2. Hyundai
  3. R227DP Series

Hyundai R227DP Series, R247DP Series Product End-Of-Life Disassembly Instructions

  • Hello! I am an AI chatbot trained to assist you with the Hyundai R227DP Series Product End-Of-Life Disassembly Instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Product End-of-Life Disassembly Instructions
Product Category: Monitors and Displays
Marketing Name / Model
[List multiple model if applicable]
LCD Monitor
/
R227DP*/
R247DP*
Purpose: The document is intended for use by end-of-life recyclers or treatment facilities. It provides the basic
instructions for the disassembly of Hyundai IT products to remove components and materials requiring selective
treatment, as defined by EU directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE).
1.1 Items listed below are classified as requiring selective treatment.
1.2 Enter the quantity of items contained within the product which require selective treatment in the right column, as
applicable.
Item Description Notes
Quality
of items
included
in product
Printed Circuit Board (PCB) or Printed Circuit
Assemblies (PCA)
With a surface greater than 10 sq
Main board, LCD driver board
2
Batteris
All types including standard alkaline and lithium
coin or button style batteries None
-
Mercury-containing components
For example, mercury in lamps, display backlights.
Scanner lamps, swithches, batteries None
-
Liquid Crystal Display (LCD) with a surface
greater than 100 sq cm
Included background illuminated displays with gas
discharge lamps
1
Cathode Ray Tubes (CRT) None
Capacitors / Condensers (Containing PCB/PCT) None
Electrolytic Capacitors / Condensers measuring
greater than 2.5 cm in diameter or height
None -
External electrical cables and cords DP cable 1
Gas Discharge Lamps None
Plastics containing Brominated Flame
Retardants weighing > 25 grams (not including
PCBs or PCAs already listed as a separate item
above)
None
Components and parts containing toner and ink,
including liquids, semi-liquids (gel/paste) and
toner
Include the cartridges, print heads, tubes, vent
chambers, and service stations. None
Components and wates containing asbestos None
Components, parts and materials containing
refactory ceramic fibers
None
Components, parts and material containing
radioactive substances
None
2.0 Tools Required
List the type and size of the tools that would typically be used to disassemble the product to a point where
components and materials requiring selective treatment can be removed.
Tool Description
Tool Size (if
applicable)
Screwdrivers
1
Plastic Jig
1
3.0 Product Disassembly Process
List the basic steps that should typically be followed to remove components and materials requiring selective
tratement:
1. With the aid of a screwdriver, loosen the four screws of stand.
2. Loosen the two screws of rear cover with screwdriver and then disassemble the rear cover from set.
3. Disconnect the backlight wire from the panel.
4. Loosen the three screws of driver board with screwdriver then disassemble driver board from set.
5. Loosen the six screws of mainboard cover with screwdriver then disassemble mainboard cover from set.
6. Loosen the four screws of mainboard with screwdriver then disassemble mainboard from set.
7. Loosen the four screws of speakers with screwdriver then disassemble speakers from set.
8. Disconnect the LVDS cable from the panel.
9. Loosen the five screws of front frame with screwdriver.
10. Loosen the six screws of Middle frame with screwdriver then disassemble middle frame from set.
3-1. Disassemble and Assemble
3-2. Disassemble Product
1) Unscrew the screw using the driver.
(*Tool)
2) Open Rear Cover with Tool.
6) Unscrew with Driver 2points
7) After unlock hook parts, separate Plastic Mold from LCD Module Assembly.
Screw
Screw
4) Open the Rear cover from Front cover
5) Separate cables and Remove the REAR cover Assembly from Front cover Assembly.
Separate the KEY board and remove Speakers with screw driver.
Key Pad
Screw
3) Separate Rear Cover with Tool
LCD module Assembly
Front mold
8) Separate the Main board from Rear Cover.
Unscrew with Driver 5points.
Separate the main board.
Main board Assembly.
Separate cables.
Main board
Cables
9) Separate the board of LCD driver board on the Panel.
Unscrew with Driver 3points
Press the film by hand and remove it from the T-con board.
/