Nodor H 2070 BK HK User manual

Brand: Nodor

Model: H 2070 BK HK

Category: Hobs

Type: User manual

This manual is also suitable for

The Nodor H 2070 BK HK induction cooktop is a versatile and powerful cooking appliance that offers a range of features to make cooking easier and more efficient. With four cooking zones, including a free zone, you can cook multiple dishes simultaneously, while the precise temperature control allows you to achieve perfect results every time. The cooktop also boasts a sleek and stylish design, making it a great addition to any modern kitchen.

PRODUCT INSTALLATION & SAFETY INSTRUCTION

These instructions are for your safety. Please read the following instructions carefully before proceeding with the installation

and use of this appliance. Keep the instruction manuals for future reference.

Warning: All installation work must be carried out by a suitably qualified person, strictly following

local building regulations and these instructions.

To avoid the risks that are always present when you use an electrical appliance it is important that this hob is installed

correctly and that you read the safety instructions carefully to avoid misuse and harzards.

Check the package and make sure you have all of the parts lsted and decide upon the appropriate location for your product.

If this product contains glass pleae take care with fitting or handling to prevent personal injury or damage to the product.

The specification plate shown on this appliance displays all the necessary identification information for ordering replacement

parts. If you sell the appliance, give it away, or leave it behind when you move house, please ensure that you pass on this

manual so that the new owner can become familiar with the appliance and its safety warnings.

SAFETY

All installation work must be carried out by a suitably qualified person, strictly following local building

regulations and these instructions.

 During Installation do not allow the supply cord to touch the hot parts of the appliance.

 Make sure that the supply cord is not caught under the appliance and avoid damage to the supply

cord. Alternations to the domestic wiring system must only be made by a qualified electrician.

 Please dispose of the packing material carefully.

 Warning: This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the appliance.

 Cleaning and user maintenance shall not be made by children without supervision. Keep the

appliance and its supply cord out of the reach of children less than 8 years old.

 If the supply cord becomes damaged, it must be replaced by the manufacturer, its service agent or

similarly qualified persons in order to avoid a danger or injury.

 The appliance is not intended to be operated by means of an external timer of separated remote

control system.

 The appliance is for domestic use only and only for cooking food. Do not use this appliance as a

source of heat.

 The manufacturer declines all liability for personal or material damage as a result of misuse or

incorrect installation of this appliance.

 Danger of burns! During use the appliance becomes hot.

 The appliance must be installed in accordance with installation instructions and all dimensions

must be followed.

 Before connecting the appliance to the power supply, check that the power supply voltage and

current rating correspondings with the power supply details shown on the appliance rating label.

 Never use a damaged appliance! Disconnect the appliance from the electrical outlet and contact

your retailer if it is damaged.

 Danger of electric shock! Do not attempt to repair the appliance yourself. In case of malfunction,

repairs are to be conducted by qualified personnel only.

 To avoid damaging the cord, do not squeeze, bend or chafe it on sharp edges. Keep it away from

hot surfaces and open flames.

 Lay out the cord in such a way that no unintentional pulling or tripping over it is possible. Keep the

appliance and its cord out of reach of children. Always turn the appliance off before disconnecting

it from the power supply.

 Disconnect the appliance from the power supply when not in use and before cleaning.

PRODUCT INSTALLATION & SAFETY INSTRUCTION

 Warning: This appliance is supplied with a three core supply cord and must be connected direct to

the mains electricity supply via a omni-polar or double pole switch having a 3mm minimum contact

gap on each connector. This appliance should be connected to a circuit which incorporates an

isolating switch providing full disconnection from the power supply.

 The fused spur should be installed in an easily reachable place so that in case of emergency the

appliance can be disconnected from power immediately.

 The fixed wiring must be protected against heat surfaces.

 Warning: The appliance and its accessible parts become hot during use. Care should be taken to

avoid touching heating elements.

 Warning: Ensure the cookware handle not overhang other cooking zone(s) that are ON. The

handle may be hot and keep away be touched by children.

 Children less than 8 years of age shall be kept away unless continuously supervised.

 No combustible material or products should be placed on this appliance at any time.

 Do not cook on a broken or cracked cooktop. If the cooktop surface been break or crack, switch

the appliance off immediately at the mains power supply (wall switch) and contact a qualified

technician.

 This appliance complies with electromagnetic safety standards.

 However, persons with cardiac pacemakers or other electrical implants (such as insulin pumps)

must consult with their doctor or implant manufacturer before using this appliance to make sure

that their implants will not be affected by the electromagnetic field.

 Do not let your body, clothing or any item other than suitable cookware contact the Induction glass

until the surface is cool.

 Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface

since they can get hot.

 Never leave the hob unattended when in use. Boilover causes smoking and greasy spillovers that

may ignite.

 Never use the hob as a worktop or for storage and Never leave any objects or utensils on the hob.

 Do not place or leave any magnetisable objects or electronic devices near the hob, as they may be

affected by its electromagnetic field.

 Never use the hob for warming or heating the room.

 After use, always turn of the cooking zones and the hob as described in this manual (i.e by using

the touch or touch slider controls). Do not rely on the pan detection feature to turn off the cooking

zone when removing the pans.

 Do not leave children alone or unattended in the area where the hob is in use.

 Do not repair or replace any part of the appliance unless specifically recommended in the manual.

All other servicing should be done by a qualified technician.

 Do not use a steam cleaner to clean the hob, and do not use scourers or any other harsh abrasive

cleaning agents to clean the hob, as these can scratch the glass.

 Do not use pans with jagged edges or drag pans across the glass surface as this can scratch the

glass.

 The hob is intended to be used in household and similar applications such as :

- Staff kitchen areas in shops, offices and other working environments;

- Farm houses;

- By clients in hotels, motels and other residential type enviornments;

- Bed and Breakfast type environments.

 Warning: Unattended cooking on the hob with fat or oil can be dangerous and may result in fire.

NEVER try to extinguish a fire with water, but switch off the hob and then cover flame. e.g. with a

lid or a fire blanket.

 Warning: Danger of fire, do not store items on the glass. If the glass is cracked, switch off the hob

to avoid the possibility of electric shock.

PRODUCT INSTALLATION & SAFETY INSTRUCTION

INSTALLATION

Due to himidity issue may damage the hob electronics, the hob is not recommended be installed

directly above a dishwasher, fridge, freezer, washing machine or clothes dryer. The wall, countertop

and any area closed by the cooking zone shall withstand heat. To avoid any damage, the sandwich

layer of the countertop and adhesive must be resistance to heat.

CONNECTING THE HOB TO THE MAINS POWER SUPPLY

This hob must be connected to the mains power supply only by a suitably qualified electrician. Before

connecting the hob to the mains power supply, check that:

1. The domestic wiring system is suitable for the power drawn by the hob.

2. The voltage corresponds to the value given in the rating plate

3. The power supply cable sections can withstand the load specified on the rating plate.

To connect the hob to the mains power supply, do not use adapters, reducers, or branching devices, as

they can overheating and fire. The power supply cable must not touch any hot parts and must be

positioned so that its temperature will not exceed 75˚C at any point.

Check with an electrician whether the domestic wiring system is suitable without alterations.

Any alterations must only be made by a qualified electrician.

 The cable must not be bent or compressed and be checked regularly. If the cable is damaged or

to be replaced, the operation must be carried out by qualified electrician with dedicated tools to

avoid any accidents.

 If the appliance is being connected directly to the mains an omnipolar circuit-breaker must be

installed with a minimum opening of 3mm between contacts.

PRODUCT INSTALLATION & SAFETY INSTRUCTION

 The installer must ensure that the correct electrical connection has been made and that it is

compliant with safety regulations.

 Disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

Note: For I 3060 BK HK / H 3060 BK HK / I 4060 BK HK model, this appliance requires a 32 Amp

Miniature Circuit Breaker.

TECHNICAL SPECIFICATION

Model

I 2030 BK HK

I 2070 BK HK

H 2070 BK HK

I 3060 BK HK

H 3060 BK HK

I 4060 BK HK

Cooking Zone

Supply Voltage

220V / 50HZ

Front (Left)

1500W

2300W

2800W

Rear (Left)

2300W

1500W

2000W

Front (Right)

2300W

3000W

2100W

2800W

Rear (Right)

2000W

Max. Rating Power

3500W

4600W

6800W

5800W

7200W

Free Zone (Left)

3500W

3600W

Free Zone (Right)

3600W

PRODUCT AND BUILT-IN DIMENSION

THIS MANUAL IS SUITABLE FOR USE ON BELOW MODELS:

INDUCTION HOB

Model : I 2030 BK HK

MIXED HOB

Model : H 2070 BK HK

INDUCTION HOB

Model : I 2070 BK HK

MIXED HOB

Model : H 3060 BK HK

INDUCTION HOB

Model : I 3060 BK HK

INDUCTION FREE ZONE HOB

Model : I 4060 BK HK

PRODUCT AND BUILT-IN DIMENSION

SELECTION OF INSTALLATION EQUIPMENT

Cut out the worktop surface according to the sizes shown in the drawing. For the purpose of

installation and use, a minimum of 5cm space shall be preserved around the hole. Be sure the

thickness of the worktop surface is at least 30mm. Please select heat-resistant worktop surface

material to avoid larger deformation caused by the heat radiation from the cooking surface. As shown

below:

Model

L(mm)

W(mm)

H(mm)

D(mm)

A(mm)

B(mm)

X(mm)

I 2030 BK HK

290

520

265

495

≥50

I 2070 BK HK

710

400

685

375

≥50

H 2070 BK HK

710

400

685

375

≥50

I 3060 BK HK

590

520

565

495

≥50

H 3060 BK HK

590

520

565

495

≥50

I 4060 BK HK

590

520

565

495

≥50

FASTENING THE HOB TO THE WORKTOP

1. Turn the hob upside down and place it on a soft surface.

2. Spread the seal around the edges of the ceramic glass with the adhesive side facing down. Make

sure the whole perimeter is sealed. Cut off any excessive material.

3. Mount the supplied clamps and screws on the hob, as shown (without tightening the screws).

4. Place the hob into the cutout of the worktop and then tighten the screws to clamp the cooktop

securely to the worktop.

5. Using a sharp cutter of trimmer knife, trim the excess sealing material around the edge of the hob.

Take care no to damage the worktop.

Under any circumstances, make sure the hob is well ventilated and the air inlet and outlet are not

blocked. Ensure the hob is in good work state. As shown below:

 The safety distance between the hob surface and the cupboard should be at least 760mm.

 Good ventilation is required around the appliance for easier dissipation of heat and lower power

consumption.

 Sufficient clearance is required around the appliance and should not be placed near anything that

may echo.

PRODUCT AND BUILT-IN DIMENSION

Model

A(mm)

B(mm)

C(mm)

E(mm)

I 2030 BK HK

760

≥50

≥20

Air intake

Air exit (≥5)

I 2070 BK HK

760

≥50

≥20

Air intake

Air exit (≥5)

H 2070 BK HK

760

≥50

≥20

Air intake

Air exit (≥5)

I 3060 BK HK

760

≥50

≥20

Air intake

Air exit (≥5)

H 3060 BK HK

760

≥50

≥20

Air intake

Air exit (≥5)

I 4060 BK HK

760

≥50

≥20

Air intake

Air exit (≥5)

ASSEMBLY

BEFORE INSTALL THE HOB, MAKE SURE THAT

 The worktop is square and level, and no structural members interfere with space requirements.

 The wall and the induced heating zone, near or above the worktop should be made of heat-

resistant material.

 If the hob is installed above an oven, the oven should have a built-in cooling fan.

 The installation will comply with all clearance requirements, applicable standards and regulations.

 A suitable isolating switch providing full disconnection from the mains power supply is incorporated

in the permanent wiring, mounted and positioned to comply with the local wiring rules and

regulations. The isolating switch must be of an approved type and provide a 3 mm air gap contact

separation in all poles (or in all active [phase] conductors if the local wiring rules allow for this

variation of the requirements)

 The isolating switch will be easily accessible to the customer with the hob installed.

 Disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

 Consult local building authorities and by-laws if in doubt regarding installation.

 Use heat-resistant and easy-to-clean finishes (such as ceramic tiles) for the wall surfaces

surrounding the hob.

LOCATING THE FIXING BRACKETS

 The unit should be placed on a stable, smooth surface (use the packaging).

 Do not apply force onto the controls protruding from the hob.

 The unit should be placed on a stable, smooth surface (use the packaging).

 Do not apply force onto the controls protruding from the hob.

AFTER INSTALL THE HOB, MAKE SURE THAT

 The power supply cable is not accessible through cupboard doors or drawers.

 There is adequate flow of fresh air from outside the cabinetry to the base of the hob.

 When installation above a drawer or cupboard space, a thermal protection barrier should be

installed below the base of the hob to avoid contacting the bottom of the hob.

ASSEMBLY

USE

USING THE TOUCH / TOUCH SLIDER CONTROLS

 The controls respond to touch, no need to apply any pressure.

 Use the ball of the finger, not its tip.

 A “beep” sound will be responded each time when a touch is registered.

 Make sure the controls are always clean, dry, and that there is no object (e.g. a utensil or a cloth)

covering them. Even a thin film of water may make the controls difficult to operate.

USER INTERFACE

Keys Reference and Description

ON/OFF

CHILD LOCK

TIMER

PAUSE

DOUBLE

RING

COOKING

FUNCTIONS

COOKING ZONE SELECT

FREE ZONE

POWER REGULATING / TIMER (SLIDING UP / DOWN)

BOOST

POWER REGULATING

(DOWN / UP)

TIMER CONTROL

(DECREASE / INCREASE)

TIMER CONTROL

(DECREASE / INCREASE)

USE

Indicators Reference and Description

POWER LEVEL / TIMER SETTING

MELTING /

DEFROSTING

About 50C

HEATING /

WARMING

About 70C

SIMMERING /

~ BOILING

Slow Cooking

TIMER

FREE ZONE

CONNECT

USING THE COOKING HOB

To start cooking

 Touch the ON/OFF key for 3 seconds. After power on, the buzzer beeps once, all

displays show “ – “ or “0”, indicating that the cooking hob has entered the state of

standby mode.

 Place a suitable pan on the cooking zone. Make sure the bottom of the pan and

the surface of the cooking zone is clean and dry. According to the cooking zone

where the pan is placed, touch the COOKING ZONE SELECT key if there is, and

the POWER LEVEL indicator will shown “0” when selected and will be flashing.

 Adjust power level setting by touching the POWER REGULATING slider control

or touch the POWER REGULATING key “+” or “-“. The power level will start at 0,

touching the slider or ”+” will count up the power level from 0 to 9 (max. power) in

numerical order. Or touching the slider or “-“ will reduce the power level to 0 and

the cooking zone will be turned off.

If a power level setting is not chosen within 20 seconds, the cooking hob will automatically switch

off. And have to restart again from step 1.

The power level setting can be adjusted at any time during cooking.

When the indicator flashes alternately with the power level setting

Ensure:

 Place a pan on the correct induction cooking zone or,

 Place a suitable pan (please read the section of Choosing the right Cookware) on the induction

cooking zone or,

 The pan is properly centre on and large enough to cover the induction cooking zone.

No heating takes place unless there is a suitable pan on the induction cooking zone.

The indicator will automatically turn off after 1 minutes if no suitable pan is placed on the induction

cooking zone.

When finish cooking

 Touch the ON/OFF key, the power level of the hob or the corresponding cooking zone will be OFF

straight away.

 Touch the COOKING ZONE SELECT key if there is, touch the POWER REGULATING slider

control to decrease the power to “0” level.

 Always beware of hot surfaces. “H” will be indicated and shown out which cooking zone is

remaining hot. ”H” indication will be OFF when the hot surfaces cooled down to a safety

USE

temperature. This can also be used as an energy saving function if using the residual hot cooking

zone to heat or warm a pan.

Using the Boost function

To activate the Boost function, touch the COOKING ZONE SELECT key if there is, touch the relevant

cooking zone BOOST key, the POWER LEVEL indicator show “P.” or “boot.” and the power reach Max.

To cancel the Boost function, touch the COOKING ZONE SELECT key if there is, touch the POWER

REGULATING slider to cancel the Boost function and the cooking zone will revert to the power level.

 The function can work in any cooking zone.

 The cooking zone returns to level 9 after 5 minutes automatically.

Using Cooking Functions

(Only available on I 3060 BK HK / H 3060 BK HK model)

There are 3 handy cooking functions, touch the COOKING FUNCTIONS key each time to move from

one function to the other.

- Melting or defrosting (about 50C)

- Heating or keeping warm (about 70C)

- Simmering, temperature close to boiling, useful for slow cooking

Using Child Lock Function

 Lock the controls to prevent unintended use (for example children accidentally turning the cooking

zones on).

 When the controls are locked, all the controls except the ON/OFF key are disabled.

To lock the controls, touch the CHILD LOCK key for 3 seconds. The indicator if any above the CHILD

LOCK key will be ON, the TIMER SETTING indicator will show “Lo“ or “Loc.” and a beep sound will be

responded.

To unlock the controls, touch and hold the CHILD LOCK key control for a while.

When the hob is in the lock mode, all the controls are disable except the ON/OFF key, turn the hob

OFF with the ON/OFF key control in an emergency, but shall unlock the hob first before next operation.

Using the Timer

There are two different ways to use the timer:

 Using the timer as a minute minder (Alarm). In this case, the timer will not turn any cooking zone

off when the set time is up.

 Using the timer to turn one cooking zone off after the set time is up, and the timer can be set for up

to 99 minutes.

Using the Timer as a Minute Minder (Alarm)

(Not available for I 3060 BK HK / H 3060 BK HK model)

 No cooking zone is selected.

 Touch the TIMER key. The TIMER SETTING indicator will start flashing “10”, and the minute

minder can be set.

 Using the TIMER CONTROL key, the “+” or “-“ controls can set the timing from 1 to 99 minutes.

Hint:

USE

Touch the “-“ or “+” control of the TIMER CONTROL key once to decrease or increase by 1 minute.

Touch and hold the “-“ or “+’ control of the TIMER CONTROL key to decrease of increase by 10

minutes.

Touch the “-“ and “+” together, the timer is cancelled and the TIMER SETTING indicator will turn

OFF.

 When the time is set, it will begin to count down immediately. The TIMER SETTING indicator will

show the remaining time.

 The buzzer will beep for 30 seconds and the TIMER SETTING indicator will turn OFF when the

setting time is finished.

Note : Minute Minder will only work at normal mode

Using the Timer as a Minute Minder (Alarm)

(Only available for I 3060 BK HK / H 3060 BK HK model)

 Select any cooking zone by touching the POWER REGULATING slider control for any

power level, the dot next to the POWER LEVEL indicator will flash for 5 seconds.

 Once the dot stops flashing, using the TIMER CONTROL key, “+” or “-“ controls to set the timing

from 1 to 99 minutes.

Hint:

Touch “-“ or ”+” control of the TIMER CONTROL key once to decrease or increase by 1 minute.

Touch and hold “-“or ”+” control of the TIMER CONTROL key to decrease or increase by 10

minutes.

 When the time is set, it will begin to count down immediately. The TIMER SETTING

indicator will show the remaining time, and the dot next to the TIMER SETTING indicator

will keep on flashing.

 The buzzer will beep and the TIMER SETTING indicator will turn off when the setting time is

finished.

Setting the Timer to switch off cooking zones

(Not available for I 3060 BK HK / H 3060 BK HK model)

 Select the relevant cooking zone by touching the COOKING ZONE SELECT key.

 Touch the TIMER key, the TIMER SETTING indicator with start flashing “10” and the timer can be

set.

 Using the TIMER CONTROL key, “+” or “-“ controls can set the timing from 1 to 99 minutes.

Hint:

Touch “-“ or “+” control of the TIMER CONTROL key once to decrease or increase by 1 minute.

Touch and hold “-“ or “+’ control of the TIMER CONTROL key to decrease of increase by 10 minutes.

Touch “-“ and “+” control of the TIMER CONTROL key together, the timer is cancelled and the TIMER

SETTING indicator will turn OFF.

 When the time is set, it will begin to count down immediately. The TIMER SETTING indicator will

show the remaining time and flash for 5 seconds.

Note: The red dot next to the POWER LEVEL indicator will be ON indicating that cooking zone is

selected.

 When the setting time is finished, the corresponding cooking zone will be switch off automatically.

Other cooking zone will keep operating if they are turned on previously.

