Mitsubishi AG-150A User manual

Brand: Mitsubishi

Model: AG-150A

Category: Split-system air conditioners

Type: User manual

This manual is also suitable for

Air-conditioner Network System

Centralized Controller

AG-150A

GB-50ADA-A

GB-50ADA-J Instruction Book

(Web browser for Initial Settings)

Contents

1 Introduction ..........................................................................1

1-1 Terms Used in This Manual ....................................................1

1-2 Computer Requirements .........................................................1

1-3 Notes on using AG-150A with the integrated centralized control

software (TG-2000A)................................................................1

2 Setting the Operating Environment......................................2

2-1 Setting the PC IP Address.......................................................2

2-2 Setting the Web Browser.........................................................4

2-3 Setting the Java Execution Environment.................................6

3 Performing Operations.........................................................7

3-1 Logging in on the AG-150A.....................................................7

4 Initial Settings.....................................................................10

4-1 Setting the Current Date and Time........................................ 10

4-2 Setting the Basic Information and External Input Functions .11

4-3 Group Setting ........................................................................19

4-4 Interlocked Setting.................................................................21

4-5 Block Setting..........................................................................22

5 Functions 1.........................................................................23

5-1 Error mail reports/E-mail communication..............................23

5-2 Energy-Save Control and Peak Cut Control .........................26

5-3 Settings for measurement .....................................................31

6 Functions 2.........................................................................35

6-1 Limiting the Set Temperature Operating Range ...................35

6-2 Night Mode (Silent Mode) Schedule......................................36

6-3 System-Changeover of Y series............................................ 37

7 Functions 3.........................................................................38

7-1 External Temperature Interlock.............................................38

7-2 Night setback control.............................................................39

7-3 Interlock control.....................................................................40

8 User Setting .......................................................................48

9 Registering a License for Optional Function......................50

Before using the controller, please read this Instruction Book carefully to ensure correct

operation. Retain this manual for future reference. WT05491X06

Ver. 2.4

1 Introduction

Special features of Mitsubishi Electric Corporation’s “Centralized Controller AG-150A,” “Centralized Controller

GB-50ADA-A,” and “Centralized Controller GB-50ADA-J” are that a PC connected to a LAN can be used to

monitor the operation condition of air conditioners, perform air conditioner operations, and make initial settings.

This document explains the procedures for making initial settings for the Centralized Controller using the web

browser. Hereinafter, the centralized controller AG-150A, GB-50ADA-A, and GB-50ADA-J, unless otherwise

specified, will be called "AG-150A".

Note: License of "Web Monitor" or "Basic License Pack" is necessary to use the web browser (to operate or monitor the air

conditioners). Some licenses are necessary depending on the functions to be used. Register the license key on the LCD

screen or on the registration screen.

Note: A one-day license key can be registered on the LCD screen that allows the user to use the "Web Monitor" only on the day of

the registration (not applicable to GB-50ADA-A and GB-50ADA-J). Use this license key to use the initial setting browser, or

in any other situations when a temporary license key "Web Monitor" is necessary.

Note: Use a security device such as a VPN router when connecting the AG-150A to the Internet to prevent unauthorized access.

Note: "Booster unit" and "Water HEX unit" are referred to as "Air to water".

Note: As GB-50ADA-A and GB-50ADA-J are not equipped with a LCD for settings, the initial setting must be made on the Initial

Setting Web.

Note: GB-50ADA-A and GB-50ADA-J cannot be connected to the Expansion Controller (PAC-YG50ECA). Settings or displays of

the Expansion Controller cannot be made on the GB-50ADA-A and GB-50ADA-J.

1-1 Terms Used in This Manual

- “Click” refers to the action of positioning the mouse cursor on the object (such as button or folder), pressing

down, and releasing the left mouse button once.

- Unless otherwise specified, the example screen images used in this manual are Windows XP® and Internet

Explorer 6.0 screen images.

Note: Windows is a registered trademark or trademark of Microsoft Corporation USA in the United States and other countries.

1-2 Computer Requirements

To monitor and operate air conditioners by web browser, computer must include the following requirements.

Table 1-1 Computer Requirements

Item Requirement

CPU Pentium 300MHz or faster

Memory 64M Bytes or more (128M Bytes or more recommended)

Screen resolution 1024 x 768 or higher recommended

Compatible browser

Microsoft® Internet Explorer 6.0 or later

Note: You must have a Java execution environment

(Sun Microsystems Java® Plug-in Ver.1.6.0.02 or later).

Note: You can check the Sun Microsystems® Java Plug-in version in

“Java” in a control panel.

Note: When using Sun Microsystems® Java Plug-in Ver.1.6.0_10 or

later, set the Java execution environment according to the

instructions in section 2-3 “Setting the Java Execution

Environment.”

On-board LAN port or LAN card One connector (100BASE-TX)

Other Pointing device such as a mouse

Note: Microsoft is a registered trademark or trademark of Microsoft Corporation USA in the United States and other countries.

Sun Microsystems and Java are trademarks or registered trademarks of Sun Microsystems Inc. in the United States and/or other

countries.

1-3 Notes on using AG-150A with the integrated centralized

control software (TG-2000A)

If the system is connected to the integrated centralized control software (referred to as TG-2000A hereafter),

make all settings and changes from the TG-2000A so that the data in TG-2000A and AG-150A will match.

2 Setting the Operating Environment

PC settings and web browser settings required for using a web browser to monitor air conditioner units and

perform operations are explained in the following pages.

2-1 Setting the PC IP Address

Set an IP address on the PC that enables AG-150A to connect via a web browser. For instance, if the

AG-150A IP address is [192.168.1.1], the PC IP address will need to belong to the same system

[192.168.1.101].

If the AG-150A is connected to an existing LAN, ask the LAN administrator to decide what PC IP address to

use.

Note: When using a AG-150A dedicated LAN, it is recommended that the AG-150A main unit be given an IP address

within the range [192.168.1.1] - [192.168.1.40] and the PCs that will be connected to the AG-150A be given an IP

address within the range [192.168.1.101] - [192.168.1.150]

(1) Click on [Control Panel] under [Start] to open the Control Panel.

(2) In the Control Panel window, double click [Network and Dial-up

Connections] and the Network and Dial-up Connections window will

open. Double click on [Local Area Setting] and the [Local Area

Connection Status] dialog will open. Click [Properties].

(3) In the [Local Area Connection Properties] dialog, click [Internet

Protocol] to select it and click the [Properties] button.

(4) In the [Internet Protocol (TCP/IP) Properties] dialog, click [Use the

following IP address] and enter the IP address (for example,

“192.168.1.101”) that you want to set in the IP address field.

You normally set [255.255.255.0] as the subnet mask.

Note: Ask your LAN administrator to provide the IP addresses and subnet mask.

(5) Click the [OK] button to close this dialog, and then close the other open

dialogs to complete the network setting.

2-2 Setting the Web Browser

Necessary web browser settings must be performed to enable the web browser to connect to the AG-150A.

Note: The settings and screen images used as examples in this manual are based on Internet Explorer 6.0.

2-2-1 No Internet Connection

Follow the instructions below to make the web browser environment settings when using the PC with no

Internet connection for monitoring and operating the air conditioners.

(1) Click the web browser menu item [Tools] and then click [Internet

Options…] to select.

(2) In the [Internet Options] tabbed dialog, click the [Connections] tab to

display.

(3) Select [Never dial a connection] in the Dial-up settings section and

click the [OK] button to close the dialog.

2-2-2 Internet Connection Using a Dial-Up

If the PC used for monitoring air conditioners and performing operations is going to connect to the Internet via

a dial-up connection, use the procedure given below to set the web browser environment settings.

By performing these settings, a message will appear asking whether or not to use a dial-up connection when

an Internet connection is necessary. When connecting to the Internet, follow the directions below.

(1) Click the web browser menu item [Tools] and then click [Internet

Options…] to select.

(2) In the [Internet Options] tabbed dialog, click the [Connections] tab to

display.

(3) Select [Dial whenever a network connection is not present] in the

Dial-up settings section and click the [OK] button to close the dialog.

Use a security device such as a VPN router when connecting the AG-150A to the Internet to prevent

unauthorized access.

If no security devices are installed, the operation settings may be changed by an unauthorized person

without the knowledge of the user.

2-2-3 Connecting to the Internet using a proxy server (Using an existing LAN)

If the PC you use for monitoring air conditioners and performing operations is going to access the Internet via

proxy server by connecting to an existing LAN such as a LAN within your company, use the procedure given

below to set the web browser environment settings.

By performing these settings, your PC will connect to a proxy server only when connecting to the Internet.

(1) Click the web browser menu item [Tools] and then click [Internet

Options…] to select.

(2) In the [Internet Options] tabbed dialog, click the [Connections] tab to

display.

(3) Select [Never dial a connection] in the Dial-up setting section.

(4) Click the [LAN Setting . . .] button in the Local Area Network (LAN)

settings section to display the Local Area Network (LAN) Settings

dialog.

(5) In the Local Area Network (LAN) Settings dialog, check [Bypass proxy

server for local addresses] and click the [Advanced...] button.

(6) Enter the IP address for the AG-150A (e.g. 192.168.1.1) in the

Exceptions field of the Proxy Setting dialog and click the [OK] button to

close the dialog and then close the other open dialogs to complete the

setting.

Note: If connecting to more than one AG-150A, you can specify multiple IP

addresses like [192.168.1.1; 192.168.1.2], however, it is also possible to use

the asterisk (*) and specify [192.168.1.*].

2-3 Setting the Java Execution Environment

When using Java Plug-in version 1.6.0_10 or later, make the following environment settings (not required for

version 1.6.0_09 or earlier).

Note: The setting samples and screenshots used in this manual are those of Java Plug-in version 1.6.0_11.

2-3-1 Disabling the next-generation Java Plug-in

(1) Open Java Control Panel by double-clicking Java in the

Control Panel.

(2) In the [Advanced] tab under the [Java Control Panel] screen,

click the plus next to [Java Plug-in] to expand the list, and

uncheck the checkbox next to [Enable the next-generation

Java Plug-in (requires browser restart.)].

3 Performing Operations

Text below explains how to connect to the AG-150A and how to make various settings for the AG-150A.

Note: If the AG-150A is restarted due to a power interruption etc., wait until the screen on the AG-150A main unit displays the

normal operation screen (it takes several minutes before the normal operation screen is displayed) before using a web

browser to access the AG-150A. If access is attempted while the AG-150A is still starting up, the most recent data might

not be displayed or communication errors could occur.

Note: Default IP address of AG-150A is "192.168.1.1". (Factory setting)

3-1 Logging in on the AG-150A

3-1-1 Logging in on the AG-150A

(1) Enter the web page address in the address field of the web

browser as follows:

http:// [IP address of the AG-150A]/g-50

/administrator.html

Press the [Enter] key on the keyboard. A screen appears for login.

Note: For example, type “http://192.168.1.1/g-50/administrator.html” if the

AG-150A IP address is [192.168.1.1].

(2) To make connection easier for the next time, click the web

browser menu item [Favorites], click [Add to Favorites], then add

the address to the Favorites folder. Once this address is added to

the Favorites folder, it is not necessary to input the address of (1).

Simply select it from the Favorites folder and the AG-150A page

will appear.

(3) Enter the user name and the password in the login screen, and click the [Login] button. A screen will

appear in which various setting are made. An explanation on how to perform operations begins from the

next page.

The table below shows the default user names and passwords for maintenance users and building

managers as well as available functions.

User Default

user name Default

password Available functions

Initial settings Date and Time, Basic System, Groups, Interlocked

LOSSNAY, Blocks

Functions 1 E-Mail, Peak cut, Measurement

Functions 2 Set Temperature Range Limit, Night Mode

Schedule, System-changeover

Functions 3 Interlock control based on outside temperature,

Setback control

Interlock control

Maintenance

user initial init

User Settings User Settings

Building

manager administrator admin Out of the functions listed above, the items to which access rights

have been given on the user settings screen are available.

Note: The user name and the password for building manager are the same as those of the building manager of the Web for

monitoring/operation.

Note: Maintenance users can make available to the administrator only the information necessary for normal operations (group

name setting etc.)

Note: It is recommended to change the user name and password so users other than the manager are not permitted to change

the settings.

Note: The Web page is displayed in the same language as the computer uses and it is also possible to display the Web page in

other languages by entering the following Web page addresses.

English :http://[The IP address of AG-150A]/g-50/en/administrator.html

German :http://[The IP address of AG-150A]/g-50/de/administrator.html

French :http://[The IP address of AG-150A]/g-50/fr/administrator.html

Spanish :http://[The IP address of AG-150A]/g-50/es/administrator.html

Italian :http://[The IP address of AG-150A]/g-50/it/administrator.html

Russian :http://[The IP address of AG-150A]/g-50/ru/administrator.html

Chinese :http://[The IP address of AG-150A]/g-50/zh/administrator.html

Portuguese :http://[The IP address of AG-150A]/g-50/pt/administrator.html

Japanese :http://[The IP address of AG-150A]/g-50/ja/administrator.html

3-1-2 Encrypting the communication data and login on the AG-150A

AG-150A can encrypt communication data using HTTPS (SSL).

When connecting the AG-150A to the LAN that can be accessed by the general public, it is recommended

that the following settings be made so that the units are monitored and controlled on the encrypted Web page.

Note: Depending on the operating system or the version of Java, HTTPS encrypted messages may not be handled correctly. If

this happens, use a HTTP connection to monitor and control the units as noted in the section above.

(1) Go to [Tools]->[Internet Options]->[Advanced], and make the

following settings.

Item Checkbox setting

Use SSL 2.0 Uncheck the box.

Use SSL 3.0 Check the box.

Use TLS 1.0 Uncheck the box.

Do not save encrypted pages to disk Check the box.

Note: Some of the settings may have different names depending on the Web

browser version.

(2) Click on [Java] in the Control Panel, and make the settings for the

items under [Security] in the [Advanced] tab.

Item Checkbox setting

Use SSL 2.0 compatible Client Hello format Uncheck the box.

Use SSL 3.0 Check the box.

Use TLS 1.0 Uncheck the box.

Note: Some of the settings may have different names depending on the Java

version.

(3) Prefix the Web address with [https], enter the address, and hit the

[Enter] (Return) key on the keyboard.

https://[IP Address of the AG-150A]/g-50

/administrator.html

Note: For example, type “https://192.168.1.1/g-50/administrator.html” if the

AG-150A IP address is [192.168.1.1].

If the security alert is disabled as described in the note in the

following and the subsequent sections, encrypted date

communication will begin, and the Login screen will appear. If the security alert has not been disabled, take

the following procedures.

(4) If the security alert has not been disabled, after entering the web address and hitting the Enter (Return) key,

a security alert message will alert asking if you want to proceed . This is because the AG-150A uses the

self-authentication system. Click [Yes] and proceed.

Note: Disable the security alert that appears every time the browser is opened, take the following two steps:

1) Register the security certificate and

2) Change the Web browser's option settings

To register the security certificate, click the [View Certificate] button on the security alert window to display the certificate,

click on the [Install Certificate] button, and add the certificate to the Trusted Root Certification Authorities store. Just follow the

prompts of the Import Wizard.

Go to [Tools]->[Internet Options]->[Advanced], and make the following

settings for the Web browser.

Item Checkbox setting

Warn about invalid site certificates Uncheck the box.

(5) A Java security alert message will appear after you click [Yes] in

step (4) above, click [Yes] again to proceed.

Note: To disable the security alert message that appears every time the

browser is opened, check the check box next to [Always trust content

from this publisher], and click [Yes]. The browser may need to be

restarted to reflect the change.

Note: If the window shown on the right does not appear and connection fails,

the certificate needs to be added to the Java certificate list. Click the

[View Certificate] button on the screen in step (4) to display the

certificate, click on the [Copy to File] on the [Details] page, and save the

certificate in any desired location in the DER format. Open [Java] in the Control Panel, click on the [Certificates] button on

the [Security] page to bring up the certificate registration screen. On the screen, select [Secure Site], click on the [Import]

button, change the File of type to [All Files], and select the saved certificate. Now the certificate has been added to the Java

certificate list.

(6) If a connection is successfully made, the login window will appear.

All communication with the AG-150A will be encrypted. The Web

addresses for general users and in each language will have the

web address in the previous section with "http" changed to "https".

4 Initial Settings

This chapter explains how to set the settings on the AG-150A’s initial settings screen.

*Refer to Chapter 5 in the Instruction Book that came with the Centralized Controller AG-150A for how to set the settings after the initial

power on.

4-1 Setting the Current Date and Time

Click [Initial Settings] in the menu, and [Date and Time] screen will appear on the screen. Enter the current

date and time, and then press the [Save Settings] button to send the current date and time to AG-150A.

Note: If the user logs in as a building manager, the operations may be prohibited.

Note: If the system is connected to the TG-2000A, make all settings and changes from the TG-2000A so that the data in

TG-2000A and AG-150A will match.

Note: When the time setting is made on this screen, the setting will be applied to all the units on M-NET system.

Note: The clock setting made on the screen below will be reflected on the clocks on other units that are connected to the M-NET

line, on the Expansion Controllers (PAC-YG50ECA), and on the AG-150A controller whose “Time master setting” is set to

Sub.

Note: When an Expansion Controller (PAC-YG50ECA), DIDO controller (PAC-YG66DCA), AI controller (PAC-YG63MCA), or PI

controller (PAC-YG60MCA) is added to the system, set the clock on the added controller by making the clock setting on the

clock setting screen.

Note: When an Expansion Controller (PAC-YG50ECA), DIDO controller (PAC-YG66DCA), AI Controller (PAC-YG63MCA), or PI

Controller (PAC-YG60MCA) is newly connected, make the time setting of the connected controller on this screen.

Note: When connecting multiple AG-150A controllers by connecting an Expansion Controller to the system, set the “Time master”

according to the instructions in section 4-2-3 "Time Master setting.”

Item Description

Current date/time Enter the current date and time.

For the date, use the format [day - month - year].

Save Settings Click the [Date/Time Set] button to set the current date and time.

Refresh Acquires the current Date and Time from AG-150A.

Summer time setting

Click and tick the "Automatically adjust clock for daylight saving changes" box to

adjust the daylight saving time automatically, and select the applicable country.

Note: If the applicable country is not in the selection bar, select "Custom Settings". Click "Custom

Settings" button that will appear on the right to set the daylight saving time.

Custom Setting Screen

Current date/time

Enter the current date and

time here.

Save settings

Click to set the current date

and time.

Summer time setting

Click to set the daylight saving

time.

Refresh

Acquires the current Date and

Time from AG-150A.

Daylight saving

date and time

Set the daylight

saving time.

CAUTION

Date and clock settings on Expansion Controllers (PAC-YG50ECA), when connected, must be made

with the Expansion Controller properly connected to ensure proper settings.

4-2 Setting the Basic Information and External Input Functions

Display the page needed to perform the AG-150A basic setting by clicking [Initial Settings]-[Basic System] in

the setting menu pane. On this page, you perform the basic setting such as the AG-150A unit name, network

setting and M-NET setting. Click [Save Settings] to send setting data to the AG-150A. After the setting data are

sent to the AG-150A, a message will appear asking whether or not to restart the AG-150A. Click [OK] to restart

the AG-150A to put the changes into effect.

Note: If the user logs in as a building manager, the operations may be prohibited.

4-2-1 AG-150A Unit Setting

In Unit Setting, set the AG-150A name and unit ID.

(1) Enter the AG-150A unit name in the [Name] field. You may enter a maximum of 40 alphanumeric or symbol

characters. The name set here is used on the display screen of the software that controls multiple AG-150A

units and for the name of the sender in the body of error messages.

Note: The following characters cannot be used in the name: < > & " '

(2) Enter the AG-150A unit ID in the [Unit ID] field. You must enter 6 numeric characters. Use this setting when

you want to control multiple AG-150A units with unit IDs. The unit ID that is entered here will be used on the

display screen of the software that controls multiple AG-150A units and for the sender ID in the body of

error messages.

(3) When [Refresh] is clicked, the AG-150A production ID will appear in the [SERIAL No.] field and the

AG-150A software version will appear in the [Software Version] field.

Unit Setting

Set the AG-150A name and

unit ID.

Network Setting

Set the AG-150A IP address

and subnet mask. M-NET Setting

Set the AG-150A M-NET

address, presence/absence of

K-Control units and range of

prohibited controllers.

External Input Setting

Set the AG-150A external

input setting.

Display Format

Set the items related to the

screen display on the AG-150A

or on the Web.

Save Settings

Send setting data to AG-150A.

Refresh

Read setting data from AG-150A.

Use or non-use of expansion

controller

Select from “Do not use” or

“Use.”

System configuration settings

Set the use or non-use of

Expansion Controller, connection

target, M-NET settings, and

external input settings.

Time Master

Select Time Master/Sub

Expansion Controller system

selection buttons

4-2-2 Configuring the System Configuration Settings

In the System Configuration Settings menu, set the use or non-use of PAC-YG50ECA Expansion Controller,

connection target, M-NET settings, and external input settings.

Note: When connecting multiple AG-150A controllers by connecting an Expansion Controller, all controllers must have the same

system configurations.

4-2-2-1 Setting the Expansion Controller Connection Setting

In the M-NET Settings menu, set the use or non-use of PAC-YG50ECA Expansion Controller and connection

target settings.

(1) Select from “Do not use” or “Use” to set the use or non-use of an Expansion Controller.

Note: Before setting the Expansion Controller setting to “Use,” make sure that the Expansion Controller is connected to the LAN.

The settings made without the Expansion Controller being connected may not be saved (M-NET settings, external input

settings, group settings, LOSSNAY interlock settings etc., which are saved on the Expansion Controller side.)

(2) If “Use” is selected for the Expansion Controller setting, an IP

address input field will appear under “Access Point Settings.”

Enter the IP address that is assigned to the Expansion Controller

here.

When connecting two Expansion Controllers, first click [EC1]

and enter the IP address for the first Expansion Controller system, and then click [EC2] to enter the IP

address for the second Expansion Controller system.

Note: Set the IP address for the Expansion Controller itself on the Expansion Controller unit.

(3) After the Expansion Controller connection setting or the IP address of the Expansion Controller was

changed, click the [Save] button and restart the AG-150A by following the messages on the screen. Make

the M-NET settings and external input settings after the system has been restarted.

Note: After connecting the Expansion Controller, check that the database number (DB No.) on the controller itself and the data base

number of the Expansion Controller match. If they do not, consult your dealer for software upgrade.

Note: To change the settings for the external input settings (or any other settings that are saved on the Expansion Controller side)

after the M-NET settings have been made, restart the controller and change the settings with the Expansion Controller

properly being connected to the system.

Note: To change the M-NET settings and external input settings in a system to which an Expansion Controller (PAC-YG50ECA) is

connected, be sure to change the settings with the Expansion Controller properly connected to the system. These settings

are stored on the Expansion Controller.

4-2-2-2 M-NET Setting

In M-NET Setting, set the AG-150A M-NET address, whether or not a K-Control unit is present and which

machines send the prohibited controller command.

(1) Enter the AG-150A M-NET address in the [M-NET Address] field. Normally you should enter [0].

(2) When K-Control air conditioners are connected, click [Used] in the [K-Control Units] field and enter the

M-NET address of K transmission converter in the [K Converter Address] field.

(3) If prohibited controller (prohibiting local operation) has been set, this setting determines the scope of this

setting s control, i.e. operation is prohibited for both the remote control and subordinate system controllers,

or just for the remote control. Click [SC/RC] when you want prohibited controllers to include both

subordinate system controllers and the remote control, or click [RC only] when you only want to prohibit

operation on the remote control.

Note: Normally, you should select [SC/RC].

4-2-2-3 External Input Setting

In the External Input Setting menu, set the AG-150A external input function. By using external input functions,

it is possible to stop and run multiple air conditioners connected to the AG-150A via the separately sold

external I/O adapter for AG-150A (Model: PAC-YG10HA) and external power supply using level signals and

pulse signals.

Note: If PAC-YG50ECA Expansion Controllers are connected, Expansion Controller system selection buttons will appear. Select the

desired Expansion Controller, and make the settings for each system. Make the settings with the Expansion Controllers

properly connected. Connect the external input signal wires to each controller’s external input terminal.

(1) Select [Not in use] when not using the external input function.

(2) Selecting [Emergency stop (Level signal)] makes it possible to stop multiple units by using a level signal.

While this stop operation is being performed, operations such as running or stopping units are prohibited

on the AG-150A unit or remote control.

(3) Selecting [ON/OFF (Level signal)] makes it possible to run or stop multiple units using a level signal. In this mode,

all air conditioner units connected to the AG-150A will be run or stopped and run/stop operations will be prohibited

on the AG-150A unit or remote control.

Contact ON

Contact OFF Normal Emergency

Stop Normal

Contact ON

Contact OFF Stop Run Stop

Run/Stop

Connection to AG-150A (CN5)

DC12V

Emergency stop/normal

Connection to AG-150A

(

CN5

)

DC 12V

(4) Selecting [ON/OFF/Prohibit/Permit (Pulse signal)] makes it possible to use pulse signals to run multiple

units, stop multiple units, prohibit local operation and permit local operation. In this mode, it is possible to

freely operate the remote control except during the pulse signal input.

4-2-3 Time Master Setting

Set the clock on each AG-150A to Master or Sub by selecting either Master or Sub next to “Time Master.”

If an Expansion Controller (PAC-YG50ECA) is used to connect two AG-150A controllers, the unit whose clock

is set to Sub will automatically synchronize its clock to the unit whose clock is set to Master.

Note: Of the AG-150A controllers that are connected to each Expansion Controller (PAC-YG50ECA), the “Time master” setting should

be set to Master on only one AG-150A controller.

Contact ON

Contact OFF

Contact ON

Contact OFF Stop StopRun

0.5 - 1.0 Seconds

Run

Stop

Contact ON

Contact OFF

Contact ON

Contact OFF

Permit Permit

Prohibit

0.5 - 1.0 Seconds

Prohibit

Permit

Connection to AG-150A (CN5) DC12V

Run Stop Prohibit

Permit

:Pulse generator

4-2-4 Network Setting

In Network Setting, set the AG-150A IP address, subnet mask and gateway address. If connecting to the

AG-150A via a permanent LAN, consult with the network administrator before setting these addresses.

4-2-4-1 Settings for when the AG-150A is connected to a dedicated LAN

(1) Enter the AG-150A IP address in the [IP Address] field. If the LAN wiring has been newly set up, allocate IP

addresses to the AG-150A units in a sequential order starting with [192.168.1.1]. For example the first

AG-150A unit will receive an IP address of [192.168.1.1], the second AG-150A unit will receive an IP

address of [192.168.1.2] and so on.

The Web Monitor PC that monitors and sets AG-150A will also require network addresses consistent with

the rest of the LAN.

Note: When using a AG-150A dedicated LAN, it is recommended to set the IP address as follows.

AG-150A: Between [192.168.1.1] and [192.168.1.40] Web Monitor PC: Between [192.168.1.101] and [192.168.1.150]

[Example of IP address setting]

(2) Enter the AG-150A subnet mask in the [Subnet Mask] field. Normally, you should enter [255.255.255.0].

(3) When monitoring remotely or sending error mail via a dial-up router, enter the router IP address in the [Gateway]

field.

Leave the gateway address blank when not connecting via a dial-up router.

[Example of a Remote Monitoring System]

Web Monitor PC AG-150A No. 1 AG-150A No. 2 AG-150A No. 3

Hub

100BASE-TX LAN straight cable

192.168.1.101 192.168.1.1 192.168.1.2 192.168.1.3

AG-150A

IP Address :192.168.1.1

Subnet Mask :255.255.255.0

G/W Address :192.168.1.254

Telecommunication Network

Dial-up router

Dial-up router, cellular phone etc.

Note: Some hubs have a dedicated port for connection with another hub.

Connect the AG-150A and Web Monitor PC to the normal ports.

Note: It is recommended to set the dial-up router IP address to [192.168.1.254]. Refer to the dial-up

router instruction manual for details of how to set the IP address.

Note: It is necessary to connect a modem (analog type or ISDN type) between the dial-up route

and telephone line when using a dial-up router that does not have a built-in modem.

IP: 192.168.1.254

Web Monitor PC Web Monitor PC

IP Address :192.168.1.101

Subnet Mask :255.255.255.0

G/W Address :Blank

4-2-4-2 Settings for when the AG-150A is connected to an existing LAN

When connecting the AG-150A to an existing LAN, consult with the network administrator who is responsible

for the LAN before setting the IP address, subnet mask, or gateway address.

[Example of a Permanent LAN System]

4-2-5 Setting the Display Format

Set the items related to the screen display in the [Display Format] field.

(1) In the [Unit of Temperature] section, select between [ºC] and [ºF] as the unit of temperature.

(2) In the [Date Format] section, select the display order of year/month/day. The date will be displayed in the

selected order on the Web screen or on the mail screen.

Note: Set the format of the date to be displayed on the LCD on the LCD Setting screen.

(3) In the [Time Format] section, select the display of time format. The time will be displayed in the selected

format on the Web screen.

Note: Set the format of the time to be displayed on the LCD on the LCD Setting screen.

(4) In the [Group Names on Overview Monitor] section, select [ON] to display the group name under the icon

on the [Monitor / Operation (Overview)] screen and select [OFF] not to.

Note: Up to 8 letters are displayed under the icon. To display all letters, move the cursor to the icon.

With the display of group names Without the display of group names

Web Monitor PC

AG-150A

Backbone LAN

Web Monitor PC

Gateway Gateway

IP: 10.1.1.250 IP: 10.1.2.250

IP Address :10.1.1.1

Subnet Mask :255.255.255.0

G/W Address :10.1.1.250

IP Address :10.1.1.101

Subnet Mask :255.255.255.0

G/W Address :10.1.1.250

IP Address :10.1.2.51

Subnet Mask :255.255.255.0

G/W Address :10.1.2.250

Receive from the LAN

administrator. Receive from the LAN

administrator.

(5) In the [Filter Sign Display] section, select whether to display the filter sign. Select [ON] to display the filter

sign and [OFF] not to.

When the filter sign display is set to “OFF,” the filter sign on neither the LCD of the AG-150A nor the

monitor screen on the Web browser will appear, even when the indoor unit detects a filter sign.

If the filter is regularly cleaned and the filter sign display is unnecessary, set it to [OFF].

4-3 Group Setting

Display the page needed to register the group of air conditioners or general equipment to be connected to the

AG-150A and to set the group name by clicking [Initial Settings]-[Groups]. On this page, you perform the basic

setting such as the AG-150A unit name, network setting and M-NET setting. Click [Set to AG-150A] to send

setting data to the AG-150A.

Note: If PAC-YG50ECA Expansion Controllers are connected, Expansion Controller system selection buttons will appear. Select

the desired Expansion Controller (EC1, EC2, or EC3), and make the settings for each system.

Note: If the user logs in as a building manager, some of the operations may be prohibited.

Note: If the system is connected to the TG-2000A, make all settings and changes from the TG-2000A so that the data in

TG-2000A and AG-150A will match.

Note: A contact on the genera interface device is regarded as one unit. The number of units that can be connected to AG-150A is

up to 50.

Note: Air-conditioners and general equipment cannot be in the same group.

Note: Remote controllers or system controllers cannot be connected to general equipment.

Note: When connecting multiple AG-150A controllers by connecting an Expansion Controller, all controllers must have the same

control group settings.

4-3-1 Setting the Group Name

(1) In the [Group Name for Web] field on the screen, register the group name to be displayed on the Web

screen, using a name consisting of no more than 20 characters.

Note: The following characters cannot be used in the group name: < > & " '

(2) Next, in the [Group name for LCD of the AG-150A] field, enter the group name to be displayed on the LCD

of the AG-150A consisting of no more than 10 numbers, upper case letters, hyphen, or space combined.

4-3-2 Registering air conditioner or hot water supply units in the group

(1) To register air-conditioners, clicking the [Air Conditioner or

general equipment or hot water supply Registration] field next to

each group in the [Groups] screen will bring up the [Select Unit

Addresses] screen. Click on the numbers corresponding to the

units to be registered. All selected units will be shown with a

yellow-green background.

To cancel the selection, click on them again. Deselected items will

be shown with a gray background.

Note: A maximum of 16 air conditioner units can be registered in one group.

Note: To change the registered units to air-conditioners in the group in which

general equipment is registered, disconnect the general equipment first.

(2) To change the icon, click the right or left arrow.

Group No.

Group numbers will be

displayed here.

Remote Controller

Registration

to be connected here. Click to

bring up the registration screen.

Air Conditioner or general

equipment or hot water

supply Registration

general equipment or hot

water supply to be connected

here. Click to bring up the

registration screen.

System Controller

Registration

to be connected here. Click to

bring up the registration screen.

Group name

The group names are entered

here.

Save Settings

Send setting data to AG-150A.

Refresh

Read setting data from AG-150A.

Expansion Controller

system selection buttons

Click to select the system to

be set.

CAUTION

Control group settings on Expansion Controllers (PAC-YG50ECA), when connected, must be made

with the Expansion Controller properly connected to ensure proper settings.

Page is loading ...

Mitsubishi AG-150A User manual

Brand: Mitsubishi

Model: AG-150A

Category: Split-system air conditioners

Type: User manual

This manual is also suitable for

Download PDF

report

Mitsubishi AG-150A User manual

This manual is also suitable for

Mitsubishi AG-150A User manual

Related papers

Other documents