Symantec J5300 40T Quick start guide

Brand: Symantec

Model: J5300 40T

Type: Quick start guide

Quick Start Guide

Security Analytics J5300 40T Direct-Attached Storage

Page 1

Date of Publication: 15 August 2017

SA-J5300-DAS-40T

Security Analytics appliances that have two RAID controllers can support up to three storage

modules per RAID controller. Attach the storage modules to the head unit in the order shown

below, using SAS-3 to SAS-3 cables:

Extend the rail to the front post and insert the studs into the corresponding mounting posts.

a. Use the rail screws to anchor the rail to the

front post.

b. After verifying that the rails are aligned,

secure, and stable, place the enclosure on

therails.

c. Insert the screws through the mounting holes

on either side of the enclosure and then

secure them with the cage nuts.

d. Replace the drives in the enclosure.

Two sets of cables are included with the J5300: one set for a SAS-3 environment and another for a

mixed SAS-2 and SAS-3 environment.

Orient each rail so that the L-shaped shelf is at the bottom and toward the front of therack.

a. Press the spring lock on the other end of the

rail, insert the studs into the holes on the

rear post, and release the lock so that it grips

the rail.

b. Use the rail screws to anchor the rail to the

rear post.

Unpack the shipment container and verify the contents of the box. Security Analytics J5300 40T

Direct-Attached Storage ships with the following components:

Before installing the J5300 enclosure in the rack, perform these steps:

a. Peel off the protective plastic sheet from the top and the bottom of the enclosure.

b. Remove the drives from the enclosure to reduce the weight:

o Press the release button on each drive to

unlock the drive carrier. The drive-carrier

handle swings out.

o Grasp the handle and gently pull the

drive carrier out of the J5300 and place it

on a static-free surface.

To install the J5300 enclosure into a rack with the supplied mounting rails:

a. Determine where to install the enclosure—Three holes are required for the rear posts and five

for the front.

b. For square holes, insert a cage nut into the top mounting hole of the front posts.

Insert Cage Nut

Front Rail Mount

Rear Rail Mount

Module 5

Module 3

Module 1

Module 2

Module 4

Module 6

SAS-3 RAID Controller 2

SAS-3 RAID Controller 1

CAUTION: Adding storage modules is a destructive process, because all of the capture and

indexing drive arrays must be recongured. Do not begin to add new storage to an existing

system until after you have backed up all capture and indexing data.

SAS-3 to SAS-3

SFF-8644 to

SFF-8644

SAS-2 to SAS-3

SFF-8088 to

SFF-8644

Diagram

Symbol

Diagram

Symbol

o When attaching a SAS-3 cable to the J5300, the

release pull-tab must be on the underside of the

plug. You should hear a distinct click when it is

seated properly.

o When attaching SAS-2 or SAS-3 cables to the head

unit, the release pull-tab should be on the top side of

the plug.

Unpack the Storage Module

o J5300 Storage Module

o Two AC Power Cords

o Two SFF-8644 to SFF-8644 cables

o Two SFF-8644 to SFF-8088 cables

o Adjustable rack-mounting rail assembly

o Lift/carry reminder insert

Quick Start Guide

(this document)

o Safety and regulatory compliance inserts

Prepare the Enclosure for Rack-Mounting

Prepare to Install the Rails

Identify the SAS Cables

Properly Orient the Connectors

Attach the Rail to the Rear Post

Connecting the J5300 to SAS-3 RAID Controllers

08a

Attach the Rail to the Front Post; Secure the Enclosure

Copyright © 2017 Symantc Corp. All rights reserved. Symantec, the Symantec Logo, the Checkmark Logo, Blue Coat, and the Blue Coat logo are trademarks or registered trademarks of Symantec Corp. or its affiliates in the U.S. and other countries. Other names may be trademarks of their respective owners. This document is provided for informational purposes only and is

not intended as advertising. All warranties relating to the information in this document, either express or implied, are disclaimed to the maximum extent allowed by law. The information in this document is subject to change without notice. Part Number: 231-03280 Rev E.0

THE DOCUMENTATION IS PROVIDED “AS IS” AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID.

SYMANTEC CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE FURNISHING, PERFORMANCE, OR USE OF THIS DOCUMENTATION. THE INFORMATION CONTAINED IN THIS DOCUMENTATION IS SUBJECT TO CHANGE WITHOUT NOTICE. SYMANTEC CORPORATION PRODUCTS, TECHNICAL SERVICES, AND ANY

OTHER TECHNICAL DATA REFERENCED IN THIS DOCUMENT ARE SUBJECT TO U.S. EXPORT CONTROL AND SANCTIONS LAWS, REGULATIONS AND REQUIREMENTS, AND MAY BE SUBJECT TO EXPORT OR IMPORT REGULATIONS IN OTHER COUNTRIES. YOU AGREE TO COMPLY STRICTLY WITH THESE LAWS, REGULATIONS AND REQUIREMENTS, AND ACKNOWLEDGE THAT

YOU HAVE THE RESPONSIBILITY TO OBTAIN ANY LICENSES, PERMITS OR OTHER APPROVALS THAT MAY BE REQUIRED IN ORDER TO EXPORT, RE-EXPORT, TRANSFER IN COUNTRY OR IMPORT AFTER DELIVERY TO YOU.

Page 2

Technical Support

o Contact Information—https://support.symantec.com/en_US/contact-support.html

o MySymantec—https://mysymantec.force.com/customer/s/

Documentation

o Go to https://support.symantec.com/en_US/Documentation.html and search for

"Security Analytics"

o Select Administration Guide or Hardware Guide for the document type.

When adding J5300 storage modules to an existing SAS-2 system keep the following in mind:

o Adding storage modules is a destructive process: Do not begin to add new storage until after

you have backed up all data.

o Contact Symantec support for assistance in calculating the new drive allocation.

231-03280 rev E.0

Module 5

Module 3

Module 1

Module 2

Module 4

Module 6

SAS-2 RAID Controller 1

SAS-2 RAID Controller 2

1 Controller Status

2 Internal Use Only

3 Not Used

4 SFF-8644 SAS Ports

5 Power Supply On/Off Switch

6 AC Power Indicator

7 Fault Indicator

8 Not Used

9 DC Power-Supply Status

10 Standby Power Indicator

1 AC Power Indicator

2 Global Enclosure Status

3 Controller 1 Activity

4 Controller 2 Activity

5 System Heartbeat

6 Drive Status

7 Drive Power/Activity

Existing

SAS-2 to

SAS-2

Cabling

Security Analytics appliances that have one RAID controller can support one storage

moduleonly. For SAS-2 RAID controllers, attach the storage module to the head unit using

SAS-2 to SAS-3cables.

SAS-2 RAID Controller SAS-3 RAID Controller

Integrating the J5300 with an Existing SAS-2 Environment

Module and Power-Supply Indicators

Front-Panel and Drive Indicators

Connecting a J5300 to a Single RAID Controller

08c

08b

If you are connecting only one storage module to a unit that has two RAID controllers, DO NOT

connect the module to both RAID controllers.

SAS-3 RAID ControllersSAS-2 RAID Controllers

Symantec J5300 40T Quick start guide

Symantec J5300 40T Quick start guide

Symantec J5300 40T Quick start guide

Other documents