, 2000mA

Car DC Adaptor:

DC output: 12V, 2A

Vehicle with 12V battery only

Battery pack

DY-DB30(lithium ion):

Voltage: 7.2V

Capacity: 5800mAh(typ)

5400mAh(min)

39Wh

Dimensions

(excluding protrusions and

battery):

(WxDxH):

238mm x 188.3mm x 52.7mm

/8" x 7

/32" x 2

/16")

Mass:

Including battery: approximately 1392g [49.10oz]

Without battery: approximately 1157g [40.81oz]

Operating temperature range: +5°C to +35°C(+41 to +95°F)

Operating humidity range: 10% - 80%RH (no condensation)

LCD screen:

8.9" -Si, TFT wide-screen LCD

(1024 x 600 x RGB)

HDMI(B100PC)

AUDIO/VIDEO output:

number of terminals: 1 system

Speaker:

output: 0.5W + 0.5W (8Ω)

Head phone output:

output:

stereo mini-jack( 3.5mm)

number of terminals: 1 system

Battery duration(at 20°C)

Using headphones (B100P)

when brightness is set to

"-5" while playing DISC:

3.5 hours

when brightness is set to

"0" while playing DISC:

3.25 hours

when brightness is set to

"+5" while playing DISC:

3 hours

Battery duration(at 20°C)

Using headphones (B100PC)

Option Battery pack:

DY-DB300

when brightness is set to

"-5" while playing DISC:

3.5 hours/6 hours (DB300)

when brightness is set to

"0" while playing DISC:

3.25 hours/5.5 hours (DB300)

when brightness is set to

"+5" while playing DISC:

3 hours/5 hours (DB300)

Battery recharge time:

(at 20°C)(B100P)

5 hours

Battery recharge time:

(at 20°C)(B100PC)

5 hours/8 hours (DB300)

Pickup:

Wave Length: 405nm/660nm/780nm (BD/DVD/

CD)

Laser power: CLASS II/CLASS II/

CLASS I (BD/DVD/CD)

(B100P)

CLASS 1M/CLASS 1M/

CLASS 1M (BD/DVD/CD)

(B100PC)

Regional Code: DVD: #1

BD: Region A

Media:

Playable disc:

BD-Video: BD-ROM Version2

BD-RE: Version3 (SL:Single Layer/

DL:Dual Layer), JPEG

BD-R: Version2 (SL:Single Layer/

DL:Dual Layer)

DVD-RAM: DVD Video Recording format (*3),

AVCHD format, JPEG

DVD-R: DVD-Video format (*1), DVD

Video Recording format(*1), (*3)

AVCHD format(*1), JPEG(*2),

MP3(*2)

DVD-R DL: DVD-Video format (*1), DVD

Video Recording format(*1), (*3)

AVCHD format(*1), JPEG(*2),

MP3(*2)

DVD-RW: DVD-Video format (*1), DVD

Video Recording format(*1), (*3)

AVCHD format(*1)

+R: Video(*1), AVCHD format(*1)

+R DL: Video(*1), AVCHD format(*1)

+RW: Video(*1), AVCHD format(*1)

DVD-VIDEO DVD-Video format

CD-Audio CD-DA

CD-R/CD-RW CD-DA, JPEG(*2), MP3(*2)

*1: Finalizing is necessary.

*2: ISO9660 level1 or 2(except for extended formats), Joliet.

*3: CPRM is not supported.

This unit is compatible with multi-session.

This unit is not compatible with packet writing.

SD card:

SD Memory Card(*4)

formatted FAT12, FAT16,

FAT32(*5),exFAT(*6):

JPEG,AVCHD format,MPEG-2

*4: includes SDHC, SDXC card..

includes miniSD

Card(need a miniSD Adaptor.)

includes microSD/microSDHC/micro SDXC(B100PC) Card.

(need a microSD Adaptor.)

*5: Not support long file name.

*6: SDXC only.

Contents:

JPEG (*7):

SD card, CD-R/RW, DVD-RAM, BD-RE, DVD-R:

Pixcels: 34x34~8192x8192

Sub Sampling: 4:2:2, 4:2:0

Motion JPEG not supproted

SD card: JPEG conforming DCF(Design

rule for Camera File system)

Maximum numbers of folders and files:

*7: Motion JPEG not supported.

MP3:

CD-R, CD-RW, DVD-R:

Compression rate: 32kbps~320kbps

Sampling rate: 44.1kHz, 48kHz

AVCHD (H.264):

SD card, DVD: AVCHD format V1.0

HDMI (B100PC): 480p(525p) / 1080i(1125i) /

720p(750p) /1080p(1125p)HDMI

(x.v.Color

, High Bit rate Audio)

(This unit supports “HDAVI

Control 5” function.)

Solder: This model uses lead free

solder(PbF).

Note: Specifications are subject to

change without notice.

4.1. Others (Licenses)

5 Location of Controls and Components

B100P

B100PC

6 Service Mode

Information necessary for service can be displayed.

Service mode setting:

1. Turn the power off.

2. Press the [SUB MNU] + [PLAY] and [VOL DOWN] button simultaneously for five seconds.

3. It is displayed on LCD as [SERV]. : It is shown to have entered the service mode.

([PLEASE WAIT] is displayed previously according to the A/V mode.)

4. The command is transmitted by attached remote control.

Method of making clear service mode : Press the power button (power off).

The display of information to each command is as follows.

NOTE:

Do not use it excluding the designated command.

Item LCD display Key operation

Mode name Description (Remote controller key)

Release Items Item of Service Mode executing is cancelled. Press[0][0] or [Return] in service

mode.

Error Code Display Last Error Code of U/F held by memory is dis-

played on FL.

*Details are described in "Self-Diagnosis

Functions".

7.1. Self-Diagnosis Functions.

If any error history does not exist,

[F00] is displayed.

Press [0] [1] in service mode.

ROM Version Display The display contents are switched over every

5 seconds.

1. Region code

2. Main firm version

3. Timer firm version

4. Drive firm version

5. ROM correction version

6. BOO2 version

7. BOO3 version

Press [0] [2] in service mode.

Drive Check Simple quality of BD drive

*If the date of the present or the

trouble occurred time is incorrect, it

may be not able to judge correctly.

Press [0] [3] in service mode.

Drive Check Simple quality of BD drive

*If the date of the present or the

trouble occurred time is incorrect, it

may be not able to judge correctly.

Press [3] [8] in service mode.

Laser Used Time

Indication

Check laser used time (hours) of drive.

(****) is the used time display in

hour.

Laser used time of BD/ DVD/ CD

in Playback/Recording mode is

counted.

Press [4] [1] in service mode.

Item LCD display Key operation

Mode name Description (Remote controller key)

BD drive last error BD drive error code display. 1. Error Number is displayed for 5

seconds.

2. Time when the error has occurred

is display for 5 seconds.

YY: Year

MM: Month

DD: Day

3. Last drive error (1/2) is displayed

for 5 seconds.

00 : Bad disc

03 : Bad disc

04 : Bad disc or drive malfunction

4. Last drive error (2/2) is displayed

for 5 seconds.

5. Error occurring disc type is dis-

played for 5 seconds.

Press [4] [2] in service mode.

Item LCD display Key operation

Mode name Description (Remote controller key)

6. Disc maker ID is displayed for 5

seconds.

7. Factor of drive error (hexadeci-

mal) occurring is left displayed.

In case that the maker cannot be

identified, display is blackout.

Item LCD display Key operation

Mode name Description (Remote controller key)

8. When the last error doesn't exist .

CEC (H) output check Check of the CEC terminal high output of

HDMI.

Press [5] [5] in service mode.

CEC (L) output check Check of the CEC terminal low output of

HDMI.

Press [5] [6] in service mode.

Manufacturing Date Read out the manufacturing date of the unit.

YY: Year

MM: Month

DD: Day

Press[6][1]in service mode.

Delete the Laser Used

Time

Laser used time information stored in the

memory of the unit is deleted.

Press [9] [5] in service mode.

Delete the Last Drive

Error

Laser Drive Error information stored on the

BD Drive is deleted.

Press [9] [6] in service mode.

Delete the Error History Error History information stored on the unit is

deleted.

Press [9] [7] in service mode.

Initialization of Error code Last Error Code information stored by timer is

deleted. (Write in F00)

Press [9] [8] in service mode.

Initialization of the

Service Mode

Last Drive Error, Error History and Error code

information stored on the unit are initialized to

factory setting.

Press [9] [9] in service mode.

Item LCD display Key operation

Mode name Description (Remote controller key)

Release Service Mode Release Service Mode and turns the Power

Off.

Display in STOP (SS) mode. Press [POWER] button on the front

panel or Remote controller in ser-

vice mode.

Item LCD display Key operation

Mode name Description (Remote controller key)

7 Troubleshooting Guide

7.1. Self-Diagnosis Functions

Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has

occurred.

U**, H** and F** are stored in memory and held.

You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode.

In case of clear the self-diagnosis display, remove the battery pack and the AC adaptor from the main unit after the power of the

main unit is turned off.

Error Code Diagnosis contents Description LCD Display

U580 Battery supply current abnormality A problem has occurred with the battery pack. Consult

your dealer.

U581 Abnormal charge time on battery power The battery pack has been recharging but has failed to

recharge for some reason. Recharge again.

U582 Battery-powered temperature anomaly You are recharging in a location that is too hot or too cold.

Recharge at normal temperature [+5 to +35 °C (+41 to

+95 °F)].

U59 Abnormal inner temperature detected Display appears when drive temperature exceeds 70°C.

The power is turned off forcibly.

For 30 minutes after this, all key entries are disabled.

The event is saved in memory as well.

"U59" is displayed for 30 minutes.

U72 HDMI connection error

(communication error)

This error is displayed when there are any communication

problems with the unit and the equipments (TV, amplifier

etc.) connected to the unit by HDMI. (or when there is a

problem with the HDMI cable).

The display disappears only when the connection is

released. Neither the button operation nor the passage of

the fixed time disappear the display.

U73 HDMI connection error

(authentication error)

When authentication error occurs while the equipments

(TV, amplifier etc.) are connected by HDMI. (or when

there is a problem with the HDMI cable).

The display disappears only when the connection is

released. Neither the button operation nor the passage of

the fixed time disappear the display.

U76 Connection error This error is displayed when equipment such as TVs or

amplifiers connected to the unit with the HDMI cable do

not correspond to the copyright protection. (The BD/DVD

video where the copyright is protected cannot be played.)

U77 Illegal disc error This error is displayed when it becomes impossible to

reproduce because of copyright illegal information.

U88 Restoration is operation.

(When the disc is in the disc tray)

This error is displayed when there is a disc in the disc tray

or abnormality is confirmed during playback. It is shown

that the restoration to return the main unit operation

normally is operating. It becomes possible to use as soon

as not the breakdown but the U88 display disappears.

Display for 30 seconds.

H19 No working Fun Motor Preserves the Error record in case the Fun Motor doesn't

work at the time of Power-On.

No display

F00 No error information Initial setting for error code in memory

(Error code Initialization is possible with error code initial-

ization and main unit initialization.)

Not automatic display. Press [0][1]

in service mode. (Remote control-

ler key)

F58 Drive hardware error When drive unit error is detected, the event is saved in

memory.

Not automatic display. Press [0][1]

in service mode. (Remote control-

ler key)

F74 HDMI Device Key Communication

error

This error is displayed when the information error is

occurred at HDMI device key loading.

F75 HDMI Device Key Loading error This error is displayed when the key of loaded is illegal at

HDMI device key loading.

Page is loading ...

Panasonic DMP-B100P User manual

Brand: Panasonic

Model: DMP-B100P

Category: DVD players

Type: User manual

This manual is also suitable for

Download PDF

report

Panasonic DMP-B100P User manual

This manual is also suitable for

Panasonic DMP-B100P User manual

Related papers

Other documents