Fluke Juego de puntas de prueba con fusible TLK291 User manual

®

Model TLK291

Users Manual

PN 2438568

May 2005

2

(x)

(x) = hand-held area of probe bodies

Fuse Holder (FH)

figure 1

figure 3

figure 2

Transformer

CAT I

CAT II

CAT III

CAT IV

1

4

2

3

4

1) Inlet of supply cables 2) Electricity Meter

3) Ground cable 4) Side building



References marked on instru-

ment or in instruction manual:

Warning of a potential danger, comply with

instruction manual.

Caution! Dangerous voltage. Danger of electri-

cal shock.

Part protected throughout by DOUBLE INSULA-

TION or REINFORCED INSULATION.

Confirms to European directives.

Measurement Categories, refer to

figure 1 (page 2)

CAT I: For measurements performed on circuits not

directly connected to a mains supply.

CAT II: For measurements performed on circuits not

directly connected to the low-voltage insta l-

lation.

CAT III: For measurements performed in the building

installation.

CAT IV: For measurements performed at the source

of the low-voltage installation.

Read First: Safety Information

To avoid possible electric shock or personal in-

jury, follow these guidelines:

Read „Safety Information“ before use

Adhere to local and national safety codes. Indi-

vidual protective equipment must be used to

prevent shock and injury.

Use caution when working with voltages above

30 V ac rms, 42 V ac peak, or 60 V dc. These

voltages pose a shock hazard.

Check the test leads for continuity. Replace

damaged test leads before use.

Ensure that test leads and probes are fully

mated to each other and the equipment.

3

Appropriate Usage

The accessories may only be used under those

conditions and for those purposes for which it

was conceived. For this reason, safety refer-

ences, technical data (including environmental

conditions), and the usage in dry environments

must be followed.

If probes are modified by the user, operational

safety is no longer ensured.

Accessories-handle surface, refer to

figure 2 (page 2)

Only touch test leads and test probes at handle

surface provided. Never directly touch test probe

tips or touch test probes beyond the barrier.

Fuse Replacement

The fuse can be checked with a simple continuity

test.

Prior to fuse replacement, disconnect the acces-

sory (cable or probe) on both side every time.

Exclusively use fuses of voltage and current

values in compliance with the technical data

section. Using auxiliary fuses, in particular short-

circuiting fuse holders is prohibited and can

cause probe destruction or serious bodily injury

of operator.

Completely unsrew the fuse holder (FH). See figure 3

(page 2)

Remove defect fuse.

Push the fuse into the fuse holder.

Screw in fully the fuse holder to the end stop.

4

Cleaning

If the probes are dirty after use, cleam them by using

a damp cloth and a mild household detergent.

Prior to cleaning, ensure that probes are discon-

nected from external voltage supply and any

other instruments connected (such as UUT, con-

trol instruments, etc.).

Technical Data

For use with 4mm shrouded test leads such as

FLUKE TL224.

TLK 291 CAT III / 1000 V 0.5 A

Pollution Degree 2

Operation Temperature -0°...+40°C /

max. 80% rel. humidity

Storage Temperature -0°...+55°C /

max. 80% rel. humidity

Hight above MSL. up to 2000 meters

Fuse 500 mA / 1000 V / FF/

50 kA / (6.3 x 32 mm)

For assistance or information on Fluke products call:

800-443-5853 in the USA and Canada; 31-40-2-675-

200 in Europe or 425-446-5000 from all other coun-

tries; or visit us at our website

at www.fluke.com.

5

Page is loading ...

16

Fluke Corporation

P.O. Box 9090

Everett WA

98206-9090

Fluke Europe B.V.

P.O. Box 1186

5602 B.D. Eindhoven

Netherlands

05/2005 PTDBFTLK2910-00

Fluke Juego de puntas de prueba con fusible TLK291 User manual

This manual is also suitable for

Fluke Juego de puntas de prueba con fusible TLK291 User manual

in other languages

Related papers

Other documents