Ikelite B1A Ikelite ICS-5 Bulkhead with Connector (Replacement) User manual

Type
User manual

Ikelite B1A Ikelite ICS-5 Bulkhead with Connector (Replacement)

The Ikelite B1A Ikelite ICS-5 Bulkhead with Connector (Replacement) is a replacement bulkhead for the Ikelite ICS-5 housing. It allows you to connect your camera to the housing's electrical system, enabling you to use strobes, focus lights, and other accessories. The bulkhead is made of durable materials and is designed to withstand the rigors of underwater use.

Here are some of the features and possible use cases of the Ikelite B1A Ikelite ICS-5 Bulkhead with Connector (Replacement):

  • Durability: The bulkhead is made of durable materials and is designed to withstand the rigors of underwater use.

Ikelite B1A Ikelite ICS-5 Bulkhead with Connector (Replacement)

The Ikelite B1A Ikelite ICS-5 Bulkhead with Connector (Replacement) is a replacement bulkhead for the Ikelite ICS-5 housing. It allows you to connect your camera to the housing's electrical system, enabling you to use strobes, focus lights, and other accessories. The bulkhead is made of durable materials and is designed to withstand the rigors of underwater use.

Here are some of the features and possible use cases of the Ikelite B1A Ikelite ICS-5 Bulkhead with Connector (Replacement):

  • Durability: The bulkhead is made of durable materials and is designed to withstand the rigors of underwater use.
B1A Bulkhead
Product # 46002
Included in the Box
B1A Bulkhead # 46002
Important Notices
» It is recommended to vacuum test and water pressure
test or take the housing to depth without a camera
installed after installing or replacing the bulkhead.
» Do not submerge without a compatible plug or
waterproof bulkhead cap attached.
» Always attach a waterproof bulkhead cap when not in
use.
Installation and Use
Installing the B1A Bulkhead
1.
Carefully remove the existing bulkhead or accessory port
plug using an 11/16” wrench.
2.
Remove the nut from the end of the bulkhead with
the cord coming out. Check that the sealing surface
and o-ring on the bulkhead are clean. No lubricant is
necessary.
3.
Thread the bulkhead into the 1/2-20 hole in the top of the
housing being careful not to cross-thread.
4.
Use an 11/16” wrench to carefully tighten down the
bulkhead just until it touches the case. Do not over-
tighten.
5.
Re-attach the nut on the inside of the case. Tighten snug
with a 5/8” wrench.
Installing the Hotshoe
1.
Align hotshoe and bulkhead connector ends and push
together until tab clicks into place.
Maintenance and Storage
Post-Dive
1.
Submerge the fully assembled system in clean, fresh
water after each use.
2.
Remove the system from the rinse tank and ush with
running fresh water.
3.
Dry the system with a clean, lint-free cloth.
4.
Separate the plug or cap from the bulkhead and
lubricate the threads and o-ring(s) every 1-2 days during
continuous use and prior to storage.
Limited Warranty
This Ikelite product is warranted against any manufacturing
defects for a period of one (1) year from the original date
of purchase. To obtain warranty service, the product must
be returned to Ikelite postage paid. Ikelite will, at its sole
discretion, repair or replace such products, and will return
to customer postage paid. All other claims of any nature are
not covered. Except as mentioned above, no other warranty
expressed or implied applies to this Ikelite product.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Ikelite B1A Ikelite ICS-5 Bulkhead with Connector (Replacement) User manual

Type
User manual

Ikelite B1A Ikelite ICS-5 Bulkhead with Connector (Replacement)

The Ikelite B1A Ikelite ICS-5 Bulkhead with Connector (Replacement) is a replacement bulkhead for the Ikelite ICS-5 housing. It allows you to connect your camera to the housing's electrical system, enabling you to use strobes, focus lights, and other accessories. The bulkhead is made of durable materials and is designed to withstand the rigors of underwater use.

Here are some of the features and possible use cases of the Ikelite B1A Ikelite ICS-5 Bulkhead with Connector (Replacement):

  • Durability: The bulkhead is made of durable materials and is designed to withstand the rigors of underwater use.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI