TECHNICAL DATA
MAR-04
MARINE COATINGS
PRIMER FOR METAL
Form: GDH-161
Rev.: 090413
1
].DESCRIPTION AND USES .
Rust-Oleum
®
Marine Coatings Primer For Metal is
designed to prime metals above the waterline before
application of Marine Coatings Topside Paint. It has
excellent adhesion which prevents chipping, cracking and
peeling and eliminates the need for additional topcoats
and touch-ups. Use on bare, painted or lightly rusted
metals. NOT FOR USE BELOW THE WATERLINE OR
ON GALVANIZED SURFACES.
.PRODUCTS .
SKU Description
207016 Primer (1-Quart)
.PRODUCT APPLICATION .
SURFACE PREPARATION
All surfaces must be free of dirt, loose paint, oil, grease,
wax, soap and any other foreign matter. Clean previously
coated surfaces by washing with a solution of 2 cups
household ammonia per gallon of water and rinse well.
Remove existing mildew with household bleach. DO NOT
MIX AMMONIA AND BLEACH TOGETHER. Rinse
thoroughly and allow to dry.
PREVIOUSLY PAINTED – Old paint is in good, sound
condition should be washed thoroughly with mineral spirits
or xylene. Sand smooth with 80 grit sandpaper and
solvent wipe with mineral spirits or a tack rag to remove
residue. Apply a coat of Marine Coatings Primer For Metal.
If the old paint is in poor condition, remove it with a paint
and varnish remover or by sanding.
ALUMINUM – Lightly sand the surface smooth with #150
grit sandpaper to remove oxidation. Wipe the surface with
mineral spirits or xylene to remove sanding dust and
residue. Make repairs to the surface as necessary. Apply
a coat of Marine Coatings Primer For Metal and allow to
dry 24 hours before application of Marine Coatings
Topside Paint.
STEEL – Abrasive blast to bare metal or abrade with
emery cloth or a wire wheel. Make repairs to the surface
as necessary. Wipe the surface with mineral spirits or
xylene to remove sanding dust and residue. Immediately
apply a coat of Marine Coatings Primer For Metal and
allow to dry for 24 hours before application of Marine
Coatings Topside Paint.
PRODUCT APPLICATION (cont.) .
APPLICATION
Apply when air (ambient) temperature is between 50-90°F
(10-32°C) and the relative humidity is below 85%. Do not
apply on extremely humid days (90% humidity or above)
or when rain is threatening. Do not apply in the late
afternoon outdoors as the wet film may be adversely
affected by dew. When working in cooler temperatures, be
sure the air and surface temperatures will remain at or
above 50°F for at least 4 hours after application.
Mix thoroughly to ensure any settled pigment is re-
dispersed before use. Apply with a high quality brush,
roller, conventional or airless spray. For brush or roller
application, apply full strength. In hot weather, thin with
5% mineral spirits to maintain a wet edge. On large,
smooth surfaces, apply using a short nap or foam roller
cover followed immediately by back brushing. If using
conventional spray application, thin 5% with xylene and
apply one thin, even coat. After four hours, lightly sand
with 150 grit sandpaper and apply a second coat. Always
wipe with a tack cloth immediately after sanding to remove
any airborne dust that may have settled on the surface. If
using airless spray, apply using 1,600-2,400 psi with a
0.013-0.017 inch tip. If necessary, thin up to 5% with
xylene.
DRY & RECOAT
Dry and recoat times are based on 70°F and 50% relative
humidity. Allow more time at cooler temperatures. Dries to
the touch in 1-2 hours, to handle in 4-6 hours, and can be
recoated after 24 hours.
CLEAN-UP
Clean up application tools and equipment with mineral
spirits.
TECHNICAL DATA
MARINE COATINGS PRIMER FOR METAL
Rust-Oleum Corporation Form: GDH-161
11 Hawthorn Parkway Phone: 877•385•8155 Rev.: 090413
Vernon Hills, Illinois 60061 www.rustoleum.com
An RPM Company
PHYSL t
PRIMER FOR METAL
Resin Type
Modified Alkyd
Pigment Type
Titanium Dioxide and Fillers
Solvents
Aromatic Hydrocarbons
Weight
Per Gallon
10.3 lbs.
Per Liter
1.23 kg
Solids
By Weight
62.7%
By Volume
39.8%
Volatile Organic Compounds
464 g/l
Recommended Dry Film
Thickness (DFT) Per Coat
1.0-1.5 mils
Wet Film to Achieve DFT
(unthinned material)
2.5-4.0 mils
Theoretical Coverage at
1 mil DFT (25µ) sq.ft./gal
160 sq.ft./quart
Practical Coverage at Recommended DFT
(sq.ft./gal) (assumes 15% material loss)
100 ft
2
/quart
Dry Times at
70°F (21°C)
and 50%
Relative
Humidity
Touch
1-2 hours
Handle
4-6 hours
Recoat
24 hours
Shelf Life
3 years
Flash Point
104°F (40°C)
Safety Information
For additional information, see MSDS
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The
statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use
of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any,
will be limited to replacement of defective materials. All technical information is subject to change without notice.
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Quick Color J2855830 User manual
-
Rust-Oleum 206999 User manual
-
Rust-Oleum Automotive 251580 User guide
-
Rust-Oleum Stops Rust 238316 User manual
-
Rust-Oleum Stops Rust 7777502 User manual
-
Zinsser 2001 User manual
-
Lanco MM300-4 User manual
-
Rust-Oleum Automotive 253499 User manual
-
Rust-Oleum Stops Rust 8781502 User manual
-
Rust-Oleum Automotive 253351 User guide
