2. Gibson
  3. PGC2T(C,L) - VS
PGC2T(C,L) - VS

Gibson PGC2T(C,L) - VS, FG7T(A,K) - VS, FG7T(C,L) - VS, KG6T(A,K), KG6T(C,L), KG7T(A,K), KG7T(C,L), PGC2T(A,K) - FS Product information

  • Hello! I am an AI chatbot trained to assist you with the Gibson PGC2T(C,L) - VS Product information. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
FLAME
ROLL-OUT
SUPPLY
AIR LIMIT
11
22
33
44
55
66
77
88
99
FLAME SENSOR
11
4
1
8
7
10
5
2
9
3
12
6
LINE- N
XMFR-N
LINE
LINE
XMFR
EAC
HUM
LINE- N
14325
R
C
TX
RX
W
COM
IGNITOR
DOOR
SWITCH
RCY/Y2 W2GW1Y1
1
2
1
2
BLACK
BLACK
WHITE
WHITE
WHITE
ORANGE
BLUE
BLUE
YELLOW
RED
BLACK
BLACK
WHITE
BLUE
ORANGE
YELLOW
WHITE
RED
BLACK
CFM
MOTOR
GNDSEN
DHUM
Y1
H
L2-OUT
RED
GREEN
L2-IN
L1-IN
L1OUT
Y1Y/Y2W
CR
HP
SPEED
COMMON
PWM
MODE
OPEN
OPEN
FAULT
R
C
GND
RX
TX
W
C
DX-
DX+
R
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
WHITE
ORANGE
YELLOW
RED
BLACK
24 V
120 V
WHITE
BLACK
WHITE W/ BLK STRIPES
BLK W/ WHITE STRIPES
1234
1234
BLUE
GAS
VALVE
LO
HI
C
INDUCER
H
L
C
123
123
BLACK
BLACK
COOL
FAN SPEED
HEAT
BLWR OFF
DELAY
LOW
PRESSURE
SWITCH
HIGH
PRESSURE
SWITCH
RED
RED
RED
PART OF
MOTOR
123
123
BLOWER
LIMIT
BLOWER
LIMIT
BLOWER
DECK LIMIT
1
2
3
1
2
3
BLUE
BLUE
BLUE
BLACK
BLACK 120V
WHITE
BLACK
BLACK
BLACK
WHITE
BLACK
BLACK
BLACK
WHITE
WHITE
(NEUTRAL)
BLACK
WHITE
WHITE
RED
RED
GREEN
GROUND
GREEN
BROWN
YELLOW
BROWN
VIOLET
VIOLET
ORANGE
ORANGE
VENT LIMIT
(ON SELECT
MODELS)
MOTOR CHOKE
(ON 3/4 AND 1HP
MODELS ONLY)
For 80+ and 90+ 2-Stage Variable Speed Downflow Furnaces
WIRING DIAGRAM
710919B
FIELD WIRING
LEGEND:
LOW VOLTAGE
HIGH VOLTAGE
(Replaces 710919A)
Refer to the Installation Instructions
provided with the kit for the proper
heating and cooling speeds for your
application.
If any of the origInal wire as supplied with the
furnace must be replaced, it must be replaced
with wiring material having a temperature
rating of at least 105° C.
Use copper conductors only.
This wiring diagram shows connections and
termination required for the blower kit only.
Use in addition to the wiring diagram for the
furnace.
Green LED Red LED
Control Fault (No Power) Off Off
L1 / Neutral Polarity Fault Flash Flash
1 Hour Lockout
Normal Operation On On
Pressure Switch Closed Fault On Flash
Pressure Switch Open Fault Flash On
Open Limit Switch Fault Flash Off
Low Flame Sensor Signal
Flame Present
Diagnostic Description
FAULT CONDITIONS
Diagnostic Description
Yellow LED
Continuous Flash
On
Alternating Flash
Motor Fault On Off
04/11
BLACK
/