AUTOOL X60 OBD2/OBDII Digital Compteur de Vitesse de Voiture User manual

Type
User manual
AUTOOL X60 Car OBD Multi-Function Meter
User Manual
Product Introduction
Supported Vehicle
For petrol vehicle with standard OBD-II protocol, especially for vehicle
without water gauge, speedometer and fuel consumption meter.
Installation
X60 is a OBD multi-function meter, with smart and fashion design. It is
easy to install. OBD port helps you use it once connection. No need to
destroy the wire.
Hardware
CPU based on 32 bit ARM CORTEX-M3 kernel; Maximum operating
frequency: 72MHz; Support multiple high speed auto communication
protocols.
Warning Function:
Supporting water temperature warning, over-speed alarm, shifting
reminding, vehicle malfunction warning, which secure safe driving.
Trouble code clearing:
Support code scanning and general code clearing.
Product Parameter
Operating voltage: 10-18V DC Operating current: <80mA
Sleep current: <15mA Operating Temperature: -20~75℃
Volume: 60mm×50mm×67mm
Product packing list: host, OBD cable, 3M double-sided tape, user
manual, certificate.
Product Description
X60 OBD computer is a smart and powerful auto meter. It is
especially designed for vehicle without speedometer, engine
- 2 -
temperature gauge, oil thermometer, boost gauge and fuel
consumption meter.
X60 can also monitor and display battery voltage, engine charging
voltage, overspeed alarm, engine temperature warning. It can even read
the real-time data stream, scan and clear trouble code.
Product Appearance
1. Function button
2. OBD port
3. Ambient light detector
4. Display
Turn right/left of function button to quick select from main screen. In setting
mode, turn right/left to choose menu. Press down in the middle to confirm. Long
press M in the middle to exit or back.
Holder Installation
- 3 -
1. Tear 3M doble-sided tape, and fasten it with holder base.
2. Pull up the bottom center to right and left.
3. Insert the base of holder to the bottom of host.
4. Insert the bolt from right, and nut from left.
5. Fasten the screw with screwdriver.
- 4 -
Product Installation and Operation
Connect one side of OBD cable with car OBD port, the other side with X60
OBD port.
After connection with host, start the car and wait X60 to connect with vehicle.
Connecting successfully, the host ticks, and X60 displays vehicle protocol. Then, it
will show parameter setting for the first use.
Definition of International General OBD Socket Protocol Defined by SAE
Connection port for X60 and vehicle
Tips for Product Installation:
Make sure the dashboard is clean before installation. If the dashboard is
waxed, the tape cannot paste, so please tidy with hot towel, then, install the product. It
will be the best if heating it up with dryer during installation.
Product Operating Setting
Turn right/left of button in the top of host, the displayed large
character can be switched fast.
- 5 -
If the product doesnot support currenct data display, red X will be
displayed. If funtion data needed cannot be selected, please check in the
data stream of Electronic Control Diagnosis System.
SPEED current speed SPEED AVG average speed
WATER T. water temperature INTAKE T. intake temperate
OUTSIDE T. outside temperature VOLTAGE battery voltage
FUEL P. fuel pressure MAP manifold absolute pressure
ENG LOAD engine load TAHCO/RPM revolutions per minute
FUEL LEVEL fuel level DISTANCE distance
FUEL C;AVG fuel average FUEL C fuel consumption
OTL P. engine oil pressure OIL T. engine oil temperature
INGITION T. INGITION Turbine CLOCK time
THROTTLE P. throttle position
Electronic Control Diagnosis System
Press the function button to Electronic Control Diagnosis System. It
includes 3 functions. See the picture below:
- 6 -
Choose the function“Scan DTCs”, it can read trouble code, and
you can decide if clearing the code.
Choose “Data Stream”. It will monitor real-time data. Turn
right/left of the button, it will show page up and down.
Vehicle Performance Test
Vehicle performance test includes: speedup test, brake test, target
speedup, brake initial speed
- 7 -
Before speedup test, please set target speedup. When it reaches to
the scheduled speed, finish speedup test.
Before brake test, please set brake initial speed. When it reaches to
brake initial speed, calculate the distance from beginning to the end of
acceleration.
Product Parameter Setting
In parameter setting, turn right/left of the button to set the
parameter value. Long press function key back to previous menu.
Product Parameter Setting Including:
1. Engine displacement - To accurately calcuate instant and average
fuel consumption
- 8 -
2. Fuel type - Choose petrol or other type fuel, fuel consumption
data will be much different.
3. Overspeed alarm - When it reaches to the scheduled speed, it will
tick to alarm, and the character for speed will display in red.
4. Water temperature warning - When it reaches to the schechuled
engine temperature, it will tick to alarm, and the character for
temperature will display in red.
5. Shift reminding - When it reaches to the scheduled speed, it will
remind to shift, and display shift symbol.
6. Shift reminding limit - When it reaches to the scheduled speed, it
will turn off shift reminding, in case it exceeds the scheduled speed, and
cannot shift up.
7. Standby time - After the vehicle shuts down, and it reaches to the
scheduled standby time, X60 will change to automatic sleep.
8. Speed error adjustment - when the speed is 100km, adjust
displayed speed of X60 to 100km.
9. Battery voltage adjustment - Adjust X60 voltage to display
accurately.
10. Voltage warning - To remind the driver if the battery is under
charge
11. Color of number - 7 colors to choose.
12. Speed to zero - In idle speed mode, speed will display zero if it is
lower than the scheduled.
13. Fuel consumption adjustment - Average fuel consumption is
less the actual. If it displays more, adjust the percentage to be smaller,
and vice versa.
14. Reset - X60 will revert to the initial state.
- 9 -
X60 Display Setting
To set display in X60
In working condition, 4 types of information will display. They
corresponds to the following content:
1 - Quick switch to displayed quantity and content
2,3 - Set more content
4 - Set to display instant fuel consumption or RPM bar
The 10 round icons in the top are shift reminding display. It is default off.
- 10 -
Product Information
It helps to check software version, vehicle protocol and solution for
protocol compatibility.
About protocol compatibility
When connecting with some vehicles, gauge LED or touble alarm LED
may be lit. Please follow the “Matching inf to operate - Please open
OBD cable of product, and cut off the corresponding pins to solve the
problem.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

AUTOOL X60 OBD2/OBDII Digital Compteur de Vitesse de Voiture User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI