American Standard 8193.140 User manual

Type
User manual

This manual is also suitable for

American Standard 8193.140 is an undercabinet storage rack designed to provide additional storage space in your kitchen. It is made of durable materials and is easy to install. The rack can be positioned to the left or right under the sink, and it comes with all the necessary hardware for installation. The top of the rack is sloped, so that when it is correctly installed, the bottom of the rack will be parallel with the rim of the sink. This makes it easy to access the items stored on the rack, even when the sink is full.

American Standard 8193.140 is an undercabinet storage rack designed to provide additional storage space in your kitchen. It is made of durable materials and is easy to install. The rack can be positioned to the left or right under the sink, and it comes with all the necessary hardware for installation. The top of the rack is sloped, so that when it is correctly installed, the bottom of the rack will be parallel with the rim of the sink. This makes it easy to access the items stored on the rack, even when the sink is full.

LAKELAND™ UNDERCABINET STORAGE RACK
8193.140
Installation
Instructions
791407-100
BEFORE YOU BEGIN:
IMPORTANT: DIMENSION OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN PERMITTED MANUFACTURING TOLERANCES.
©AMERICAN STANDARD INC. 2005
• Carefully unpack your accessory, check the contents, and inspect carefully for damage.
RECOMMENDED TOOLS & MATERIALS:
• Locate the fixing screw holes on the underside of the sink.
• Make sure the threads are clear and mark around them. Fig 1.
• Regular Screwdriver (Small)
• Phillips Screwdriver
• Flash Light
• Pliers
• Tape Measure
• Masking Tape or Yellow Crayon
Mounting Kit Consists Of:
• Put two clips on each of the top thick wires.
• Gently squeeze them closed.
• The exact location of the clips may vary depending on whether you want to position your storage rack
to the left or right. Fig 2 & 3.
Note: The top of the rack is manufactured with a slope. When it is correctly installed under the sink the bottom
of the rack will be parallel with the rim of the sink.
Thank you for selecting American-Standard...the benchmark of fine quality
for over 100 years. To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
• 4 Clips
• 2 Long and 2 Short Metric Machine Screws
• 10 Flat and 4 Anti-shake (star) washers. Fig 4.
2
1
Fig.1
Fixing Screw
Hole Locations
Fig.2
Fig.3
791407-100
©AMERICAN STANDARD INC. 2005
Place one anti-shake and then one flat washer on two long and two short screws. (Extra included in pack.)
Position the rack under the sink and secure in place with the screws. Fig.5
Gently tighten the screws.DO NOT OVER TIGHTEN THE SCREWS AS THIS MAY BREAK THE WELD NUT
If a clip is not tight on the wire, remove the screw and add more flat washers until the clip grips the wire. Fig.7.
5
3
4
Long Screws
Long Screws
Short Screws
Short Screws
Flat Washers
Clips
Anti-shake Washer
Fixing Screw
Hole Locations
Fig.5
Fig.4
Fig.6
Fig.7
Note: The long screws go to the right hand side (outer edge) and the short screws go to the left hand side (center)
when looking from the front. Fig.6
  • Page 1 1
  • Page 2 2

American Standard 8193.140 User manual

Type
User manual
This manual is also suitable for

American Standard 8193.140 is an undercabinet storage rack designed to provide additional storage space in your kitchen. It is made of durable materials and is easy to install. The rack can be positioned to the left or right under the sink, and it comes with all the necessary hardware for installation. The top of the rack is sloped, so that when it is correctly installed, the bottom of the rack will be parallel with the rim of the sink. This makes it easy to access the items stored on the rack, even when the sink is full.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI