Livex Lighting 7653-58 Operating instructions

Livex Lighting
Brand
Livex Lighting
Model
7653-58
Type
Operating instructions
ASSEMBLING
ASSEMBLING
ASSEMBLING
ASSEMBLING &
&
&
& INSTALLATION
INSTALLATION
INSTALLATION
INSTALLATION INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS PRODUCT#
PRODUCT#
PRODUCT#
PRODUCT#
7651
7651
7651
7651 7653
7653
7653
7653 7657
7657
7657
7657 7663
7663
7663
7663 OUTDOOR
OUTDOOR
OUTDOOR
OUTDOOR
WALL
WALL
WALL
WALL
MOUNT
MOUNT
MOUNT
MOUNT LIGHT
LIGHT
LIGHT
LIGHT FIXTURE
FIXTURE
FIXTURE
FIXTURE
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
MOUNTING
MOUNTING
MOUNTING
MOUNTING THE
THE
THE
THE FIXTURE
FIXTURE
FIXTURE
FIXTURE
Installation
Installation
Installation
Installation (see
(see
(see
(see fig.1)
fig.1)
fig.1)
fig.1)
1. Shut off the power at the circuit breaker and remove old fixture,
including the cross bar.
2. Carefully unpack new fixture and lay all the parts on a clear
surface. Take care not to lose any small parts necessary for
installation.
3. Attach the mounting screw part way into the side hole of the crook
cross bar , then lock it securely with hex nut until becoming . Attach
the cross bar to the junction box using two box screws . The side of
the cross bar marked “ GND ” must face out.
4. Follow wiring instructions carefully (see
(see
(see
(see fig.2)
fig.2)
fig.2)
fig.2)
5.
5.
5.
5. Attach the back plate of the lamp body(A) onto the junction box,
aligning screws on cross bar with mounting holes and lock it
securely with the ball nuts(B). Put the candle sleeve(D) over the
lamp holder.
6.
6.
6.
6. Install the light bulb s in accordance with the fixture
’
s
specifications. DO
DO
DO
DO NOT
NOT
NOT
NOT EXCEED
EXCEED
EXCEED
EXCEED THE
THE
THE
THE MAXIMUM
MAXIMUM
MAXIMUM
MAXIMUM
WATTAGE
WATTAGE
WATTAGE
WATTAGE RATING!
RATING!
RATING!
RATING!
7. Raise the finial(H) to the bottom hole of glass frame(F) and lock it
securely with the hex nut(G) until tight. Removing the cover on the
glass(E) sheet sponge, raise the glass(E) into the glass frame and
lock it securely with the clip. Attached glass frame(F) to bottom of
lamp body(A), lock it securely with the ball nut(C).
8. With
With
With
With silicone
silicone
silicone
silicone caulking
caulking
caulking
caulking compound
compound
compound
compound ,
,
,
, caulk
caulk
caulk
caulk completely
completely
completely
completely around
around
around
around
where
where
where
where back
back
back
back of
of
of
of cover
cover
cover
cover meets
meets
meets
meets with
with
with
with the
the
the
the wall
wall
wall
wall surface
surface
surface
surface to
to
to
to prevent
prevent
prevent
prevent
water
water
water
water from
from
from
from seeping
seeping
seeping
seeping into
into
into
into outlet
outlet
outlet
outlet box.
box.
box.
box.
Wiring
Wiring
Wiring
Wiring (see
(see
(see
(see fig.2)
fig.2)
fig.2)
fig.2)
1. Connect the electrical wires as follows. Connect the
black wire from the fixture to the black house (hot)
Wire. Connect the white wire from the fixture to the
white (neutral) house wire. Make sure all wire nuts are
secured.
You
may wrap the connections with electrical
tape.If your outlet box has a ground wire (green or bare
copper) connect fixture
’
s ground wire to it. Otherwise
attach the bare copper fixture wire to the green ground
screw on the cross bar.
2.Tuck the wire connections neatly into the wall junction
box.
F ig.1
Fig.2
White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
R
Listed
U
L
R
A
C
E
D
F
G
H
B
  • Page 1 1

Livex Lighting 7653-58 Operating instructions

Livex Lighting
Brand
Livex Lighting
Model
7653-58
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents