Assembly Instructions
Product Dimensions:
78” L x 42.5” D x 43.25” H
Please take a moment to read through the entire instruction booklet before assembly to
familiarize yourself with this product. Once you feel ready to start, follow the instructions
step by step and this should make this process as easy as we could make it for you.
Page 1 of 12
Low Loft Bed with Ladder
If you need help or have damaged or missing parts, contact customer service
All Rights Reserved.
Page 2 of 12
ADULT ASSEMBLY REQUIRED
CHOKING HAZARD
•
•
USE, MAINTENANCE & ASSEMBLY
PARENTAL SUPERVISION IS REQUIRED
WARNING CAUTION
STRANGULATION HAZARD
SAFETY WARNINGS
•
•
•
•
•
•
•
•
SIZE OF MATTRESS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
This product includes small parts, sharp points and sharp edges in its unassembled state.
Keep unassembled parts away from children under 3 years of age, and animals.
Never attach or hang items to any part of the loft bed that are not designed for use with
the bed; for example, but not limited to hooks, belts, and jump ropes.
A twin size mattress of 75” Length x 39” Width x 6 Inch Thickness (190.5 x 96.5 x 15.24 cm)
is recommended. Surface of mattress must be at least 5 inches (12.7 cm) below upper edge
of guardrails. Maximum mattress and foundation combined thickness of 8 inches (20.3 cm).
Follow the information on the warnings appearing on the loft bed end structure and on the
carton. Do not remove warning label from bed.
Always use the recommended size mattresses or mattress supports, or both, to help
prevent the likelihood of entrapment or falls.
Surface of mattress must be at least 5 inches (127 mm) below upper edge of guardrails.
Do not allow children under 3 years of age to use the loft bed.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the loft bed.
Always use guardrails on both long sides of the loft bed. If the loft bed will be placed next to
the wall, the guardrail that runs the full length of the bed should be placed against the wall
to prevent entrapment between the bed and wall.
The use of water or sleep flotation mattresses is prohibited.
Periodically check and ensure that the guardrail, ladder, and other components are in
their proper position, free from damage, and that all connectors are tight.
Use on level surfaces only. Assemble on a soft level surface to avoid damage to unit or floor.
Do not use this item if any components are missing or damaged.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Only clean using damp cloth and mild detergent, do not use bleach or abrasive cleaners.
Check you have all components and tools listed on page 4
Do not stand or put weight on this product during assembly, this could cause damage.
Remove all hardware from the plastic bags and separate them into groups.
Assemble the item as close to its final position (in the same room) as possible.
Certain assembly steps may be easier with 2 people.
Dispose of all packaging carefully and responsibly.
We do not recommend power screwdrivers. Only use hand screwdrivers to prevent
damage to unit.
•
!
This product is intended for child use age 3+.
Parents or Guardians should supervise use under the intended age specifically regarding
children that may have access to it and climb on the unit.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
If used improperly, your low loft bed may be pulled over or fall, creating risk of injury or
damage. Children should not be permitted to climb or pull on the low loft bed.
Always use the ladder for entering or exiting the loft bed.
This drawing is to give you an overall idea only of how this assembly will go together and does
not replace the assembly instructions.
Please take a moment to read through the whole instruction booklet before assembly to familiarize
yourself with this product . Once you feel ready to start, follow the instructions step by step and this should
mak e this process as easy as we could make it for you.
Due to the number of parts involved
assembly can take a few hours
so set aside between 2 and
3 hours to assemble this
without rushing.
ASSEMBLY AT A GLANCE
Page 3 of 12
1
2
3
4
5
5
6
6
6
6
13
12
14
14
11
15
15
15
15
16
10
10
7
8
9
9
17
Phillips Screwdriver
(Medium)
COMPONENT PARTS
Please check that you have all the parts listed below
Medium Long Bolt
M6x55mm x 2
Screw
x 26
ASSEMBLY HARDWARE
FE
Barrel Nut
G
x 26 x 1
Allen Wrench
H
*Note: follow the setup of
of Option 1 for ladder right
conguration or Option 2
for ladder left conguration.
Each leg is unique.
1. Leg x1
2. Leg x1
3. Leg x1
4. Leg x1
5. Head/Footboard x2
6. End Rails x4
7. Ladder side board x1
8. No ladder side board x1
9. No ladder side rails x2
10. ladder side rails x2
11. Rear Leg Support x1
12. Right ladder rail x1
13. Left ladder rail x1
14. ladder rung x2
15. rail support x3
16. rail support by ladder x1
17. bed slats x13
7
9
8
10
11
12
13
4
3
2
1
14
16
5
15
6
17
Allen Wrench
(included)
Wood Dowel Pin
x 30
Short Bolt
M6x80mm x 24
B
A
Long Bolt
C
M6x25mm x 17 M6x30mm x 6
Medium Short Bolt
D
Page 4 of 12
TOOLS REQUIRED
ASSEMBLY INSTRUCTIONS
2
1
Select 1, 2, 5, 6 x2, A x6, B
x6, F x6. On at surface posi-
tion 6 x2, and part 5 below 6.
See Iarge view - Insert F
Barrel Nut into 6 while facing
the threaded opening
toward the end. Repeat F x5
in 6 and 5. Insert A x6 in top
holes at ends of 6, and 5.
Insert top 6 A dowel into top
hole of 1. Insert B Bolt
through 1 into hole of 6 and
tighten with H allen wrench
into barrel nut F. Repeat for
other 6 and 5. Repeat A x3
and B x3 for leg 2.
Page 5 of 12
1
2
F
A
F
A
F
B
B
6
6
5
H
B
A
A
B
6
6
5
F
F
3
4
Select 3, 4, 5, 6 x2, A x6, B
x6, F x6. On at surface posi-
tion 6 x2, and part 5 below 6.
Insert F Barrel Nut into 6
while facing the threaded
opening toward the end.
Repeat F x5 in 6 and 5. Insert
A x6 in top holes at ends of 6,
and 5. Insert top 6 A dowel
into top hole of 3. Insert B
Bolt through 3 into hole of 6
and tighten with H allen
wrench into barrel nut F.
Repeat for other 6 and 5.
Repeat A x3 and B x3 for leg
4.
ASSEMBLY INSTRUCTIONS
4
3
Select 9 x2, 8, 11, 7, A x10, B
x10, F x10. Insert A x2 into
bottom holes in ends of 9.
Insert F x2 into inside holes in
9. With F towards center, insert
B through top hole of 3 and
into 9 and secure to F. Finger
tighten. Support 9 and 3 and
repeat hardware steps at other
end of 9 securing to leg 2.
Repeat hardware steps for part
11 at bottom of 2 and 3. Select
7 and with bottom of “L” shape
facing down and to center,
attach 7 to 1 and 4 with A, B &
F. Attach 2nd 9 board same as
previous 9 just lower. Repeat
steps for 7 for board 8 to leg 2
and 3. Use H allen wrench and
tighten all B on all 4 legs.
Select ladder parts 13
(left), 12 (right) and 14
x2, A x4, D x4. Insert A
into bottom holes of 14.
Repeat for other 14.
Insert D through top
hole in 12 and into end
of 14 and nger tighten.
Repeat for other end to
13. Attach other 14 using
same hardware steps to
bottom of 12 and 13. Use
H allen wrench to tighten
all D bolts.
Page 6 of 12
A
A
B
B
B
B
B
B
A
A
2
1
9
9
8
11
F
F
F
74
3
A
A
A
14
14
13
12
D
D
D
D
F
F
ASSEMBLY INSTRUCTIONS
6
5
Option 1 - Ladder Right
Side. Select 10 x2, F x4,
Bx2, A x2. Insert A into
bottom holes of 10.
With F holes inside,
support other end of 10
and attach 10 to leg 1
with B bolt and nger
tighten. Continue sup-
port top board 10 other
end, repeat and attach
other board 10.
Do not stop support of
either board. Option 2 -
Left Ladder - ax 10s
to leg 4 instead of 1.
Option 2 Left Ladder- Skip
to Step 8.
Option 1 - Bring in the
ladder assembly and with
13 (facing ladder - left). Still
supporting 10s, use C x2,
and insert C through last
hole of 7 by leg 4 and into
12 and nger tighten.
Repeat C through 7 into 13.
Select A x2, D x2 and insert
A into ends of 10 x2. Insert
D through top hole of 13
and into 10 and nger
tighten. Repeat D for
bottom hole on 13. Insert D
through top hole of 12, and
nger tighten. Insert D at
bottom hole of 12 (between
14s). Use H and tighten 2 Cs
in 7, 2 Ds in 12, 2 Ds in 13.
Page 7 of 12
A
B
F10 10
A
D
D
D
A
D
CC
1
10
10
7
ASSEMBLY INSTRUCTIONS
7
Select 15 x4, 16, Cx15.
Attach 16 with C to 10s
and 7 near ladder. Use C
and attach 15s in other
holes of 10 and 7. Use
Cs and repeat for 15s x2
into back side 9s and 8.
Use H to tighten all C
bolts.
Option 1 - Ladder Right
Skip to step 10.
Page 8 of 12
D
D
C
C
15
15
15
15
16
C
DA
8
Option 2 - Ladder Left.
Bring in the ladder assembly
and with 13 (facing ladder -
left). Still supporting 10s,
use C x2, and insert C
through rst hole of 7 by leg
1 and into 13 and nger
tighten. Repeat C through 7
into 12. Select A x2, D x2
and insert A into ends of 10
x2. Insert D through top
hole of 12 and into 10 and
nger tighten. Repeat D for
bottom hole on 12. Insert D
through top hole of 13, and
nger tighten. Insert D at
bottom hole of 13 (between
14s). Use H and tighten 2 Cs
in 7, 2 Ds in 12, 2 Ds in 13.
ASSEMBLY INSTRUCTIONS
9
Option 2 - Ladder Left.
Select 15 x4, 16, Cx15.
Attach 16 with C to 10s
and 7 near ladder. Use C
and attach 15s in other
holes of 10 and 7. Use
Cs and repeat for 15s x2
into back side 9s and 8.
Use H to tighten all C
bolts.
C
C
15
16
15
15
15
10
Select 17 x13, G x26.
Align 17 and space
them evenly over
bottom of “L” shape on
7 and 8. Rest 17 ends on
7 and 8. Screw G
through end of 17 into
7 and tighten. Repeat
for other end of 17 into
8. Repeat for other 12
boards. Safety check
all boards are secure.
Add your mattress (not
included) and follow
warning labels for
mattress size on part 6.
G
G
Page 9 of 12
BED FRAME ASSEMBLY COMPLETE
Page 10 of 12
11
Follow steps 11 to
13 to continue
assembly of the low
loft bed set. Final
position bed frame
in room. Insert
drawer chest under
bed frame by ladder
on long side. Insert
bookcase near
ladder on short side.
ASSEMBLY INSTRUCTIONS
Option 1 - Ladder
Right side. Align the
desktop to both tracks
on the underside of
the bed frame. Insert
and slide the desktop
into the tracks at the
same time.
*See Desk
Instructions for
more details.
Option 2 - Ladder left
side. Move the desk
tracks to the other bed
end. Align the desktop
to both tracks on the
underside of the bed
frame. Insert and slide
the desktop into the
tracks at the same time.
*See Desk
Instructions for
more details.
13
12
Page 11 of 12
ASSEMBLY COMPLETE
Page 12 of 12
CONGRATULATIONS, YOUR LOW LOFT BED
WITH LADDER IS COMPLETE!
Assembly Instructions
Product Dimensions:
36” L x 10” D x 26” H
Please take a moment to read through the entire instruction booklet before assembly to
familiarize yourself with this product. Once you feel ready to start, follow the instructions
step by step and this should make this process as easy as we could make it for you.
Page 1 of 7
Low Loft Bed - Bookcase
If you need help or have damaged or missing parts, contact customer service
All Rights Reserved.
Page 2 of 7
ADULT ASSEMBLY REQUIRED
CHOKING HAZARD
•
•
USE, MAINTENANCE & ASSEMBLY
PARENTAL SUPERVISION IS REQUIRED
WARNING CAUTION
STRANGULATION HAZARD
SAFETY WARNINGS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
This product includes small parts, sharp points and sharp edges in its unassembled state.
Keep unassembled parts away from children under 3 years of age, and animals.
Never attach or hang items to any part of the bookcase that is not designed for use with
the bookcase; for example, but not limited to hooks, belts, and jump ropes.
Follow the information on the warnings appearing on the loft bed end structure and on the
carton. Do not remove warning label from bed.
Do not allow children under 3 years of age to use the bookcase.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Children have died from furniture tip-over.
To reduce the risk of furniture tip-over:
ALWAYS install tip-over restraint especially if used by a wall or in the open.
NEVER put a TV on this product
NEVER allow children to stand, climb or hang on drawers, doors, or shelves.
NEVER open more than one drawer at a time.
ALWAYS place heaviest items in lowest drawers.
Periodically check and ensure that the components are in their proper position, free from
damage, and that all connectors are tight.
Use on level surfaces only. Assemble on a soft level surface to avoid damage to unit or floor.
Do not use this item if any components are missing or damaged.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Only clean using damp cloth and mild detergent, do not use bleach or abrasive cleaners.
Check you have all components and tools listed on page 4
Do not stand or put weight on this product during assembly, this could cause damage.
Remove all hardware from the plastic bags and separate them into groups.
Assemble the item as close to its final position (in the same room) as possible.
Certain assembly steps may be easier with 2 people.
Dispose of all packaging carefully and responsibly.
We do not recommend power screwdrivers. Only use hand screwdrivers to prevent
damage to unit.
•
Enfants morts suite au basculement d’un meuble.
Afin de limiter le risque de basculement de meuble:
TOUJOURS utiliser les fixations anti-basculement.
NE JAMAIS installer de TV sur ce produit.
NE JAMAIS laisser d’enfants se tenir debout sur les tiroirs,
portes ou etageres, y grimper ou s’y suspendre.
NE JAMAIS ouvrir plus d’un tiroir a la fois.
TOUJOURS placer les choses les plus lourdes dans les tiroirs du bas.
Han muerto ninos por el vuelco de meubles.
Para limitar el riesgo de vuelco de los meubles:
Utilisar SIEMPRE las fijaciones antivuelco que suministran.
NUNCA instalar un TV sobre este producto.
NUNCA permitar que los ninos se pongan de pie, trepen o
se cuelguen de los cajones, puertas o baldas.
NUNCA abrir mas de un cajon a la vez.
Colocar los objetos mas pesados en los cajones inferiores.
•
•
•
•
•
•
•
•
•
•
!
FURNITURE TIP-OVER HAZARD
•
This product is intended for child use age 3+.
Parents or Guardians should supervise use under the intended age specifically regarding
children that may have access to it and climb on the unit.
Do not allow horseplay on, under, or behind the unit and prohibit jumping on the bookcase.
If used improperly, your bookcase may be pulled over or fall, creating risk of injury or
damage. Children should not be permitted to climb or pull on the bookcase.
This drawing is to give you an overall idea only of how this assembly will go together and does
not replace the assembly instructions.
Please take a moment to read through the whole instruction booklet before assembly to familiarize
yourself with this product . Once you feel ready to start, follow the instructions step by step and this should
mak e this process as easy as we could make it for you.
Due to the number of parts involved
assembly can take a few hours
so set aside between 30 minutes and
1 hour to assemble this
without rushing.
ASSEMBLY AT A GLANCE
Page 3 of 7
1
2
5
3
3
4
4
4
4
3
3
1
2
5
COMPONENT PARTS
Please check that you have all the parts listed below
ASSEMBLY HARDWARE
x 1
1. Left Panel x1
2. Right Panel x1
3. Shelf x2
4. Back Support x2
5. Top Shelf x1
Hex Screwdriver
(included)
Hex Screw
7.0x50mm x 12
Screw
x 20
B
A
Wood Dowel Pin
C
4.0x30mm x 4
Hex Screwdriver
D
Page 4 of 7
Hammer
(not included)
1
1
3
4
4
5
5
2
2
Phillips Screwdriver
(Medium)
TOOLS REQUIRED
ASSEMBLY INSTRUCTIONS
2
1
Select 4 x2, 3 x2, 5,
B x20. Insert B x4
into ends of 4.
Repeat for 2nd 4.
Insert B x4 into
inner larger holes
on ends 3. Repeat
for 2nd 3, and 5.
Page 5 of 7
Select 1, 3 x2, 4 x2, 5, A
x6. Position 1 left.
Note, the top of 1 the
holes are close to the
end and the bottom
holes are further away
from the end. Position
3 with the holes on the
long side facing down-
ward at bottom of 1.
Position 4 above 3 at
the back. Repeat 2nd 3
and 4 in the center.
Position 5 at the top.
Align 4 Bs into holes
on 1. Insert A x2 into
bottom holes in 1 and
into 3. Repeat for 5,
and 2nd 3. Tighten A
screws with D wrench.
3
4
5
4
B
3
5
4
3
4
3
B
3
3
1
4
4
5
A
D
BACK
TOP
BOTTOM
D
A
A
A
4
4
4
5
3
3
1
ASSEMBLY INSTRUCTIONS
4
3
Select 2, A x6. Note the top
of board 2 has the holes
close to the end. Position 2
with the top holes upward
towards 5 and bottom holes
toward 3 and 4. Align 4 Bs
into holes in 2. Insert A into
bottom hole in 2 and into 3.
Repeat insert A for other
bottom hole of 2 into 3.
Repeat A screws for 2nd 3
and 5. Tighten all A screws
with D Hex wrench.
Select C x4. Insert C in
bottom holes under-
neath 3 x2 (at the back)
and tighten with stan-
dard screwdriver (not
included). Repeat for
other board 3 with C x2.
Page 6 of 7
3
1
2
5
5
3
3
2
1
4
4
D
A
A
TOP
BOTTOM
3
TOP
BOTTOM
C
3
ASSEMBLY COMPLETE
Page 7 of 7
IF YOU HAVE ORDERED THE SET, PLACE THE
BOOKCASE AT THE END NEAR THE LADDER.
CONGRATULATIONS, YOURLOW LOFT BED -
BOOKCASE IS COMPLETE!
Assembly Instructions
Product Dimensions:
38” L x 27” D x 26” H
Please take a moment to read through the entire instruction booklet before assembly to
familiarize yourself with this product. Once you feel ready to start, follow the instructions
step by step and this should make this process as easy as we could make it for you.
Page 1 of 11
Low Loft Bed - Hide-a-Desk
If you need help or have damaged or missing parts, contact customer service
All Rights Reserved.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
HOMESTOCK 99892 User guide
- Type
- User guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI