Clatronic HSMR 2592 Owner's manual

Page is loading ...

General safety instructions

• Before commissioning this device please read the instruction manual

carefully.

• Please keep these instructions, the guaranty certificate, the sales receipt and, if

possible, the carton with the inner packaging!

• The device is intended exclusively for private and not for commercial use!

• Always remove the plug from the socket whenever the device is not in use, when

attaching accessory parts, cleaning the device or whenever a disturbance

occurs. Switch off the device beforehand. Pull on the plug, not on the cable.

• In order to protect children from the dangers of electrical appliances, never leave

them unsupervised with the device. Consequently, when selecting the location

for your device, do so in such a way that children do not have access to the devi-

ce. Take care to ensure that the cable does not hang down.

• Test the device and the cable regularly for damage. If there is damage of any

kind, the device should not be used.

• Do not repair the device yourself, but rather consult an authorised expert.

• For safety reasons a broken or damaged mains lead may only be replaced by an

equivalent lead from the manufacturer, our customer service department or a

similary qualified person.

• Keep the device and the cable away from heat, direct sunlight, moisture, sharp

edges and suchlike.

• Never use the device unsupervised! Switch off the device whenever you are not

using it, even if this is only for a moment.

• Use only original accessories.

• Do not use the device outdoors*).

• Under no circumstances must the device be placed in water or other liquid, or

come into contact with such*). Do not use the device with wet or moist hands*).

• Should the device become moist or wet, remove the mains plug from the socket

immediately*). Do not reach into the water.

• Use the device only for the intended purpose.

*) Please note the following „Special safety instructions...“.

Special safety instructions for this device

• Use this machine to cut dry hair only.

• Use this machine to cut only hair and beards.

• Do not charge the machine in a humid atmosphere.

• When charging keep the machine AWAY from direct sunlight or sources of heat.

• Do not press the cutting head too much against the skin. Danger of injury!

• NEVER use any adapter other than that supplied with the machine.

29

GB

40986-05-HSM-R 2592 29.08.2002 12:46 Uhr Seite 29

Use

Components

1. Cutting head 5. Connection socket

2. ON selector 6. Adapter (charger)

3. Cutting length comb: 7. Charging station/mounting

4, 6, 8, 10, 12, 14, 16 mm 8. Locking switch

4. Charging LED (Lock/Unlock)

Accessories: 1. Comb

2. Cleaning brush

3. Special oil

Direct connection mode and battery mode

The hair and beard cutting machine can be used either in direct connection mode

with the adapter or in battery mode after being charged. For DIRECT CONNEC-

TION MODE insert the plug of the adapter into a 230V/50Hz socket, insert the

connection cable into the connection socket located on the hair clipper and place

the function selector either on ON. The machine is pre-charged ex works. Please

charge up the device for 12 hours before initial use. The maximum length of the

subsequent charge cycles is approximately 8 hours. When fully charged the device

has a maximum operating life of 25 minutes. After this time it must be switched off

and allowed to cool down for 25 minutes. The charging LED lights up during the

charging procedure.

Useful tips on battery life

Battery life can be lengthened by paying attention to the following instructions:

• Wait until the battery is almost completely flat before charging it.

• Never leave the machine connected to the charger for more than 24 hours.

• Charge the machine only with room temperatures between 0 and +40°C.

Beard trimming and cutting

• Shift the selector (2) to the ON position. Start with the longest cutting level and

shorten the whole beard or the beard on the chin or cheeks gradually to the

desired length.

Note: Lock the selected cutting length (cutting length comb) in position with the

locking switch located on the back of the housing (position 8 – „lock“).

Hair cutting/thinning

• Shift the selector (2) to the ON position. Start with the longest cutting level and

shorten the hair gradually to the desired length.

Note: Lock the selected cutting length (cutting length comb) in position with the

locking switch located on the back of the housing (position 8 – „lock“).

30

GB

40986-05-HSM-R 2592 29.08.2002 12:46 Uhr Seite 30

Contour cutting and neck shaving

•

Remove the cutting length comb (3) and shift the selector (2) to the

ON

position.

• The shearing head enables the precise trimming of the beard contours even

areas, which are difficult to reach, and the clean shaving of the hairline in the

neck area.

Maintenance and care

The regular cleaning and maintenance of the machine will guarantee optimal

results and long machine life.

• Use only a slightly humid and soft cloth to clean the machine.

• After using each time remove all the hair left on the machine with cleaning

brush.

• Remove the cutting length comb and the cutting head to either blow away the

hair particles or brush them away with the cleaning brush.

• After using the machine each time apply 1-2 drops of acid-free oil (sewing

machine oil) on the cutting head.

Attention:

It is not allowed to recharge the battery continuesly more than 48 hours.

This appliance conforms with the CE directives for radio interference suppression

and low-voltage safety and has been built to meet current safety requirements.

Subject to technical changes without prior notice!

Warranty

We undertake to guarantee the appliance sold by our company for 24 months as of

the date of purchase (cash receipt).

During the life of the warranty we shall provide for the repair or replacement of the

appliance owing to material or manufacturing defects absolutely free of charge.

Proof for the warranty is provided by the purchase document. The replacement and

repair will not be performed free of charge without this proof of purchase.

Should the warranty be valid, please consign the complete appliance in its original

packing together with the cash receipt to your local dealer.

You are not entitled to the replacement of the appliance owing to broken glass parts

and faulty accessories. However, said parts will be replaced free of charge. In this

case only the faulty accessory needs to be ordered without sending back the whole

appliance!

The cleaning, servicing and replacement of wear parts are not covered by this war-

ranty and hence are to be paid for.

The warranty is terminated in case of handling on the part of Third parties.

31

GB

40986-05-HSM-R 2592 29.08.2002 12:46 Uhr Seite 31

After the warranty

Once the warranty has expired, repairs can be carried out by specialized technici-

ans or repair services against the payment of the service.

32

GB

40986-05-HSM-R 2592 29.08.2002 12:46 Uhr Seite 32

Page is loading ...

D-47906 Kempen/Germany · Industriering Ost 40

Internet: http://www.clatronic.de · email: [email protected]

Stünings, Krefeld • 12/00

Technische Daten

Modell: HSM-R 2592

Ladezeit Akkus: 8 Stunden

Spannungsversorgung Netzadapter: 230 V ~, 50 Hz

Ausgang Netzadapter: 4,5 V/1000 mA/4 W

Schutzklasse:

ΙΙ

KB: 25 min.

Dieses Gerät entspricht den CE-Richtlinien.

Bitte führen Sie das ausgediente Gerät

einer umweltgerechten Entsorgung zu.

NiCd:

40986-05-HSM-R 2592 29.08.2002 12:46 Uhr Seite 49

Clatronic HSMR 2592 Owner's manual

Clatronic HSMR 2592 Owner's manual

in other languages

Related papers

Other documents