Hobart H200L4-15 GUN User manual

Brand: Hobart

Model: H200L4-15 GUN

Category: Welding System

Type: User manual

This manual is also suitable for

IronMan 230

And H200L4-15 Gun

Processes

OM-235 281A 2009−07

Gas Metal Arc (MIG) Welding

Flux Cored Arc (FCAW)

Welding

Description

Arc Welding Power Source and Wire

Feeder

™

File: MIG (GMAW)

Hobart Welders manufactures a full line

of welders and welding related equipment.

For information on other quality Hobart products, contact your local Hobart

distributor to receive the latest full line catalog or individual specification sheets.

To locate your nearest distributor or service agency call 1-877-Hobart1 or

visit our website at www.HobartWelders.com.

For Technical Help call 1-800-332-3281.

Thank you and congratulations on choosing Hobart. Now you can get the

job done and get it done right. We know you don’t have time to do it any

other way.

This Owner’s Manual is designed to help you get the most out of your

Hobart products. Please take time to read the Safety precautions. They

will help you protect yourself against potential hazards on the worksite.

We’ve made installation and operation quick

and easy. With Hobart you can count on years

of reliable service with proper maintenance.

And if for some reason the unit needs repair,

there’s a Troubleshooting section that will help

you figure out what the problem is. The parts

list will then help you to decide the exact part

you may need to fix the problem. Warranty and

service information for your particular model

are also provided.

Hobart is registered to the

ISO 9001:2000 Quality

System Standard.

Working as hard as you

do − every power source

from Hobart is backed by

the best warranty in the

business.

From Hobart to You

Hob_Thank 4/05

HobartWelders.com

Protect Your Investment!

TABLE OF CONTENTS

SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1. Symbol Usage 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2. Arc Welding Hazards 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-3. Additional Symbols For Installation, Operation, And Maintenance 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-4. California Proposition 65 Warnings 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-5. Principal Safety Standards 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-6. EMF Information 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION 5. . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-1. Symboles utilisés 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-2. Dangers relatifs au soudage à l’arc 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance 7. . . . . .

2-4. Proposition californienne 65 Avertissements 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-5. Principales normes de sécurité 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-6. Information EMF 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 3 − INTRODUCTION 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-1. Specifications 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-2. Welding Power Source Duty Cycle And Overheating 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-3. Volt-Ampere Curves 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-4. Installing Welding Gun 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-5. Connecting To Weld Output Terminals 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-6. Installing Work Clamp 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-7. Setting Gun Polarity For Wire Type 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-8. Installing 2 lb Wire Spool And Adjusting Hub Tension 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-9. Installing 10 lb Wire Spool And Adjusting Hub Tension 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-10. Installing 33 lb Wire Spool And Adjusting Hub Tension 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-11. Installing Gas Supply 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-12. Positioning Jumper Links 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-13. Electrical Service Guide 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-14. Selecting A Location And Connecting Input Power 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-15. Threading Welding Wire 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-16. Installing Optional DP 3545 Spool Gun To Welding Power Source 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 4 − OPERATION 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-1. Controls 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-2. Weld Parameters 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 5 − MAINTENANCE AND TROUBLESHOOTING 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-1. Routine Maintenance 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-2. Supplementary Protectors 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-3. Replacing Drive Roll And Wire Inlet Guide 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-4. Removing Knob From Front Panel 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-5. Aligning Drive Rolls and Wire Guide 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-6. Replacing Gun Contact Tip 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-7. Installing Cable Hangers 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-8. Removing Nozzle, Contact Tip, And Adapter, Changing Liner, And Cleaning Gun Casing 29. . . . . . . . .

5-9. Welding Troubleshooting Table 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-10. Wire Drive/Gun Troubleshooting Table 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TABLE OF CONTENTS

SECTION 6 − MIG WELDING (GMAW) GUIDELINES 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-1. Typical MIG Process Connections 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-2. Typical MIG Process Control Settings 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-3. Holding And Positioning Welding Gun 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-4. Conditions That Affect Weld Bead Shape 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-5. Gun Movement During Welding 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-6. Poor Weld Bead Characteristics 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-7. Good Weld Bead Characteristics 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-8. Troubleshooting − Excessive Spatter 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-9. Troubleshooting − Porosity 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-10. Troubleshooting − Excessive Penetration 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-11. Troubleshooting − Lack Of Penetration 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-12. Troubleshooting − Incomplete Fusion 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-13. Troubleshooting − Burn-Through 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-14. Troubleshooting − Waviness Of Bead 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-15. Troubleshooting − Distortion 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-16. Common MIG Shielding Gases 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-17. Troubleshooting Guide For Semiautomatic Welding Equipment 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 7 − ELECTRICAL DIAGRAM 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 8 − PARTS LIST 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

WARRANTY

OM-235 281 Page 1

SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING

som _2009−07

Protect yourself and others from injury — read and follow these precautions.

1-1. Symbol Usage

DANGER! − Indicates a hazardous situation which, if

not avoided, will result in death or serious injury. The

possible hazards are shown in the adjoining symbols

or explained in the text.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury. The possible

hazards are shown in the adjoining symbols or ex-

plained in the text.

NOTICE − Indicates statements not related to personal injury.

. Indicates special instructions.

This group of symbols means Warning! Watch Out! ELECTRIC

SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult sym-

bols and related instructions below for necessary actions to avoid the

hazards.

1-2. Arc Welding Hazards

The symbols shown below are used throughout this manual

to call attention to and identify possible hazards. When you

see the symbol, watch out, and follow the related instructions

to avoid the hazard. The safety information given below is

only a summary of the more complete safety information

found in the Safety Standards listed in Section 1-5. Read and

follow all Safety Standards.

Only qualified persons should install, operate, maintain, and

repair this unit.

During operation, keep everybody, especially children, away.

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal shocks

or severe burns. The electrode and work circuit is

electrically live whenever the output is on. The input

power circuit and machine internal circuits are also

live when power is on. In semiautomatic or automatic

wire welding, the wire, wire reel, drive roll housing,

and all metal parts touching the welding wire are

electrically live. Incorrectly installed or improperly

grounded equipment is a hazard.

D Do not touch live electrical parts.

D Wear dry, hole-free insulating gloves and body protection.

D Insulate yourself from work and ground using dry insulating mats

or covers big enough to prevent any physical contact with the work

or ground.

D Do not use AC output in damp areas, if movement is confined, or if

there is a danger of falling.

D Use AC output ONLY if required for the welding process.

D If AC output is required, use remote output control if present on

unit.

D Additional safety precautions are required when any of the follow-

ing electrically hazardous conditions are present: in damp

locations or while wearing wet clothing; on metal structures such

as floors, gratings, or scaffolds; when in cramped positions such

as sitting, kneeling, or lying; or when there is a high risk of unavoid-

able or accidental contact with the workpiece or ground. For these

conditions, use the following equipment in order presented: 1) a

semiautomatic DC constant voltage (wire) welder, 2) a DC manual

(stick) welder, or 3) an AC welder with reduced open-circuit volt-

age. In most situations, use of a DC, constant voltage wire welder

is recommended. And, do not work alone!

D Disconnect input power or stop engine before installing or

servicing this equipment. Lockout/tagout input power according to

OSHA 29 CFR 1910.147 (see Safety Standards).

D Properly install and ground this equipment according to its

Owner’s Manual and national, state, and local codes.

D Always verify the supply ground − check and be sure that input

power cord ground wire is properly connected to ground terminal in

disconnect box or that cord plug is connected to a properly

grounded receptacle outlet.

D When making input connections, attach proper grounding conduc-

tor first − double-check connections.

D Keep cords dry, free of oil and grease, and protected from hot metal

and sparks.

D Frequently inspect input power cord for damage or bare wiring −

replace cord immediately if damaged − bare wiring can kill.

D Turn off all equipment when not in use.

D Do not use worn, damaged, undersized, or poorly spliced cables.

D Do not drape cables over your body.

D If earth grounding of the workpiece is required, ground it directly

with a separate cable.

D Do not touch electrode if you are in contact with the work, ground,

or another electrode from a different machine.

D Do not touch electrode holders connected to two welding ma-

chines at the same time since double open-circuit voltage will be

present.

D Use only well-maintained equipment. Repair or replace damaged

parts at once. Maintain unit according to manual.

D Wear a safety harness if working above floor level.

D Keep all panels and covers securely in place.

D Clamp work cable with good metal-to-metal contact to workpiece

or worktable as near the weld as practical.

D Insulate work clamp when not connected to workpiece to prevent

contact with any metal object.

D Do not connect more than one electrode or work cable to any

single weld output terminal.

SIGNIFICANT DC VOLTAGE exists in inverter weld-

ing power sources AFTER removal of inputpower.

D Turn Off inverter, disconnect input power, and discharge input

capacitors according to instructions in Maintenance Section

before touching any parts.

HOT PARTS can burn.

D Do not touch hot parts bare handed.

D Allow cooling period before working on equip-

ment.

D To handle hot parts, use proper tools and/or

wear heavy, insulated welding gloves and

clothing to prevent burns.

OM-235 281 Page 2

Welding produces fumes and gases. Breathing

these fumes and gases can be hazardous to your

health.

FUMES AND GASES can be hazardous.

D Keep your head out of the fumes. Do not breathe the fumes.

D If inside, ventilate the area and/or use local forced ventilation at the

arc to remove welding fumes and gases.

D If ventilation is poor, wear an approved air-supplied respirator.

D Read and understand the Material Safety Data Sheets (MSDSs)

and the manufacturer’s instructions for metals, consumables,

coatings, cleaners, and degreasers.

D Work in a confined space only if it is well ventilated, or while

wearing an air-supplied respirator. Always have a trained watch-

person nearby. Welding fumes and gases can displace air and

lower the oxygen level causing injury or death. Be sure the breath-

ing air is safe.

D Do not weld in locations near degreasing, cleaning, or spraying op-

erations. The heat and rays of the arc can react with vapors to form

highly toxic and irritating gases.

D Do not weld on coated metals, such as galvanized, lead, or

cadmium plated steel, unless the coating is removed from the weld

area, the area is well ventilated, and while wearing an air-supplied

respirator. The coatings and any metals containing these elements

can give off toxic fumes if welded.

Arc rays from the welding process produce intense

visible and invisible (ultraviolet and infrared) rays

that can burn eyes and skin. Sparks fly off from the

weld.

D Wear an approved welding helmet fitted with a proper shade of

filter lenses to protect your face and eyes from arc rays and

sparks when welding or watching (see ANSI Z49.1 and Z87.1

listed in Safety Standards).

D Wear approved safety glasses with side shields under your

helmet.

D Use protective screens or barriers to protect others from flash,

glare and sparks; warn others not to watch the arc.

D Wear protective clothing made from durable, flame-resistant

material (leather, heavy cotton, or wool) and foot protection.

ARC RAYS can burn eyes and skin.

Welding on closed containers, such as tanks,

drums, or pipes, can cause them to blow up. Sparks

can fly off from the welding arc. The flying sparks, hot

workpiece, and hot equipment can cause fires and

burns. Accidental contact of electrode to metal objects can cause

sparks, explosion, overheating, or fire. Check and be sure the area is

safe before doing any welding.

WELDING can cause fire or explosion.

D Remove all flammables within 35 ft (10.7 m) of the welding arc. If

this is not possible, tightly cover them with approved covers.

D Do not weld where flying sparks can strike flammable material.

D Protect yourself and others from flying sparks and hot metal.

D Be alert that welding sparks and hot materials from welding can

easily go through small cracks and openings to adjacent areas.

D Watch for fire, and keep a fire extinguisher nearby.

D Be aware that welding on a ceiling, floor, bulkhead, or partition can

cause fire on the hidden side.

D Do not weld on closed containers such as tanks, drums, or pipes,

unless they are properly prepared according to AWS F4.1 (see

Safety Standards).

D Do not weld where the atmosphere may contain flammable dust,

gas, or liquid vapors (such as gasoline).

D Connect work cable to the work as close to the welding area as

practical to prevent welding current from traveling long, possibly

unknown paths and causing electric shock, sparks, and fire

hazards.

D Do not use welder to thaw frozen pipes.

D Remove stick electrode from holder or cut off welding wire at

contact tip when not in use.

D Wear oil-free protective garments such as leather gloves, heavy

shirt, cuffless trousers, high shoes, and a cap.

D Remove any combustibles, such as a butane lighter or matches,

from your person before doing any welding.

D After completion of work, inspect area to ensure it is free of sparks,

glowing embers, and flames.

D Use only correct fuses or circuit breakers. Do not oversize or by-

pass them.

D Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B

for hot work and have a fire watcher and extinguisher nearby.

FLYING METAL or DIRT can injure eyes.

D Welding, chipping, wire brushing, and grinding

cause sparks and flying metal. As welds cool,

they can throw off slag.

D Wear approved safety glasses with side

shields even under your welding helmet.

BUILDUP OF GAS can injure or kill.

D Shut off shielding gas supply when not in use.

D Always ventilate confined spaces or use

approved air-supplied respirator.

MAGNETIC FIELDS can affect Implanted

Medical Devices.

D Wearers of Pacemakers and other Implanted

Medical Devices should keep away.

D Implanted Medical Device wearers should consult their doctor

and the device manufacturer before going near arc welding, spot

welding, gouging, plasma arc cutting, or induction heating

operations.

NOISE can damage hearing.

Noise from some processes or equipment can

damage hearing.

D Wear approved ear protection if noise level is

high.

Shielding gas cylinders contain gas under high

pressure. If damaged, a cylinder can explode. Since

gas cylinders are normally part of the welding

process, be sure to treat them carefully.

CYLINDERS can explode if damaged.

D Protect compressed gas cylinders from excessive heat, mechani-

cal shocks, physical damage, slag, open flames, sparks, and arcs.

D Install cylinders in an upright position by securing to a stationary

support or cylinder rack to prevent falling or tipping.

D Keep cylinders away from any welding or other electrical circuits.

D Never drape a welding torch over a gas cylinder.

D Never allow a welding electrode to touch any cylinder.

D Never weld on a pressurized cylinder − explosion will result.

D Use only correct shielding gas cylinders, regulators, hoses, and fit-

tings designed for the specific application; maintain them and

associated parts in good condition.

D Turn face away from valve outlet when opening cylinder valve.

D Keep protective cap in place over valve except when cylinder is in

use or connected for use.

D Use the right equipment, correct procedures, and sufficient num-

ber of persons to lift and move cylinders.

D Read and follow instructions on compressed gas cylinders,

associated equipment, and Compressed Gas Association (CGA)

publication P-1 listed in Safety Standards.

OM-235 281 Page 3

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near

combustible surfaces.

D Do not install unit near flammables.

D Do not overload building wiring − be sure power supply system is

properly sized, rated, and protected to handle this unit.

FALLING EQUIPMENT can injure.

D Use lifting eye to lift unit only, NOT running

gear, gas cylinders, or any other accessories.

D Use equipment of adequate capacity to lift and

support unit.

D If using lift forks to move unit, be sure forks are long enough to

extend beyond opposite side of unit.

D Keep equipment (cables and cords) away from moving vehicles

when working from an aerial location.

D Follow the guidelines in the Applications Manual for the Revised

NIOSH Lifting Equation (Publication No. 94−110) when manu-

ally lifting heavy parts or equipment.

OVERUSE can cause OVERHEATING

D Allow cooling period; follow rated duty cycle.

D Reduce current or reduce duty cycle before

starting to weld again.

D Do not block or filter airflow to unit.

FLYING SPARKS can injure.

D Wear a face shield to protect eyes and face.

D Shape tungsten electrode only on grinder with

proper guards in a safe location wearing proper

face, hand, and body protection.

D Sparks can cause fires — keep flammables away.

STATIC (ESD) can damage PC boards.

D Put on grounded wrist strap BEFORE handling

boards or parts.

D Use proper static-proof bags and boxes to

store, move, or ship PC boards.

MOVING PARTS can injure.

D Keep away from moving parts.

D Keep away from pinch points such as drive

rolls.

WELDING WIRE can injure.

D Do not press gun trigger until instructed to do

so.

D Do not point gun toward any part of the body,

other people, or any metal when threading

welding wire.

MOVING PARTS can injure.

D Keep away from moving parts such as fans.

D Keep all doors, panels, covers, and guards

closed and securely in place.

D Have only qualified persons remove doors, panels, covers, or

guards for maintenance and troubleshooting as necessary.

D Reinstall doors, panels, covers, or guards when maintenance is

finished and before reconnecting input power.

READ INSTRUCTIONS.

D Read and follow all labels and the Owner’s

Manual carefully before installing, operating, or

servicing unit. Read the safety information at

the beginning of the manual and in each

section.

D Use only genuine replacement parts from the manufacturer.

D Perform maintenance and service according to the Owner’s

Manuals, industry standards, and national, state, and local

codes.

H.F. RADIATION can cause interference.

D High-frequency (H.F.) can interfere with radio

navigation, safety services, computers, and

communications equipment.

D Have only qualified persons familiar with

electronic equipment perform this installation.

D The user is responsible for having a qualified electrician prompt-

ly correct any interference problem resulting from the installa-

tion.

D If notified by the FCC about interference, stop using the

equipment at once.

D Have the installation regularly checked and maintained.

D Keep high-frequency source doors and panels tightly shut, keep

spark gaps at correct setting, and use grounding and shielding to

minimize the possibility of interference.

ARC WELDING can cause interference.

D Electromagnetic energy can interfere with

sensitive electronic equipment such as

computers and computer-driven equipment

such as robots.

D Be sure all equipment in the welding area is

electromagnetically compatible.

D To reduce possible interference, keep weld cables as short as

possible, close together, and down low, such as on the floor.

D Locate welding operation 100 meters from any sensitive elec-

tronic equipment.

D Be sure this welding machine is installed and grounded

according to this manual.

D If interference still occurs, the user must take extra measures

such as moving the welding machine, using shielded cables,

using line filters, or shielding the work area.

OM-235 281 Page 4

1-4. California Proposition 65 Warnings

Welding or cutting equipment produces fumes or gases

which contain chemicals known to the State of California to

cause birth defects and, in some cases, cancer. (California

Health & Safety Code Section 25249.5 et seq.)

Battery posts, terminals and related accessories contain lead

and lead compounds, chemicals known to the State of

California to cause cancer and birth defects or other

reproductive harm. Wash hands after handling.

For Gasoline Engines:

Engine exhaust contains chemicals known to the State of

California to cause cancer, birth defects, or other reproduc-

tive harm.

For Diesel Engines:

Diesel engine exhaust and some of its constituents are

known to the State of California to cause cancer, birth

defects, and other reproductive harm.

1-5. Principal Safety Standards

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,

from Global Engineering Documents (phone: 1-877-413-5184, website:

www.global.ihs.com).

Safe Practices for the Preparation of Containers and Piping for Welding

and Cutting, American Welding Society Standard AWS F4.1, from Glob-

al Engineering Documents (phone: 1-877-413-5184, website:

www.global.ihs.com).

National Electrical Code, NFPA Standard 70, from National Fire Protec-

tion Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:

www.nfpa.org and www. sparky.org).

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,

from Compressed Gas Association, 4221 Walney Road, 5th Floor,

Chantilly, VA 20151 (phone: 703-788-2700, website:www.cganet.com).

Safety in Welding, Cutting, and Allied Processes, CSA Standard

W117.2, from Canadian Standards Association, Standards Sales, 5060

Spectrum Way, Suite 100, Ontario, Canada L4W 5NS (phone:

800-463-6727, website: www.csa-international.org).

Safe Practice For Occupational And Educational Eye And Face Protec-

tion, ANSI Standard Z87.1, from American National Standards Institute,

25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, web-

site: www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot

Work, NFPA Standard 51B, from National Fire Protection Association,

Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org.

OSHA, Occupational Safety and Health Standards for General Indus-

try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,

and Part 1926, Subpart J, from U.S. Government Printing Office, Super-

intendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954

(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—

phone for Region 5, Chicago, is 312-353-2220, website:

www.osha.gov).

U.S. Consumer Product Safety Commission (CPSC), 4330 East West

Highway, Bethesda, MD 20814 (phone: 301-504-7923, website:

www.cpsc.gov).

Applications Manual for the Revised NIOSH Lifting Equation, The Na-

tional Institute for Occupational Safety and Health (NIOSH), 1600

Clifton Rd, Atlanta, GA 30333 (phone: 1-800-232-4636, website:

www.cdc.gov/NIOSH).

1-6. EMF Information

Considerations About Welding And The Effects Of Low Frequency

Electric And Magnetic Fields

Welding current, as it flows through welding cables, will cause electro-

magnetic fields. There has been and still is some concern about such

fields. However, after examining more than 500 studies spanning 17

years of research, a special blue ribbon committee of the National

Research Council concluded that: “The body of evidence, in the

committee’s judgment, has not demonstrated that exposure to power-

frequency electric and magnetic fields is a human-health hazard.”

However, studies are still going forth and evidence continues to be

examined. Until the final conclusions of the research are reached, you

may wish to minimize your exposure to electromagnetic fields when

welding or cutting.

To reduce magnetic fields in the workplace, use the following

procedures:

1. Keep cables close together by twisting or taping them, or using a

cable cover.

2. Arrange cables to one side and away from the operator.

3. Do not coil or drape cables around your body.

4. Keep welding power source and cables as far away from opera-

tor as practical.

5. Connect work clamp to workpiece as close to the weld as possi-

ble.

About Implanted Medical Devices:

Implanted Medical Device wearers should consult their doctor and the

device manufacturer before performing or going near arc welding, spot

welding, gouging, plasma arc cutting, or induction heating operations.

If cleared by your doctor, then following the above procedures is recom-

mended.

Page is loading ...

OM-235 281 Page 9

2-5. Principales normes de sécurité

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,

de Global Engineering Documents (téléphone : 1-877-413-5184, site

Internet : www.global.ihs.com).

Recommended Safe Practices for the Preparation for Welding and Cut-

ting of Containers and Piping, American Welding Society Standard

AWS F4.1 de Global Engineering Documents (téléphone :

1-877-413-5184, site Internet : www.global.ihs.com).

National Electrical Code, NFPA Standard 70, de National Fire Protec-

tion Association, P.O. Box 9101, Quincy, MA 02269-9101 (téléphone :

617-770-3000, site Internet : www.nfpa.org).

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,

de Compressed Gas Association, 4221 Walney Road, 5th Floor, Chan-

tilly, VA 20151 (téléphone : 703-788-2700, site Internet :

www.cganet.com).

Code for Safety in Welding and Cutting, CSA Standard W117.2, de

Canadian Standards Association, 5060 Mississauga, Ontario, Canada

L4W 5NS (téléphone : 800-463-6727 ou à Toronto 416-747-4044, site

Internet : www.csa-international.org).

Safe Practice For Occupational And Educational Eye And Face Protec-

tion, ANSI Standard Z87.1, de American National Standards Institute,

11 West 43rd Street, New York, NY 10036-8002 (téléphone :

212-642-4900, site Internet : www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot

Work, NFPA Standard 51B, de National Fire Protection Association,

P.O. Box 9101, Quincy, MA 02269-9101 (téléphone : 617-770-3000,

site Internet : www.nfpa.org).

OSHA, Occupational Safety and Health Standards for General Indus-

try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,

and Part 1926, Subpart J, de U.S. Government Printing Office, Superin-

tendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954

(téléphone : 1-866-512-1800) (il y a 10 bureaux régionaux−−le télépho-

ne de la région 5, Chicago, est 312-353-2220, site Internet :

www.osha.gov).

2-6. Information EMF

Considérations sur le soudage et les effets de basse fréquence et des

champs magnétiques et électriques.

Le courant de soudage, pendant son passage dans les câbles de sou-

dage, causera des champs électromagnétiques. Il y a eu et il y a encore

un certain souci à propos de tels champs. Cependant, après avoir exa-

miné plus de 500 études qui ont été faites pendant une période de

recherche de 17 ans, un comité spécial ruban bleu du National

Research Council a conclu : « L’accumulation de preuves, suivant le

jugement du comité, n’a pas démontré que l’exposition aux champs

magnétiques et champs électriques à haute fréquence représente un

risque à la santé humaine ». Toutefois, des études sont toujours en

cours et les preuves continuent à être examinées. En attendant que les

conclusions finales de la recherche soient établies, il vous serait

souhaitable de réduire votre exposition aux champs électromagnéti-

ques pendant le soudage ou le coupage.

Pour réduire les champs magnétiques sur le poste de travail, appliquer

les procédures suivantes :

1. Garder les câbles ensemble, les torsader, les scotcher, ou les

recouvrir d’une housse.

2. Disposer les câbles d’un côté et à distance de l’opérateur.

3. Ne pas courber et ne pas entourer les câbles autour de votre

corps.

4. Garder le poste de soudage et les câbles le plus loin possible de

vous.

5. Connecter la pince sur la pièce aussi près que possible de la

soudure.

En ce qui concerne les implants médicaux :

Les porteurs d’implants doivent d’abord consulter leur médecin avant

de s’approcher des opérations de soudage à l’arc, de soudage par

points, de gougeage, du coupage plasma ou de chauffage par induc-

tion. Si le médecin approuve, il est recommandé de suivre les

procédures précédentes.

Page is loading ...

OM-235 281 Page 11

SECTION 3 − INTRODUCTION

3-1. Specifications

Rated Output

Max. Open

Circuit Voltage

Amps Input at Rated Output, 60 Hz, Single-Phase

200 V 230 V KVA KW

175 A at 25.5 VDC,

60% Duty Cycle

37.0

2.4*

32.5

2.3*

7.4

0.54*

6.3

0.30*

* While idling

Wire Type and Diameter

No Load

Wire Feed

Speed

Dimensions Weight

Solid Steel/

Stainless Steel

Aluminum Flux Cored

0−700 IPM

(0−17.8

m/min)

H: 32 in (813 mm)

W: 18-7/8 in (479 mm)

D: 37 in (940 mm)

185 lb

(84 kg)

.023 − .045 in

(0.6 − 1.2 mm)

.030 − .035 in

(0.8 − 0.9 mm)

.030 − .045 in

(0.8 − 1.2 mm)

3-2. Welding Power Source Duty Cycle And Overheating

Duty Cycle is percentage of 10 min-

utes that unit can weld at rated load

without overheating.

If unit overheats, thermostat(s)

opens, output stops, and cooling

fan runs. Wait fifteen minutes for

unit to cool. Reduce amperage or

voltage, or duty cycle before

welding.

NOTICE − Exceeding duty cycle

can damage unit or gun and void

warranty.

Overheating

A or V

Reduce Duty Cycle

Minutes

duty1 4/95 − 227 953-A

30 40 50 60 70 80 90 100

100

150

200

250

% DUTY CYCLE

WELD AMPERES

6 Minutes Welding 4 Minutes Resting

60%dutycycle

OM-235 281 Page 12

3-3. Volt-Ampere Curves

Volt-ampere curves show minimum

and maximum voltage and amper-

age output capabilities of unit.

Curves of other settings fall be-

tween curves shown.

va_curve1 4/95 − 240 913-A

0.0

5.0

10.0

15.0

20.0

25.0

30.0

35.0

40.0

0 50 100 150 200 250 300

Voltage

Amperage

OM-235 281 Page 13

SPOOL GUN

MIG GUN

CB2

CB1

3-4. Installing Welding Gun

Ref. 242 143-A

1 Drive Assembly

2 Gun Securing Knob

3 Gun End

Loosen knob. Insert gun end

through opening until it bottoms

against drive assembly. Tighten

knob.

4 Gun Trigger Plug

Insert plug into receptacle, and

tighten threaded collar.

5 MIG/Spool Gun Switch

Switch is shown in MIG position.

Close door.

SPOOL GUN

MIG GUN

OM-235 281 Page 14

3-5. Connecting To Weld Output Terminals

803 778-A

! Turn off power before connecting to

weld output terminals.

! Failure to properly connect weld

cables may cause excessive heat

and start a fire, or damage your

machine.

1 Weld Output Terminal

2 Supplied Weld Output Terminal Nut

3 Weld Cable Terminal

4 Copper Bar

Remove supplied nut from weld output ter-

minal. Slide weld cable terminal onto weld

output terminal and secure with nut so that

weld cable terminal is tight against copper

bar. Do not place anything between weld

cable terminal and copper bar. Make

sure that the surfaces of the weld cable

terminal and copper bar are clean.

Tools Needed:

3/4 in (19 mm)

2 3

Do not place

anything between

Correct Installation

Incorrect Installation

weld cable terminal

and copper bar.

3-6. Installing Work Clamp

1 Work Cable

Route cable out front panel opening

from inside.

2 Negative (−/Black) Output

Terminal

Connect cable to terminal.

3 Hardware

4 Work Clamp

Route cable through clamp handle

and secure as shown.

Close door.

Ref. 242 145-A

Tools Needed:

1/2, 3/4 in

OM-235 281 Page 15

3-7. Setting Gun Polarity For Wire Type

Tools Needed:

3/4 in

Ref. 242 145-A

Shown as shipped - Electrode Positive (DCEP):

For solid steel, stainless steel, aluminum, or flux

core with gas wires (GMAW).

Electrode Negative (DCEN):

Reverse lead connections at terminals from that

shown above for gasless flux core wires (FCAW).

Drive assembly becomes negative.

+ Positive Terminal

− Negative Terminal

Work Clamp Lead

Wire Drive Assembly Lead

Changing Polarity

3-8. Installing 2 lb Wire Spool And Adjusting Hub Tension

242 146-A

1 Keyed Washer

2 Wire Spool (2 LB)

3 Keyed Washer

4 Compression Spring

5 Washer

6 Nut

Assemble components in numer-

ical order as shown.

Hand tighten nut to create a slight

drag while rotating wire spool.

. Over tightening nut may

cause wire slippage.

OM-235 281 Page 16

3-9. Installing 10 lb Wire Spool And Adjusting Hub Tension

242 147-A

1 Spool Hub

2 Spool Hub Adapter

3 Spool Hub Nut

4 Keyed Washer (2)

5 Compression Spring

6 Washer

7 Nut

Assemble components in numer-

ical order as shown.

Slide spool hub adapter up on hub

for the smaller spool making sure

it is positioned in the anti-rotation

notches.

Secure hub nut on spool hub ad-

aptor.

Position remaining components.

Hand tighten nut to create a slight

drag while rotating wire spool.

. Over tightening nut may

cause wire slippage.

3-10. Installing 33 lb Wire Spool And Adjusting Hub Tension

242 148-A

1 Spool Hub

2 Spool Hub Adapter

3 Spool Hub Nut

4 Keyed Washer (2)

5 Compression Spring

6 Washer

7 Nut

Assemble components in numer-

ical order as shown.

Slide spool hub adapter up on hub

for the smaller spool making sure

it is positioned in the anti-rotation

notches.

Secure hub nut on spool hub ad-

aptor.

Position remaining components.

Hand tighten nut to create a slight

drag while rotating wire spool.

. Over tightening nut may

cause wire slippage.

OM-235 281 Page 17

3-11. Installing Gas Supply

242 687-A

Tools Needed:

1-1/8, 5/8 in

Rear Panel

. DO NOT use Argon/Mixed gas regulator/flowmeter

with CO

shielding gas. See Parts List for optional

gas regulator/flowmeter.

Obtain gas cylinder and chain to

running gear, wall, or other

stationary support so cylinder

cannot fall and break off valve.

1 Cap

2 Cylinder Valve

Remove cap, stand to side of valve,

and open valve slightly. Gas flow

blows dust and dirt from valve.

Close valve.

3 Cylinder

a Argon Or Mixed Gas

Cylinder

bCO

Cylinder

4 Regulator/Flowmeter

a Argon Or Mixed Gas

Regulator/Flowmeter

bCO

Regulator/Flowmeter

Install so face is vertical.

5 Regulator/Flowmeter Gas

Hose Connection

6 Welding Power Source Gas

Hose Connection For MIG

Gun

Connect supplied gas hose

between regulator/flowmeter gas

hose connection, and fitting on rear

of welding power source.

7 Gas Flow Adjustment Control

Typical flow rate is 20 cfh (cubic

feet per hour). Check wire

manufacturer’s recommended flow

rate.

