Hunter Fan 23689 Owner's manual

Brand: Hunter Fan

Model: 23689

Type: Owner's manual

This manual is also suitable for

23687

41863-01 • 08/04/04

Hunter Fan Company 41863-01 • 08/04/04

41863-01 • 08/04/04 Hunter Fan Company

Your new Hunter

ceiling fan is an addition to your home or oce that

will provide comfort and performance for many years. is installation

and operation manual gives you complete instructions for installing

and operating your fan.

We are proud of our work. We appreciate the opportunity to supply

you with the best ceiling fan available anywhere in the world.

Before installing your fan, for your records and warranty assistance,

record information from the carton and Hunter nameplate label

(located on the top of the fan motor housing).

Cautions and Warnings

• Read this entire manual carefully before beginning installation. Save

these instructions.

• Use only Hunter replacement parts.

• To reduce the risk of personal injury, attach the fan directly to the

support structure of the building according to these instructions,

and use only the hardware supplied.

• To avoid possible electrical shock, before installing your fan,

disconnect the power by turning o the circuit breakers to the

outlet box and associated wall switch location. If you cannot lock

the circuit breakers in the o position, securely fasten a prominent

warning device, such as a tag, to the service panel.

• All wiring must be in accordance with national and local electrical

codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a

qualied electrician.

• To reduce the risk of personal injury, do not bend the blade

attachment system when installing, balancing, or cleaning the fan.

Never insert foreign objects between rotating fan blades.

• To reduce the risk of re, electrical shock, or motor damage, do not

use a solid-state speed control with this fan. Use only Hunter speed

controls.

For Your Records and Warranty

Assistance

Model Name: _____________________

Catalog/Model No.: ________________

Serial No.: _______________________

Date Purchased: ___________________

Where Purchased: _________________

For reference also attach your receipt or a

copy of your receipt to the manual.

Table of Contents

1 • Getting Ready ...................................................4

2 • Installing the Ceiling Plate..........................5

3 • Assembling and Hanging the Fan..........6

4 • Wiring the Fan..................................................8

5 • Installing the Canopy and

Canopy Trim Ring............................................9

6 • Assembling the Blades.............................. 10

7 • Installing the Light Kit............................... 11

8 • Operating and Cleaning

Your Ceiling Fan ............................................ 13

9 • Operating the Remote Control

and Mounting the Holder...................... 14

10 • Troubleshooting......................................... 15

Welcome

Hunter Fan Company 41863-01 • 08/04/04

41863-01 • 08/04/04 Hunter Fan Company

Installer’s Choice and Optional Accessories

Understanding Mounting and Installer’s Choice®

Hunter’s patented 3-position mounting system provides you maximum

installation  exibility and ease. You can install your Hunter fan in one

of three ways, depending on ceiling height and your preference: Low

Pro le, Standard, or Angle mounting.  e steps in this manual include

instructions for all three Installer’s Choice mounting methods.

Considering Optional Accessories

Consider using Hunter’s optional accessories, including a wall-mounted

or remote speed control. To install and use the accessories, follow

the instructions included with each product. For quiet and optimum

performance of your Hunter fan, use only Hunter speed controls.

Low Pro le Mounting  ts close to the

ceiling, for recommended or low ceilings

less than 8 feet high

Standard Mounting hangs from

the ceiling by a downrod (included),

recommended for ceilings 8 feet or higher

Angle Mounting recommended for a

vaulted or angled ceiling

For ceilings higher than 8 feet, you

can purchase Hunter extension

downrods. All Hunter fans use sturdy

3/4” diameter pipe to assure stability

and wobble-free performance.

Hunter Fan Company 41863-01 • 08/04/04

41863-01 • 08/04/04 Hunter Fan Company

To install a ceiling fan, be sure you can do the following:

• Locate the ceiling joist or other suitable support in ceiling.

• Drill holes for and install wood screws.

• Identify and connect electrical wires.

• Lift 40 pounds.

If you need help installing the fan, your Hunter fan dealer can direct

you to a licensed installer or electrician.

Gathering the Tools

You will need the following tools for installing the fan:

• Electric drill with 9/64” bit

• Standard screwdriver

• Phillips-head screwdriver

• Wrench or pliers

Check Your Fan Parts

Carefully unpack your fan to avoid damage to the fan parts. Check

for any shipping damage to the motor or fan blades. If one of the fan

blades was damaged in shipment, return all the blades for replacement.

If any parts are missing or damaged, contact your Hunter dealer or call

Hunter Parts Department at 888-830-1326.

Preparing the Fan Site

Before you begin installing the fan, follow all the instructions in

the pullout sheet called “Preparing the Fan Site.” Proper ceiling fan

location and attachment to the building structure are essential for

safety, reliable operation, maximum e ciency, and energy savings.

1 • Getting Ready

Installing Multiple Fans?

If you are installing more than

one fan, keep the fan blades in

sets, as they were shipped.

Hunter Fan Company 41863-01 • 08/04/04

41863-01 • 08/04/04 Hunter Fan Company

2-1. Drill two pilot holes into the wood support structure through the

outermost holes in the outlet box. e pilot holes should be 9/64”

in diameter.

2-2. Your fan comes with four neoprene noise isolators (“Isolators”).

Position the isolators between the ceiling plate and ceiling by

inserting the raised areas on each isolator into the holes in the

ceiling plate.

2-3. read the lead wires from the outlet box down through the hole

in the middle of the ceiling plate.

2-4. Align the slotted holes in the ceiling plate with the pilot holes you

drilled in the wood support structure. For proper alignment use

slotted holes directly across from each other.

Note: e isolators should be ush against the ceiling.

2-5. Place a at washer on each of the two 3” screws and pass the

screws through the slotted holes in the ceiling plate into the pilot

holes you drilled.

Tighten the screws into the 9/64” pilot holes; do not use lubricants

on the screws. Do not over tighten.

Step 2-2

Flat Washer

3” Screw

Steps 2-3 – 2-5

2 • Installing the Ceiling Plate

For Angled Ceilings: Be sure to

orient the ceiling plate so that the

arrows printed on the ceiling plate are

pointing towards the ceiling peak.

Ceiling

Plate

Hunter Fan Company 41863-01 • 08/04/04

41863-01 • 08/04/04 Hunter Fan Company

You can assemble your fan for standard mounting (steps 3-1 – 3-2) or

for low pro le mounting (steps 3-3 – 3-4).

To install the remote control you will need to strip electrical wires. If

you are uncomfortable doing so, seek help from a quali ed electrician.

3-1. To assemble fan to hang down from a  at or angled ceiling, insert

the downrod through the canopy and canopy trim ring. Feed the

wires from the fan through the downrod.

3-2. Screw the downrod into the fan assembly. Tighten the set screw.

Skip to Step 3-5.

CAUTION:  e downrod has a special coating on the threads.

Do not remove this coating; the coating prevents the downrod from

unscrewing. Once assembled, do not remove the downrod.

3-3. To assemble the fan to hang from a low ceiling, place the low

pro le washer (lip up) into the canopy. Be sure the green ground

wire is pointing up toward the ceiling.

Note: For low pro le mounting, the downrod is replaced with the

low pro le washer. See Steps 3-3 – 3-4.

3-4. Align the holes in the washer with the holes in the adapter.

Assemble securely with three #8-32 x 1” screws.

3-5. Before installing the remote control, change the position of the

jumper switches in the transmitter and the receiver. Be sure the

position of the jumper switches matches. If they don’t match, the

controller will not function. For instructions on how to set the

jumper switches, read the box below.

Steps 3-1 – 3-2

Steps 3-3 – 3-4

3 • Assembling and Hanging the Fan

#8-32 x 1” Screw

Low Pro le Washer

Downrod

Canopy

Trim Ring

Set Screw

Setting Jumper Switches

When two or more fans are located near each other, you may desire to have the receiver/

transmitter for each fan set to a di erent code, so that the operation of one fan does not

a ect the operation of the other fans.

In the transmitter you can access the jumpers from the battery compartment.  e

jumpers are very small. You can move them most easily using a small pair of pliers or

tweezers. IMPORTANT! Before you change jumper switches, make sure the battery is not

connected to the transmitter.

Hunter Fan Company 41863-01 • 08/04/04

41863-01 • 08/04/04 Hunter Fan Company

Step 3-9

U-shaped

Hole

3-6. Install the included 12-volt battery into the transmitter.

3-7. Cut the lead wires from the fan a maximum length of 3-1/2 inches

from the top of the downrod or the motor adapter (depending on

the mounting method you selected.). Using wire strippers on the

22AWG setting, strip 5/16 inch from each lead wire coming from

the fan.

3-8. Identify the shorter wires coming out of the remote receiver. Using

the small wire nuts provided, connect the shorter receiver wires to

the matching colored wires coming out of the fan. To connect the

wires, hold the bare metal leads together and place a small wire

nut over them, then twist clockwise until tight.

CAUTION: Be sure no bare wire or wire strands are visible after

making connections.

Note that you will use the longer black wire and white wire

coming from the remote receiver later when wiring to the power

wires from the ceiling. You will connect all the ground wires later

too.

3-9. Raise the fan and place the hook on the ceiling plate through the

U-shaped hole in the rim of the canopy.

WARNING: Fan may fall if not assembled as directed in these

installation instructions.

3-10.

Align the hooks on the receiver with the appropriate slots in the

ceiling plate. Also be sure the slot in the receiver and the hook in

the ceiling plate line up. Snap the receiver into place on the ceiling

plate.

Step 3-10

CAUTION: e remote control device complies with part 15 of the FCC rules.

Changes or modications not expressly approved by Hunter Fan Company could void

your authority to operate this equipment.

Operation is subject to the following two conditions:

1. is device may not cause harmful interference.

2. is device must accept any interference received, including interference that may

cause undesired operation.

Note: Use with a fan that incorporates an air gap switch (normal on-o wall switch).

WARNING: Maximum fan load is 100 Watts; maximum lamp is 300 Watts. Do not

use any speed control with this product.

Receiver

Small Wire Nut

Receiver

Hook

Hunter Fan Company 41863-01 • 08/04/04

41863-01 • 08/04/04 Hunter Fan Company

4 • Wiring the Fan

All wiring must be in accordance with national and local electrical

codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a

qualied electrician.

4-1. Disconnect the power by turning o the circuit breakers to the

outlet box and associated wall switch location.

4-2. To connect the wires, hold the bare metal leads together and place

a wire nut over them, then twist clockwise until tight. For all these

connections use the larger wire nuts provided.

CAUTION: Be sure no bare wire or wire strands are visible after

making connections.

4-3. Connect the ground wire from the ceiling to the green ground

wire from the ceiling plate and the green ground wire from the

downrod or low prole washer.

4-4. Working in the open section of the receiver, connect the white

and black wires from the ceiling as follows:

•

e white (common) power wire from the ceiling to the longer

white wire from the receiver (marked on red tag “NEUTRAL IN”)

• e black power wire from the ceiling to the longer black wire

from the receiver (marked on red tag “LIVE IN”)

4-5. Push all wires and wire nuts back through the ceiling plate hole

into the outlet box.

4-6. Run the white antenna wire from the receiver through one of the

slots in the ceiling plate so that it rests between the ceiling plate

and the ceiling. Push it to the edge of the ceiling plate for clear

reception.

Wire Nut

Receiver

Step 4-4

Steps 4-2 – 4-3

Hunter Fan Company 41863-01 • 08/04/04

41863-01 • 08/04/04 Hunter Fan Company

5-1. Holding the canopy, raise the fan o the hook.

5-2. Align the slots in the canopy with the tabs on the ceiling plate.

5-3. Raise the canopy over the ceiling plate. Rotate the canopy

clockwise until the tabs on the ceiling plate totally engage with

the slots in the canopy.

5-4. Loosely assemble the three canopy screws into the canopy one at

a time. Once all three screws are in, tighten them.

5-5. Using both hands, push the canopy trim ring up to the top of the

canopy.  e canopy trim ring will snap and lock into place.

5 • Installing the Canopy and Canopy Trim Ring

Should you need to remove the canopy

trim ring, follow these steps:

1. Locate the tab indicators, small

bumps on top of tabs.

2. Press  rmly on opposite sides of the

ring towards the canopy.  e tabs

will  ex out releasing the trim ring

from the canopy

Canopy

Screw

Step 5-2

Canopy Trim

Ring

Canopy

Ceiling Plate

Step 5-3

Steps 5-4 – 5-5

Hunter Fan Company 41863-01 • 08/04/04

41863-01 • 08/04/04 Hunter Fan Company

Hunter fans use several styles of fan blade irons (brackets that hold the

blade to the fan).

6-1. Your fan may include blade grommets. If your fan has grommets,

insert them by hand into the holes on the blades.

6-2. Attach each blade to a blade iron using three blade assembly

screws. If you used grommets, the blades may appear slightly loose

after screws are tightened. is is normal.

6-3. Remove the blade mounting screws and rubber shipping bumpers

from the motor.

6-4. For each blade, insert one blade mounting screw through the

blade iron, and attach lightly to the fan. Insert the second blade

mounting screw, then securely tighten both mounting screws.

6 • Assembling the Blades

Step 6-1 (Detail)

Blade Assembly

Screws

Use with grommet

Use without grommet

Blade Mounting

Screw

Grommet

Steps 6-1 – 6-2

Step 6-4

Hunter Fan Company 41863-01 • 08/04/04

41863-01 • 08/04/04 Hunter Fan Company

WARNING: Use only the light xture supplied with this fan model.

7-1. To attach the upper switch housing, partially install two #6-32 x

3/8” housing assembly screws into the switch housing mounting

plate.

7-2. Feed the upper plug connector through the center opening of the

housing.

7-3. Align the keyhole slots in the housing with the housing assembly

screws.

7-4. Turn the housing counterclockwise until the housing assembly

screws are rmly situated in the narrow end of the keyhole slots.

Install the remaining #6-32 x 3/8” screw into the housing. Tighten

all three screws rmly.

CAUTION: Make sure the upper switch housing is securely attached

to the switch housing mounting plate. Failure to properly attach and

tighten all three assembly screws could result in the switch housing and

light xture falling.

7-5. To attach the lower switch housing, connect the upper plug

connector from the motor to the lower plug connector in the

lower switch housing assembly.

Note: Both plug connectors are polarized and will only t together

one way. Make sure the connectors are properly aligned before

connecting them. Incorrect connection could cause improper

operation and damage to the product.

7-6. Place the lower switch housing assembly over the upper switch

housing. Align the side screw holes in the upper and lower switch

housings. Attach the lower switch housing to the upper switch

housing with three #6-32 x 3/8” housing assembly screws.

Steps 7-1 – 7-3

Housing

Assembly

Screw

7 • Installing the Light Kit

Housing

Assembly Screw

Lower Switch

Housing

Plug

Connector

Plug

Connector

Detail

Steps 7-5 – 7-6

Upper

Switch

Housing

Hunter Fan Company 41863-01 • 08/04/04

41863-01 • 08/04/04 Hunter Fan Company

7-7. To install the glass shades. Place the silencer band around the neck

of each glass shade. Insert each glass shade in a shade cup.

7-8. Install and tighten the three thumb screws. Do not overtighten.

7-9. Install medium base incandescent light bulbs, maximum 60 Watt.

Step 7-7 – 7-8

Shade Cup

Silencer Band

Glass Shade

umb

Screw

7 • Installing the Light Kit (continued)

Hunter Fan Company 41863-01 • 08/04/04

41863-01 • 08/04/04 Hunter Fan Company

8-1. Turn on electrical power to the fan.

8-2.  e fan pull chain controls power to the fan.  e pull chain has

four settings in sequence: High, Medium, Low and O .

• Pull the chain slowly to change settings.

• Release slowly to prevent the chain from recoiling into the

blades.

•  e chain uses a breakaway connector that separates if the

chain is jerked. If this happens, simply reinsert the chain into

the connector.

8-3.  e light pull chain controls power to the light.  e pull chain has

two settings: On and O .

8-4. Ceiling fans work best by blowing air downward (counterclockwise

blade rotation) in warm weather to cool the room with a direct

breeze. In winter, having the fan draw air upward (clockwise blade

rotation) will distribute the warmer air trapped at the ceiling

around the room without causing a draft.

8-5. For cleaning  nishes, use a soft brush or lint-free cloth to prevent

scratching. A vacuum cleaner brush nozzle can remove heavier

dust. Remove surface smudges or accumulated dirt and dust using

a mild detergent and a slightly dampened cloth. You may use

an artistic agent, but never abrasive cleaning agents as they will

damage the  nish.

8-6. Clean wood  nish blades with a furniture polishing cloth.

Occasionally, apply a light coat of furniture polish for added

protection and beauty. Clean painted and high-gloss blades in the

same manner as the fan  nish.

To Change Air ow Direction

Turn the fan o and let it come to a complete

stop. Slide the reversing switch on the fan to the

opposite position. Restart fan.

Reversing

Switch

In warm weather, use

downward air  ow pattern

In cold weather, use upward

air  ow pattern

8 • Operating and Cleaning Your Ceiling Fan

Hunter Fan Company 41863-01 • 08/04/04

41863-01 • 08/04/04 Hunter Fan Company

9-1. e remote transmitter has individual buttons for turning the fan

o and on and controlling the light and fan speed.

9-2. For best operation, start the fan by pressing high, then select your

desired speed.

9-3. e light button turns the light on to full brightness. To dim the

light, hold the light button down until you reach your desired

brightness. Push the light button again to turn o the light.

9-4. Press the OFF button to turn the fan o.

9-5. When necessary, replace the battery with a 12-volt type 23A, MN-

21 battery or equivalent.

9-6. You can mount the remote holder to any toggle switch plate with

the screws already in the switch plate. Or, you can simply mount

the remote holder on the wall.

9 • Operating the Remote Control and Mounting the Holder

Fan Light

Steps 9-1 – 9-4

Step 9-6

Step 9-5

Fan Speed

High

Fan Speed

Medium

Fan Speed

Low

Fan O

Hunter Fan Company 41863-01 • 08/04/04

41863-01 • 08/04/04 Hunter Fan Company

Problem: Nothing happens; fan does not move.

1. Turn power on, replace fuse, or reset breaker.

2. Loosen canopy, check all connections according to the wiring the

fan section.

3. Check the plug connection in the switch housing.

4. Push motor reversing switch  rmly up or down to ensure that the

switch is engaged.

5. Pull the pull chain to ensure it is on.

6. Remove the shipping bumpers.

Problem: Noisy operation.

1. Tighten the blade bracket screws until snug.

2. Tighten the blade screws until snug.

3. Check to see if the blade is cracked. If so, replace all the blades.

4. Change to an approved speed control.

5. Be sure that the glass is secure.

6. Check and tighten the screws in the switch housing mounting

plate and in the upper and lower switch housing.

Problem: Excessive wobbling.

1. If your fan wobbles when operating, use the enclosed balancing kit

and instructions to balance the fan.

2. Tighten all blade and/or blade iron screws.

3. Turn power o , support fan very carefully, and check that the

hanger ball is properly seated.

If you need parts or service assistance, please call

888-830-1326 or visit us at our WEB site at

http://www.hunterfan.com.

Hunter Fan Company

2500 Frisco Avenue

Memphis, Tennessee 38114

10 • Troubleshooting

Hunter Fan 23689 Owner's manual

Brand: Hunter Fan

Model: 23689

Type: Owner's manual

This manual is also suitable for

23687

Download PDF

report

Hunter Fan 23689 Owner's manual

This manual is also suitable for

Hunter Fan 23689 Owner's manual

Related papers