RocketFish RF-RBKIT Quick Setup Manual

Brand: RocketFish

Model: RF-RBKIT

Category: Headphones

Type: Quick Setup Manual

RocketFish RF-RBKIT lets you enjoy your home theater's surround sound wirelessly. Connect the sender to your home theater system and the receiver to your surround sound speakers. Use the sender's Speaker-In or Pre-In connectors depending on your need. Adjust the audio level on the receiver and enjoy your favorite movies and music without the hassle of wires.

RF-RBKIT Wireless HD Audio Starter Kit

QUICK SETUP GUIDE

Initial setup

1 Unpack the package contents.

2 Enable the remote control battery.

Remove the tab from the bottom

of the remote control.

3 Set up the Wireless HD Audio Starter Kit.

The diagram shows a typical RF-RBKIT

application for home theater

wireless surround sound. The

wireless sender is connected to

the surround sound speaker

outputs of your home theater

system and the wireless receiver

is connected to the surround

sound speakers. The RF-RBKIT

could similarly be used to send

audio from your A/V receiver or

other audio component to other

rooms in your house.

See the following steps for

further setup details.

Package contents

Wireless sender AC power adapter

(for wireless sender)

Remote control 3.5 mm to RCA adapters (2)

(6 inches/15.25 cm)

(for wireless sender)

Wireless receiver

AC power cable

(for wireless receiver)

3.5 mm stereo cables (2)

(for wireless sender) Establishing communication

The sender and receiver packaged together with the RF-RBKIT were pre-joined so they will

communicate with each other right out of the box. So if this is your rst Rocketboost enabled

product you can skip this step and go to the next section, Using your wireless sender and receiver

step.

If you need to rejoin the sender and receiver, and this is your only Rocketboost enabled product,

then use the following steps.

1 Set the HUB STATUS switch on the wireless sender to ENABLE if this is your rst Rocketboost

product set.

• The power indicator turns green when the HUB STATUS switch is set to ENABLE.

• The power indicator turns blue when the HUB STATUS switch is set to DISABLE.

2 Press and hold on the wireless sender for more than three seconds to put it into joining

mode. The power indicator starts blinking rapidly and the unit will stay in joining mode for 30

seconds.

3 Press and hold the on the wireless receiver for more than three seconds so the sender and

receiver enter joining mode.

• The power indicator lights steadily if the joining was successful.

• The power indicator blinks slowly if the joining was not successful.

If you already have other Rocketboost devices you need to join both the sender and the receiver to

your existing hub device. See the User Guide for detailed instructions on how to do this.

Using you wireless sender and receiver

1 Turn on the wireless sender and wireless receiver. The power indicator LEDs should light

steadily. If they are blinking you need to rejoin the sender and receiver. See the Establishing

communication step above.

2 Turn on the audio source connected to the wireless sender. Make sure the volume of the audio

source is not muted, otherwise no audio will be sent over the Rocketboost network.

3 Press the SOURCE A or B button on the wireless sender to turn on the source from the A or B

inputs, depending on which input you want to listen to. The LED around the source button

turns on to show that the source is enabled.

4 Adjust the audio level on the wireless receiver. If you have multiple audio sources in your

Rocketboost network, press the SOURCE button on the wireless receiver to hear the next audio

source. Press the SOURCE button again to cycle through all available audio sources.

Rocketboost network notes:

Every Rocketboost network must contain

one hub device, which helps devices join

the network. The network can have only

one hub, which you can enable using the

hub switch on the back of all Rocketboost

senders and sender/receivers. If this is your

rst Rocketboost product, you should

make this device the hub, if you already

have Rocketboost products, you should

disable hub mode on this device.

Important: Hub devices must always have

power for your network to operate. The

hub device can be in standby (power-

saving) mode, but must stay plugged in.

ENGLISH 10-0174

Connecting the wireless sender

Note: The sender supports two audio sources, which are labelled A and B. For each audio source

you can use either the Speaker-In or Pre-in (line level) connectors, depending on your need. For

example, when using the sender with a home theater system amplier, it is convenient to use the

Speaker-In connectors. When using the sender with a TV or MP3 player, use the Pre-In connectors.

Connecting to the Speaker-In connectors (such as

home theater surround sound) or Pre-In connectors

Note: The diagram and following step are for home theater

wireless surround sound. If you want to listen to your home

theater main channels in another room, connect the left

and right channels of the home theater system instead of

the surround channels.

1 Connect the right surround speaker terminals of your

home theater system to the right speaker terminals of

the sender by connecting the red speaker wire to the

red (+) terminals, and the black speaker wire to the

black (-) terminals. Repeat to connect the left surround

speaker terminals.

2 If you are connecting to the Pre-in connectors,

connect external audio source(s) to the Pre-in A

and/or B jacks on the rear of the sender using

the 3.5 mm stereo cable. If necessary, you can

also use the 3.5 mm to RCA adapter, if your audio

device uses RCA type line out connectors.

3 Connect the AC power adapter to the sender

and plug into an AC power outlet.

Connecting the wireless receiver

Note: You can use the receiver for wireless surround sound or to listen to your music in another

room in your house.

1 Connect the right speaker to the right

speaker-out connectors on the receiver.

Use a red speaker wire to connect the red

(+) speaker-out connector and a black

speaker wire to connect the black (-) speaker-out connector.

Repeat this step to connect the left speaker.

2 Connect one end of the AC power cord to the AC IN connector on the back of the receiver.

Then, plug the other end of the AC power cable into an AC power outlet. The Standby indicator

turns on.

Cable spool

(for wireless receiver)

Speaker cable (4)

3 ft (91.5 cm) User Guide Quick Setup Guide

Wireless sender

Wireless receiver

Home theater

system

Back of home theater system

Back of wireless sender

SPEAKER-OUT (4-8 Ohm)

120V~,60Hz

AC IN

Back of wireless sender

To headphones or line out

audio jacks of your TV,

DVD, MP3, or other audio

source component

Speaker Speaker

Back of wireless receiver

RocketFish RF-RBKIT Quick Setup Manual

Brand: RocketFish

Model: RF-RBKIT

Category: Headphones

Type: Quick Setup Manual

Download PDF

report

RocketFish RF-RBKIT Quick Setup Manual

RocketFish RF-RBKIT Quick Setup Manual

Related papers

Other documents