Setting the Timer to switch off cooking zones

(Only available for I 3060 BK HK / H 3060 BK HK model)

 Selecting the relevant cooking zone by touching the POWER REGULATING slider to set the

power level, the dot next to POWER LEVEL indicator will flash for 5 seconds.

 Before the dot stops flashing, using the TIMER CONTROL key, “+” or “-“ control can set the timing

from 1 to 99 minutes.

USE

Hint:

Touch “-“ or “+” control of the TIMER CONTROL key once will decrease or increase by 1 minute.

Touch and hold “-“ or “+”control of the TIMER CONTROL key will decrease or increase by 10

minutes.

 When the time is set, it will begin to count down immediately. The TIMER SETTING indicator will

show the remaining time and the TIMER SETTING or TIMER indicator will flash for 5 seconds.

 After that, if the TIMER SETTING or TIMER indicator will keep on flashing means that the TIMER

SETTING indicator shows the relevant cooking zone remaining time until the timer expires; or else

the TIMER SETTING or TIMER indicator will keep ON until the timer expires.

 When the setting time is finished, the corresponding cooking zone will be switch off automatically.

Other cooking zone will keep operating if they are turned on previously.

 When using “the Timer as a Minute Minder (Alarm)” and “the Timer to switch off the cooking zones”

together, the TIMER SETTING indicator will show the remaining time of Minute Minder (Alarm) as

first priority. Touch the POWER REGULATING slider of relevant cooking zone to show the

remaining time of switch off timer.

Setting the Timer on more than one cooking zones

 When the TIMER is setting for several cooking zones simultaneously, the dot next to the POWER

LEVEL indicator of the relevant cooking zones are ON. The TIMER SETTING indicator will show

out the minimum setting time of the relevant cooking zones and the dot next to the POWER

LEVEL indicator of the corresponding relevant cooking zone will flash.

 Once the setting time is finished, the POWER LEVEL indicator of the corresponding cooking zone

will be switch off.

Note: Touch the COOKING ZONE SELECT key will show out the setting TIMER on the TIMER

SETTING indicator.

Using the Pause function

(Only available for I 3060 BK HK / H 3060 BK HK model)

The hob has a handy restart function to pause and restart the cooking process if interrupted.

 When the hob is ON and working, touch the PAUSE key, all cooking zone will stop working, and

all LED indicators will show the symbol “=”.

 Touch the PAUSE key again, all settings will be restarted at the previous setting.

Using the Double Ring Zone function

(Only available for H 3060 BK HK model)

 The right cooking zone can be operated as single or double ring power operation.

 Touch the DOUBLE RING key to select single or double ring power operation.

 When the red dot indicator on top of the DOUBLE RING key is ON, the right cooking zone is at

double ring (Full Power) operation, or else if the indicator is OFF, the cooking zone is at single ring

(Normal Power) operation.

Free Zone area

(Only available for H 3060 BK HK / I 4060 BK HK model)

 This area can be used as a single cooking zone, accordingly to the cooking needs anytime.

 Free Zone area is made of two independent inductors that can be controlled separately. When

working as a single cooking zone, a cookware is moved from one zone to the other one within the

Free Zone area keeping the same power level of the zone where the cookware originally was

placed, and the part that is not covered by cookware is automatically switched off.

 IMPORTANT. Make sure to place the cookware be centre on the single cooking zone. The ideal

receipe is an oval or rectangular saucepan, or a saucepan. Example, BBQ Grill Plate or

SteamChef.

USE

Examples of good pan placement and bad pan placement.

Good placement

Bad placement

 To activate the Free Zone area as a single cooking zone, simply touch the FREE ZONE key, or

touch the corresponding paired COOKING ZONE SELECT keys simultaneously.

 The FREE ZONE CONNECT indicator next to the POWER LEVEL indicator will be light up.

 The FREE ZONE CONNECT indicator will be shown “n” or “u” according to the pan placement on

which cooking zone.

 Selecting the relevant cooking zone by touching the POWER REGULATING slider to set the

power level.

 If the pan is moved from the front to rear cooking zone (or viceversa), the Free Zone area detects

automatically the new position and keeping the same power.

SPECIAL FUNCTIONS

Over-Temperature Protection

A temperature sensor equipped can monitor the temperature inside the hob. When an excessive

temperature is monitored, the hob will stop operation automatically.

Detection of Small Articles

When an unsuitable size or non-magnetic pan (e.g. aluminum), or some other small item (e.g. knife,

fork, key) has been left on induction cooking zone, the hob automatically go on to standby in 1 minute.

The fan will keep cooking down the induction hob for a further 1 minute.

Residual Heat Indicator

When the hob has been operating for some certain time, there will be some residual heat. The letter “H”

will be appeared to warn that it is still too hot to touch any area of the hob surface.

Auto Shutdown Protection

Auto shutdown is a safety protection function for the hob. It shuts down automatically if ever forget to

turn off after cooking. The default working times for various power levels are shown in the below table:

When the pot is removed, induction cooking zone can stop heating immediately and the hob

automatically switch off after 2 minute.

People with a heart pace maker should consult with their doctor before using this unit.

Power level

1~3

4~6

7~8

Default working timer (min)

360

180

120

USE

Protection against unintended cooking

For ceramic hob, If the electronic control detects a button being held down for approx. 10 seconds, the

hob will be switched off automatically. The control sends out an audible error signal to warn the

sensors have detected the presence of an object. The display will indicate an error code “ER03” or

“ER06" if the hob is still hot. The residual display “H” or “ER03” or “ER06" flash alternatively.

USE

A WORD ON CERAMIC COOKING

Ceramic cooking is catering for all kinds of cookware, with its radiant heat cooking zones and its

electronic touch controls, multi-functions, making it be the ideal choice for the modern family. The use

of ceramic cooking is extremely user-friendly, durable and safe.

A WORD ON INDUCTION COOKING

Induction cooking is a safe, advanced, efficient, and economical cooking technology. It works by

electromagnetic vibrations generating heat directly in the pan, rather than indirectly through heating the

glass surface. The glass becomes hot only because the pan eventually warms it up.

Choosing the right Cookware

 Only use cookware with a base suitable for induction cooking. Look for the induction symbol on the

packaging or on the bottom of the pan.

 Check whether the cookware is suitable by carrying out a magnet test. Move a magnet towards

the base of the pan. If it is attracted, the pan is suitable for induction.

 If there is no available magnet:

1. Put some water in the pan for checking.

2. If does not flash in the display and the water is heating, the pan is suitable.

 Cookware made from the following materials is not suitable: pure stainless

steel, aluminum or copper without a magnetic base, glass, wood, porcelain, ceramic, and

earthenware.

Do not use cookware with jagged edges or a curved base.

Make sure that the base of the pan is smooth, no jagged edges or a curved base, sits flat against the

glass, and is the same size as the cooking zone. Use pans whose diameter is as large as the graphic of

the zone selected. Using a pot a slightly wider energy will be used at its maximum efficiency. If using

smaller pot, efficiency could be less than expected. Pot less than 140 mm could be undetected by the

hob. Always centre the pan on the cooking zone.

Always lift pans off the Induction hob – do not slide, or they may scratch the glass.

Iron Pot

Magnetic Circuit

Ceramic Glass Plate

Induction Coil

Induced Currents

CARE & MAINTENANCE

Appliance Cleanliness

 Avoid rubbing with any abrasive or with the base of the pans, etc. as this will wear the markings on

the top of the hob.

 Clean the surface on a regular basis to prevent the build up of food residue.

 The surface may be easily be cleaned in the following way:

Type of dirt

Cleaning method

Cleaning materials

Lime scale

Apply white vinegar to the surface, then wipe it dry with

soft cloth

Special ceramic cleaner

Burnt-on stains

Clean with damp cloth and dry it with a soft cloth

Special ceramic cleaner

Light stains

Clean with damp cloth and dry it with a soft cloth

Cleaning sponge

Melted plastics

Use a scraper suitable for ceramic glass to remove

residue

Special ceramic cleaner

Page is loading ...

Nodor H 2070 BK HK User manual

Brand: Nodor

Model: H 2070 BK HK

Category: Hobs

Type: User manual

This manual is also suitable for

Download PDF

report

Nodor H 2070 BK HK User manual

This manual is also suitable for

Nodor H 2070 BK HK User manual

Other documents