Argon Gas Or

Mixed Gas

Gas

OM-235 281 Page 18

3-12. Positioning Jumper Links

242 688-A

! Turn off and disconnect input

power.

Check input voltage available at site.

1 Jumper Links Access Door

Open door.

2 Jumper Link Label

Check label − only one is on unit.

3 Input Voltage Jumper Links

Move jumper links to match input

voltage.

Close and secure access door.

Tools Needed:

3/8 in

200 VOLTS

230 VOLTS

S-153 980

OM-235 281 Page 19

3-13. Electrical Service Guide

Failure to follow these electrical service guide recommendations could create an electric shock or fire hazard. These recommenda-

tions are for a dedicated branch circuit sized for the rated output and duty cycle of the welding power source.

60 Hz Single

Phase

Input Voltage 200 230

Input Amperes At Rated Output 37.0 32.5

Max Recommended Standard Fuse Rating In Amperes

Circuit Breaker

, Time-Delay

45 40

Normal Operating

60 50

Min Input Conductor Size In AWG

10 10

Max Recommended Input Conductor Length In Feet (Meters)

(23)

102

(31)

Min Grounding Conductor Size In AWG

10 10

Reference: 2005 National Electrical Code (NEC) (including article 630)

1 Choose a circuit breaker with time-current curves comparable to a Time Delay Fuse.

2 “Time-Delay” fuses are UL class “RK5” .

3 “Normal Operating” (general purpose - no intentional delay) fuses are UL class “K5” (up to and including 60 amp), and UL class “H” ( 65 amp and

above).

4 Conductor data in this section specifies conductor size (excluding flexible cord or cable) between the panelboard and the equipment per NEC Table

310.16. If a flexible cord or cable is used, minimum conductor size may increase. See NEC Table 400.5(A) for flexible cord and cable requirements.

OM-235 281 Page 20

3-14. Selecting A Location And Connecting Input Power

Ref. 242 691-A / 802 286-E

! Do not move or operate unit

where it could tip.

18 in (457 mm) of

space for airflow

! Installation must meet all National

and Local Codes − have only quali-

fied persons make this installation.

! Special installation may be

required where gasoline or volatile

liquids are present − see NEC Ar-

ticle 511 or CEC Section 20.

! Disconnect and lockout/tagout in-

put power before connecting input

conductors from unit.

! Always connect green or green/yel-

low conductor to supply grounding

terminal first, and never to a line

terminal.

1 Rating Label

Supply correct input power.

2 Plug (NEMA Type 6-50P)

3 Receptacle NEMA Type 6-50R)

Connect plug to receptacle.

4 Input Power Cord.

5 Black And White Input Conductor (L1

And L2)

6 Green Or Green/Yellow Grounding

Conductor

7 Disconnect Device (switch shown in

the OFF position)

8 Disconnect Device Grounding

Terminal

9 Disconnect Device Line Terminals

Connect green or green/yellow grounding

conductor to disconnect device grounding

terminal first.

Connect input conductors L1 and L2 to dis-

connect device line terminals.

10 Over-Current Protection

Select type and size of over-current

protection using Section 3-13 (fused dis-

connect switch shown).

Close and secure door on disconnect

device. Remove lockout/tagout device,

and place switch in the On position.

230 VAC, 1

=GND/PE Earth Ground

OM-235 281 Page 21

3-15. Threading Welding Wire

1 Wire Spool

2 Welding Wire

3 Inlet Wire Guide

4 Pressure Adjustment Knob

5 Drive Roll

6 Outlet Wire Guide

7 Gun Conduit Cable

Lay gun cable out straight before

threading wire.

Tools Needed:

6 in

(150 mm)

. Hold wire tightly to keep it

from unraveling.

WOOD

Open pressure assembly. Pull and hold wire; cut off end. Push wire thru guides into gun;

continue to hold wire.

Close and tighten pressure

assembly, and let go of wire.

Lay gun cable out straight and

remove gun nozzle and contact tip.

Turn power ON.

Press gun trigger until wire

comes out of gun. Reinstall

contact tip and nozzle

Feed wire to check drive roll pressure.

Tighten knob enough to prevent slipping.

Cut off wire approximately 5/16 in (8 mm)

from contact tip. Close door.

242 692-A

. Hold wire in groove before

closing pressure assembly.

Tighten

OFF

POWER

Page is loading ...

Hobart H200L4-15 GUN User manual

Brand: Hobart

Model: H200L4-15 GUN

Category: Welding System

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

français: Hobart H200L4-15 GUN Manuel utilisateur

Hobart H200L4-15 GUN User manual

This manual is also suitable for

Hobart H200L4-15 GUN User manual

in other languages

Related papers