FIORENTINI BIG 48 Instructions For Use And Maintenance Manual

Brand: FIORENTINI

Model: BIG 48

Category: Scrubber

Type: Instructions For Use And Maintenance Manual

This manual is also suitable for

BIG 38

FIORENTINI BIG 48 is a floor scrubber-dryer designed for industrial cleaning. It is equipped with a 38/48-liter solution tank and a 45-liter recovery tank. The BIG 48 has a working width of 48 centimeters and a theoretical cleaning performance of 1,150 square meters per hour. The machine is powered by two 12-volt batteries and has a runtime of up to 3 hours. The BIG 48 is equipped with a variety of features to make cleaning easier and more efficient, including:

Variable speed control allows the operator to adjust the speed of the machine to suit the cleaning task.
Self-propelled drive makes it easy to maneuver the machine around obstacles.

Variable speed control allows the operator to adjust the speed of the machine to suit the cleaning task.
Self-propelled drive makes it easy to maneuver the machine around obstacles.

ING. O. FIORENTINI S.p.A.

INDUSTRIAL CLEANING MACHINES

FLOOR SCRUBBER-DRYER

MODEL BIG 38/48

INSTRUCTIONS FOR USE

AND MAINTENANCE

CONTENTS

GENERAL INFORMATION

1.1. Symbols used……………………………….…….........................……..................page

1.2. Disclaimer…...............................................................................................................

1.3. Use of the manual…………......…………………………....….........…….............…….

1.4. Warranty..............................................................…………...…………...….…...........

1.5. Declaration of Conformity........................................…...........………….………..……

MACHINE FEATURES AND TECHNICAL DATA

2.1. Identification………………......…...............................….…………….….……............

2.2. Description and components….……………...…....................................................…

2.3. Technical data sheet................................…........……………………….....…............

SAFETY

3.1. Intended use.…………..………....……………....…....……………….....………….......

3.2. Improper use…………………………………………………………………..…………...

3.3. Recommended equipment……………………………………………………….....……

3.4. Operator qualifications..............……………….......……………...…………................

3.5. Safety and warning devices……………..................…...………….............................

3.6. Residual risks………………………………………………………………………………

3.7. Safety signs……………………………………………………………….................…...

STAR-TUP AND OPERATION INSTRUCTIONS

4.1. Transport and handling............. .….....................…....………….….…………........

4.2. Storage........................... ...............…………….………….....................................

4.3. Unpacking the machine... .....................……………………..........................….....

4.4. Handling the unpacked machine…. .…..........………………………..……............

4.5. Installation…..........................................................………………..……................

4.5.1. Battery installation……..........……..….......……………….…...….…….........….....

4.6. Control and monitoring devices……………………………….............................…

4.6.1. Dashboard…………………………………………………………………….......……

4.7. Operation…………………………………………..........................................……..

4.7.1. Starting and preparing the machine………………………………..……………….

4.7.2. Choice of detergent………………………………………………………….………..

4.7.3. Adjustment of the driving position….………………………………............………

Congratulations on your choice!

Thank you for choosing to purchase a product by FIORENTINI S.p.A., a global leader in

the manufacture and marketing of industrial cleaning machines.

Our long-standing experience and acquired know-how are the best guarantee of the

technical quality of your purchase; all our products are built from top quality materials to

ensure maximum reliability, sturdiness and functionality and to meet the requirements of

even the most demanding customers. FIORENTINI has recently obtained UNI EN ISO

9001:2000 certification for its quality system certificate.

Feel free to contact us with any technical or commercial inquiry; we will be happy to

supply any details and information that you may need.

4.7.4. Pedal functions…………………………………………………………..........……..

4.7.5. Regulating the detergent solution………………………………………….….……

4.7.6. Squeegee adjustment…..……………………………….………………….….……

4.7.7. Drain hoses………………….............…......………….………..................….……

4.7.8. Replacing the brushes………………………………..…………………….....….…

4.7.9. Replacing the squeegee blade………………….…………………………....…….

4.7.10 Tilting the fairing…………………………..............…………………………

MAINTENANCE

5.1. Routine maintenance table…… ……..................….....…..………….................

5.2. Battery maintenance……………………..……………………………………..…..

5.2.1. Measuring specific gravity……………………….……………..................….

5.2.2. Topping up the water…………………………...............................................….

5.2.3. Charging limits……………………………………………………………………….

5.2.4. Batteries not in continuous service or inactive …..........………..............……...

5.2.5. Battery disposal….......………………………………………..…………………….

5.3. Maintenance of the suction motor…..……………………....……………………..

5.4. Checking the electrical system………………………………….……….………….

5.5. Inspection summary schedule……………………………….................………….

5.6. Maintenance Log………………………...............………………………………….

TECHNICAL SUPPORT

6.1. Contact details for technical support............…………................……..................

6.2. Complaint report……………………………..…………...…………………..............

MACHINE FEATURES AND TECHNICAL DATA

BIG 38/48

1. GENERAL INFORMATION

1.1. SYMBOLS USED

This symbol is used to call the operator’s attention to important procedures or precautions

required to prevent harm to users or the machine

This symbol is used to call the operator's attention to important general information.

1.2. DISCLAIMER

1.3. USE OF THE MANUAL

This manual provides extensive coverage of all topics deemed necessary for easy and safe use of the

machine, in compliance with European Directives on product safety.

We therefore advise all authorised operators to read all parts of the manual carefully, to follow its indications

thoroughly and to contact FIORENTINI S.p.A. for clarifications in case of any doubt. The manual should also

be used for reference whenever there are doubts concerning a procedure or operation and for training new

operators.

For reasons of printing, the pictures and drawings may appear slightly different from the actual machine

parts, without however casing any confusion.

Special symbols and bold and/or Italic fonts are used to highlight important information, particularly with

regard to safety.

The current revision code is indicated at the bottom left corner of every page. The list of revised pages is

shown at the end of the manual.

1.4. WARRANTY

The warranty terms and conditions are stated below unless otherwise specified in the order confirmation.

This manual is the property of FIORENTINI S. p. A.

The reproduction of all or part of this manual or its transmission to third parties by any

mechanical or electronic means or otherwise is forbidden without written authorisation

from the manufacturer. This manual is supplied to customers in a single original copy

unless otherwise specified at the time of ordering.

This manual is supplied as an integral part of the machine and should remain with the machine if transferred

to a new owner. This manual should be kept in a safe location for the entire working life of the machine. The

purchaser is responsible for making this manual available to all users. If this manual is lost, a duplicate should be

obtained from FIORENTINI.

FIORENTINI S.p.a. will not be held responsible for any damages to persons and/or property resulting from

failure to comply with the instructions in this manual.

FIORENTINI reserves the right to introduce any required technical and commercial changes without prior

notice. Therefore, any data and information contained in this manual may be changed and/or updated.

MACHINE FEATURES AND TECHNICAL DATA

BIG 38/48

SCOPE OF THE WARRANTY

The machine has been designed and built for trouble-free use over several years. However, if any

malfunction occurs during the warranty period, FIORENTINI S.p.A. undertakes to repair or replace free of

charge any parts revealing damage or premature wear due to faulty materials, factory defects or incorrect

assembly. The warranty does not cover any parts with damage or premature wear due to:

 failure to observe the instructions contained in this manual;

 tampering or alterations made without FIORENTINI’s specific approval;

 use of non-original spare parts;

 worn replacement parts, such as brushes, squeegee blades etc.

For installed electrical parts and commercially available parts, FIORENTINI S.r.l. extends to purchasers the

same warranty terms granted to FIORENTINI itself by the suppliers of the parts.

WARRANTY PERIOD

The warranty is valid for 12 months, starting from the machine delivery date. This is a fixed warranty term

and may not be extended due to replacements or repairs carried out during the warranty period.

EXCLUSIONS

The warranty does not cover materials and components subject to normal wear (brushes, squeegee blades

etc.) and those whose working life cannot be determined beforehand.

WARRANTY APPLICATION TERMS

Defective components must be returned to FIORENTINI S.p.a. in order to establish the causes of any

defects discovered and determine warranty applicability. Repairs and replacement under warranty will be

carried out on FIORENTINI’s premises, by third parties or on the customer's premises. For services carried

out on the customer premises, power sources and any special equipment necessary for the repairs will have

to be provided by the customer.

PRODUCT RETURNS

Written approval must be obtained from FIORENTINI's Technical Support office before returning parts for

replacement or repair under warranty.

All defective parts must be carefully repacked in order to avoid damage during transport. Products must be

returned on a free-on-board basis, complete with:

 the serial number from the machine data plate (see point 2.1);

 the item code and installation position of the returned part, as given on the spare part list;

 a detailed description of the defect and the conditions under which it became apparent;

In the case of defective electrical or electronic components,

please return the parts separately from other materials, so that

waste containing dangerous substances can be segregated and

Waste Electrical and Electronic Equipment (WEEE) can be recycled

in accordance with Directive 2002/96/EC.

A missing machine data plate will result in immediate loss of any warranty rights.

1.5. DECLARATION OF CONFORMITY

The Declaration of Conformity is supplied with the purchased machine and the use and maintenance

manual.

MACHINE FEATURES AND TECHNICAL DATA

BIG 38/48

MACHINE FEATURES AND TECHNICAL DATA

BIG 38/48

2. MACHINE FEATURES AND TECHNICAL DATA

2.1. IDENTIFICATION

The machine is identified by an adhesive plate attached to the protective casing of the steering column,

which contains indelible data regarding “CE” marking.

The plate must never be removed and should always be kept legible. In case of damage,

a duplicate should be ordered. The machine cannot be sold without the plate.

2.2. DESCRIPTION AND COMPONENTS

The BIG 38/48 scrubber-dryer is designed to clean all flat surfaces by washing and then suctioning the waste

water. The scrubber-dryer has a drive system consisting of two gear motors installed on the rear wheels,

directly on the brushes and powered in turn by electric accumulators, as are the suction motors.

The machine uses three rotating brushes to clean the floor surfaces, assisted by the action of the water and

detergent. As the machine travels forward, the rear brush (squeegee), in contact with the floor, collects the

water, which is immediately conveyed by suction to the recovery tank.

The dashboard regulates all the machine functions and provides the operator with an LED system that

indicates the remaining battery capacity and any errors detected by the electronic board, which are displayed

as rapid flashes. All the main functions of the machine can be activated through the dashboard. In detail,

these include:

 raising, lowering and switching on the brushes;

 regulating the water delivery flow;

 starting the suction motors;

 lowering/raising the squeegee;

 turning the lights on and off;

 turning on the flashing beacon and the buzzer;

 starting and stopping the machine.

The load-bearing structure of the machine consists of a cold-galvanised or stainless steel chassis, which

prevents oxidation problems that could affect its reliability.

The machine comprises the following main components:

 a cold galvanized or stainless steel chassis;

Ing. O.Fiorentini S.p.A.

MADE

50030 Piancaldoli (FI)

IN ITALY

Mod

BIG38

S.N.

101

2008

rpm

3600

780

174

4.75

FIGURE 2.1

MACHINE FEATURES AND TECHNICAL DATA

BIG 38/48

 an ABS plastic washing liquid tank;

 an ABS plastic waste water recovery tank with flexible suction and drainage hoses;

 three washing brushes;

 a squeegee;

 one idle wheel;

 two drive wheels controlled by electric motors;

 the steering assembly;

 the driver’s seat.

In consideration of recent EU product safety concerns, FIORENTINI has designed and built this machine in

compliance with the safety and health requirements provided by the applicable Directives. High quality

materials, advanced technology and FIORENTINI’s experience have been combined to produce a machine

of high performance and reliability. Each machine undergoes rigorous testing during construction and careful

final inspection.

MACHINE FEATURES AND TECHNICAL DATA

BIG 38/48

2.3. TECHNICAL DATA SHEET

The specifications provided above are not binding on the manufacturer and may therefore be

changed without notice. FIORENTINI can be contacted at any time for further information

(see point 6.1.).

UNIT OF MEASUREMENT CONVERSION TABLE

Length

1 inch = 1” = 25.4 mm

Power

1 kW = 1.36 CV = 1.34 BHP

Temperature

T (K) = t (°C) + 273 / t (°F) = 1.8 t (°C) + 32

Pressure

1 bar =100 kPa = 14.5 psi

MODEL

BIG 38

BIG 48

MAIN SPECIFICATIONS

Total working width

950 mm

1150 mm

Maximum output per hour

5700 m²/h

6900 m²/h

Maximum working autonomy

5-6 h

5 h

Solution tank capacity

300 l

Recovery tank capacity

300 l

300l

GENERAL SPECIFICATIONS

Traction (front/rear)

rear

Type of traction

Two electric gear motors

Travel speed

0/6 km/h

Max. gradient with a full load

12%

Depression

1600 mBar

Brush head pressure

0/100 kg

Noise (operator’s ear)

<75 dB

Minimum turning radius

2450 mm

2800 mm

ELECTRICAL SYSTEM

Power supply voltage

36V

Suction motor

2x 850W

Brush motors

3x 750W

Drive motors

2x 750W

Power supply

36V - 450A/h

DIMENSIONS AND WEIGHT

Length

1800 mm

Width

1000 mm

Height

1820 mm

Number/diameter of brushes

3x Ø330 mm

Squeegee width

1300 mm

1470 mm

Battery weight

530 kg

SAFETY

BIG 38/48

3. SAFETY

3.1. INTENDED USE

The BIG 38/48 is a floor scrubber-dryer machine designed and built for use in

industrial environments for washing and drying, with waste water removal, of flat

horizontal surfaces or sloping surfaces with gradients not exceeding 12%.

3.2. IMPROPER USE

 machine operation by unauthorised personnel;

 washing uneven and/or bumpy surfaces;

 washing of sloping surfaces;

 washing of surfaces with a gradient exceeding 12%;

 performing U-turns on a slope exceeding 5% and with a speed of over 1 km/h;

 using the machine in environments containing dangerous substances, and

particularly in explosive atmospheres or unsuitable microclimatic conditions;

 cleaning machine surfaces in the presence of flammable substances;

 use of the machine as a means of transport for people or other vehicles;

 modifying or tampering with the protection devices;

 charging the batteries in locations with insufficient ventilation;

 failure of operators to comply with current safety regulations/procedures;

 fitting equipment/devices likely to interfere with machine operation;

 introducing changes or alterations not authorised by FIORENTINI;

 using acid solutions likely to damage the machine;

 failure to comply with the specifications of the use and maintenance manual.

The information labels placed on the machine should be read carefully and should not be

covered for any reason. FIORENTINI shall assume no liability in any case of improper use

of the machine as described above.

3.3. RECOMMENDED EQUIPMENT

To make the best use of your machine, equipment specially designed and tested by Fiorentini and original

spare parts should be used. The FIORENTINI S.p.A. technical department is available to customers to meet

any design needs concerning parts and components required for a particular use of the machine.

SAFETY

BIG 38/48

3.4. OPERATOR QUALIFICATIONS

The table below shows the operator qualifications required based on the type of operation to be performed.

TYPE OF OPERATION

OPERATOR QUALIFICATIONS

Driving/control

Trained operator

Installation/removal

Fiorentini technician

Maintenance of mechanical parts

Fiorentini technician

Maintenance of electrical parts

Fiorentini technician

Cleaning maintenance

Trained operator

Dismantling and scrapping

Fiorentini technician

The personnel assigned to operating the machine should be specifically trained, particularly in regard to

safety issues; machine operators must have read and understood this manual.

FIORENTINI declines all liability for accidents involving persons or property caused by

unqualified and unauthorised operators.

3.5. SAFETY AND WARNING DEVICES

 Tampering with safety devices, and their removal or deactivation while the machine

is in operation, is strictly prohibited.

 The efficiency of safety and warning devices should be regularly checked (see point

5.1.).

Front brush guards

The BIG 38/48 machine has three nylon bristle brushes that rotate during

normal operation. Access to hazardous areas is prevented by plastic casing

that serves as a guard. The guard can only be removed intentionally. Removal

of a fixing element will obviously cause detachment of the guard from the

machine.

Warning devices

The BIG 38/48 machine is fitted with various warning devices to alert anyone

who happens to be within the working range of the machine:

 a horn-type acoustic signal to alert any persons in the vicinity of the

machine during normal use;

 an acoustic warning signal (buzzer) that sounds whenever the reverse

gear is engaged;

 a signal light with a yellow flashing beacon to indicate that the machine

is in operation.

SAFETY

BIG 38/48

SAFETY PLUG

The BIG 38/48 machine has a safety plug that connects the power supply batteries to the rest of the

machine. The plug is disconnected by pulling on the handle, which brings all machine functions to an

immediate halt. Operators should therefore familiarise themselves with use of the safety plug, as it provides

the most complete prevention and protection system. Use of the emergency plug should therefore be

automatic in situations of real or presumed emergency.

Pull in the case of

emergency

3.6. RESIDUAL RISKS

Starting from the design phase, FIORENTINI has analysed all the possible hazards related to use of the

machine in order to eliminate or at least minimise any risk of injury to machine operators. Warning signs and

indications regarding the accident-prevention systems and procedures to be used have been provided for

machine operators in order to minimise residual risks.

RISK OF CRUSHING

Risk of crushing is present:

 when replacing the front brushes;

 when checking the brushes in the suction motor;

 when adjusting the squeegee;

When replacing the brushes and adjusting the squeegee, the operator must ensure that the ignition

key is not inserted in the dashboard in order to prevent accidental starting of the machine.

This hazard is indicated by pictograms on the brush guards and recovery tank.

RISK OF OVERTURNING

Risk of overturning is present:

during normal use of the machine when the slope limits specified under improper use of the

machine are exceeded and when the machine is used to clean surfaces that are uneven or have

holes and depressions (see 3.2).

SAFETY

BIG 38/48

Do not use the machine to wash surfaces with gradients exceeding 12% or bumpy or

uneven surfaces likely to affect its stability.

FIORENTINI declines all liability for accidents involving persons or property caused by use of

the machine on surfaces that can compromise its stability. The buyer must put suitable signs

in place to inform the user of the state and condition of the surfaces to be cleaned.

3.7. SAFETY SIGNS

These include signs indicating:

HAZARDS

These signs are triangular with black

pictograms on a yellow background

PROHIBITIONS

These signs are round with black pictograms

on a white background with a red stripe

What is this?

This sign indicates the risk of crushing by moving parts inside the

machine.

What should

I do?

During installation or maintenance work, ensure that the ignition key

has been removed from the dashboard.

What is this?

This sign prohibits the removal of guards covering moving parts.

What should

I do?

Before removing guards for installation or maintenance work, always

ensure that the ignition key has been removed from the dashboard.

During operation, keep body parts clear of the machine and ensure

that the guards are securely in place.

SAFETY

BIG 38/48

If any signs become damaged, the purchaser must replace them with identical ones.

It is strictly forbidden to remove or tamper with these signs.

What is this?

This sign indicates risk of crushing due to closure of the recovery

tank. This can be tipped to one side along the longitudinal axis of the

machine to facilitate cleaning of the tank and to provide access to the

battery.

What should

I do?

Take particular care during maintenance and, if necessary, provide a

suitable support.

SAFETY

BIG 38/48

If any signs become damaged, the purchaser must replace them with identical ones.

It is strictly forbidden to remove or tamper with these signs.

What is this?

This sign indicates risk of crushing during maintenance by the suction

motors.

What should

I do?

Take particular care to ensure that the key is not inserted in the

dashboard and that the motor protection cover does not tip over.

START-UP AND OPERATION INSTRUCTIONS

BIG 38/48

4. START-UP AND OPERATION INSTRUCTIONS

4.1. TRANSPORT AND HANDLING

The machine is delivered to the purchaser fully assembled, in special packaging whose features are indicated in

figure 4.1 below. The centre of gravity is marked by a black arrow on the packaging. The forks of the forklift or

pallet truck must be positioned with the black arrow centred between them. The package must be handled with

extreme care. Do not stack one package on top of another.

If agreed with the purchaser, the machine can be delivered without packaging, placed on a pallet and secured

by means of straps.

The purchaser should check upon delivery that the machine has not been damaged during

transport and that all the material listed in the transport documentation has been received;

otherwise, the forwarders and manufacturer should be promptly informed.

Unless otherwise agreed, purchased goods will travel at the purchaser's own risk.

Handling must be performed with appropriate lifting equipment and devices, as indicated in the following table.

Always ensure that the elevator forks and harness straps are placed so that the black arrow on the packaging is

centrally positioned in relation to the lifting system. Anchor and/or harness points must be arranged so that the

machine remains in a stably balanced position during lifting.

TYPE OF PACKAGING

LIFTING EQUIPMENT AND DEVICES

FIG.

Cardboard or plywood box on a

pallet

Forklift truck

4.2

None

Forklift truck/mobile crane with two slings and a spreader bar

4.3

FIGURE 4.1

1080

1840

850

1850

START-UP AND OPERATION INSTRUCTIONS

BIG 38/48

The slings used must be of a suitable capacity for the load. All handling operations

should be performed very slowly to prevent the load from swinging or tipping. Any

improper handling manoeuvres could damage the machine or expose operators to risk.

For the machine dimensions and weight, see point 2.3 Handling of the machine should

only be carried out by authorised personnel trained in the use of lifting equipment.

LOADING DIAGRAM

4.2. STORAGE

If the machine is not installed immediately, it should be stored in an enclosed, dry location to ensure the proper

preservation and efficiency of all its components. Relative humidity must be below 80% and the storage

temperature must be between 3°C  and  + 45 °C.

4.3. UNPACKING THE MACHINE

 Cut the strapping with care so that it does not spring up;

 Remove the staples on the base connecting the box to the pallet

 If the package is made of plywood, remove the staples from the sides and base of each panel;

 Cut the strapping holding the machine in place;

 Place the machine on the ground.

4.4. HANDLING THE UNPACKED MACHINE

When handling the machine for short transport after use, disconnect the battery cables and remove the

brushes and squeegee; for longer transport, repack the machine in the original box.

FIGURE 4.2

FIGURE 4.3

START-UP AND OPERATION INSTRUCTIONS

BIG 38/48

4.5. INSTALLATION

Installation must be performed by authorised personnel with knowledge of the instructions

contained in this manual.

The BIG 38/48 floor scrubber-dryer can only be put into service when there is absolute certainty that all its

components and devices are in good working condition. For this purpose, FIORENTINI's specialised technicians

conduct rigorous testing during manufacture and a thorough final inspection of each machine.

4.5.1 BATTERY INSTALLATION

For installation of the batteries, follow the instructions given below:

 raise the recovery tank to access the battery compartment (detail 1 figure 4.4);

 install the battery box in the provided compartment (detail 2 figure 4.4), making sure there are no cracks

in the battery containers;

 never add distilled water after recharging the batteries;

 clean the connection surfaces;

 the battery must be handled using appropriate lifting gear (see 2.3 for the weight of the battery).

FIGURE 4.4

START-UP AND OPERATION INSTRUCTIONS

BIG 38/48

4.6. CONTROL AND MONITORING DEVICES

4.6.1 DASHBOARD

The dashboard features a series of switches and indicator lights that activate/deactivate the various functions of

the machine. Each switch has a pictogram that clearly represents its function. The dashboard is illustrated in

figure 4.5 and the function of each switch is described in the table below.

POS.

BUTTON

FUNCTION

BRUSH MOTOR PROTECTOR

SUCTION MOTOR LIGHT

ROTATING BEACON SWITCH

BRUSH ROTATION STOP

HORN

FIGURE 4.5

1 2 3 4 5 6 7

8 9 10 11 12 13

START-UP AND OPERATION INSTRUCTIONS

BIG 38/48

FORWARD/REVERSE GEAR SELECTOR

BATTERY INDICATOR

SUCTION MOTOR PROTECTOR

RAISE/LOWER BRUSHES

1 0

SQUEEGEE SUCTION SWITCH

1 1

LIGHT SWITCH

1 2

FUSE

1 3

KEY SWITCH

An emergency button is installed on the left side of the fairing on the BIG 38/48 floor scrubber-dryer for use

whenever a situation of real or presumed danger arises. Pressing the emergency button immediately stops all

machine functions. Once the problem has been resolved and the machine is ready for use, it can be restarted

simply by returning the emergency button to its original position. (see figure 4.6).

Push in case of

emergency

FIGURE 4.6

Page is loading ...

FIORENTINI BIG 48 Instructions For Use And Maintenance Manual

Brand: FIORENTINI

Model: BIG 48

Category: Scrubber

Type: Instructions For Use And Maintenance Manual

This manual is also suitable for

BIG 38

Variable speed control allows the operator to adjust the speed of the machine to suit the cleaning task.
Self-propelled drive makes it easy to maneuver the machine around obstacles.

Download PDF

report