dB Technologies FLEXSYS F10 User manual

Category
Car audio amplifiers
Type
User manual
A.E.B. INDUSTRIALE s.r.l.
Via Brodolini, 8 - 40056 Crespellano (Bo) - ITALIA
Tel. + 39 051 969870 - Fax. + 39 051 969725
Internet: www.dbtechnologies.com
MANUALE D’USO
USER MANUAL
BEDIENUNGSANLEITUNG
CARACTERISTIQUES TECHNIQUES
Made in Italy
COD. 420120139 Rev.2
F315F315
F212F212
PROFESSIONAL ACTIVE SPEAKERS
digital power
RR
F8F8
F10F10
F12F12
F15F15
EnglishEnglishEnglish
user manualuser manual
12
user manualuser manual
EnglishEnglishEnglish
11
DESCRIPION
The speakers F8. F10, F12 and F15 of FLEXSYS series use cutting edge digital
®
amplifiers of the DIGIPRO series, providing with powers 200W and 400W to meet the
requirements of any kind of application.
These highly efficient amplifiers provide high power with limited weight and dimension.
Thanks to the low power dissipated, the cooling of the amplifier module does not require a
fan.
The digital preamplifier with DSP (Digital Signal Processing) controls the audio crossover
between the acoustic components, the frequency response, the limiter, and the acoustic
alignment. A selector enables to select one of two different equalizations - “FLAT” or
“PROCESSED“ - to provide high versatility for the different applications.
®
The amplifiers DIGIPRO 400W use power supplies featuring SMPS (Switched-Mode
Power Supplies) technology.
This technology increases power supply efficiency and minimizes its weight.
FLEXSYS F8
housing and
FLEXSYS F10
The F8 bi-amped active speaker is equipped with a
®
DIGIPRO amplifier delivering 150W RMS for the bass
section and 50W RMS for the high frequency section.
F8 active two-way speaker features woofer 8” (voice
coil 1,5”) and a neodymium compression driver 1”
(voice coil 1”) on a 90°/40°x 60° asymmetrical horn.
The speaker is made of 12mm ply wood, the one top
handle the 10 M8 threads located on the
sides and the back of the speaker are enabling easy
transport and installation.
The speaker has been designed to be used also as
stage monitor (40° angle), by rotating the horn you can
maintain the same audio coverage angle of high
frequencies also when the speaker is used as monitor.
In the bottom of the box there is a standard pole mount
cup (D36mm).
F10 bi-amped active speaker is equipped with a
®
DIGIPRO amplifier delivering 150W RMS for the bass
section and 50W RMS for the high frequency section.
F10 active two-way speaker features a woofer 10”
(voice coil 2”) and a neodymium compression driver 1”
(voice coil 1”) on a 90°/40°x 60° asymmetrical horn.
The speaker is made of 12mm plywood, the one top
plastic handle and the 12 M8 threads located on the
sides and the back of the speaker are enabling easy
transport and installation.
The speaker has been designed to be used also as
stage monitor (40° angle), by rotating the horn you can
maintain the same audio coverage angle of high
frequencies also when the speaker is used as monitor.
In the bottom of the box there is a standard pole mount
cup (D36mm).
FLEXSYS F8 - F10 - F12 - F15FLEXSYS F8 - F10 - F12 - F15
The F12 bi-amped active speaker is equipped with a
®
DIGIPRO amplifier delivering 300W RMS for the bass
section and 100W RMS for the high frequency
section.
F12 active two-way speaker features woofer 12”
(voice coil 1”) and compression driver 1” (voice coil
1,5”) on a 90°x40° CD- horn.
The speakers’ horizontal directivity is 90° by default
factory setting.
The speaker is made of 15mm birch plywood, the
three plastic handles the 12 M10 threads located
on the sides and the back of the speaker are enabling
easy transport and installation.
The speaker has been designed to be used also as
stage monitor (45° angle), by rotating the horn you can
maintain the same audio coverage angle of high
frequencies also when the speaker is used as
monitor.
In the bottom of the box there is a standard pole mount
cup (D36mm).
F15 bi-amped active speaker is equipped with a
®
DIGIPRO amplifier delivering 300W RMS for the bass
section and 100W RMS for the high frequency
section.
F15 active two-way speaker features a woofer 15”
(voice coil 2”) and a neodymium compression driver 1”
(voice coil 1,5”) on a 90°x40° CD- horn.
The speakers’ horizontal directivity is 90° by default
factory setting.
The speaker is made of 15mm birch plywood, the
three plastic handles and the 12 M10 threads located
on the sides and the back of the speaker are enabling
easy transport and installation.
The speaker has been designed to be used also as
stage monitor (45° angle), by rotating the horn you can
maintain the same audio coverage angle of high
frequencies also when the speaker is used as monitor.
In the bottom of the box there is a standard pole mount
cup (D36mm).
FLEXSYS F12
and
FLEXSYS F15
Handle
M8
M8
M8
M8
M8
Handle
M8
M8
M8
M8
M8
M8
Handle
Handle
Handle
M10
M10
M10
M10
M10
M10
F8
F10
F12-F15
FLEXSYS F8 - F10 - F12 - F15FLEXSYS F8 - F10 - F12 - F15
EnglishEnglishEnglish
user manualuser manual
14
user manualuser manual
EnglishEnglishEnglish
13
COMMANDS AND FUNCTIONS
AMPLIFIER PANEL
1) “Balenced Input” - “Link” - “Input Link” CONNECTORS
These balanced inputs can be used to connect balanced or unbalanced
microphones or audio sources at line level (0dB) (eg. preamplifier, mixer,
recorder, CD player, musical instrument, ...).
The balanced connector is connected in parallel and can be used to send the
audio signal to other amplified speakers, recorders or supplementary amplifiers.
2) “Ready” INDICATOR LIGHT
This indicator shows green to indicate that the main power voltage is correct.
The LED shows green normal operating conditions.
3) “Signal” INDICATOR LIGHT
This indicator shows green to indicate the presence of the audio signal (at a level of
-20dB).
4) “Limiter” INDICATOR LIGHT
This indicator shows red to indicate that the internal limiter circuit has tripped.
This prevents amplifier distortion and protects the speakers against overloads.
5) “Sensitivity” INPUT SENSITIVITY CONTROL
This control adjusts the sensitivity of the signal amplifier input.
This control does not affect the “Link” - “Input - Link” output level
6) MODE SWITCH
This two-way switch allows to choose between two different system presets.
The “Flat” position allows linear response of the speaker, which is mainly suitable
for the “live” application.
The “Processed” position emphasizes the low frequency and regulates the mid
frequency. It is suitable for music play back
7) “Input Sens” SWITCH
Position the switch in LINE to use a line level source (0 dB) or MIC to use a
microphone.
8) POWER CABLE SOCKET “MAINS”
Used for connecting the power cable supplied.
9) FUSE CARRIER “FUSE”
Mains fuse housing.
10) POWER SWITCH “POWER”
This switch can be used to switch the diffuser on and off.
REFERENCE DRAWINGS AT PAGES 49 and 50
CHARACTERISTICS AND PROTECTION
The speakers’s components in the box are protected by 1.2mm metal steel grille covered
by foam on backside.
Perform the checks listed below:
- Check if the speaker is properly connected to the power supply.
- Make sure that the power supply is of correct voltage.
- Check that the amplifier is not overheated.
- Disconnect the speaker from the mains power supply, wait for a few minutes and
connect it again.
If after these tests the red “LIMITER” LED is still on, please contact an authorised service
centre.
Front Grille
Cooling
Thermal control is provided by the internal microprocessor which, by means of two
sensors, controls the temperature of the amplifier and of the power supply, avoiding
overheating by limiting the overall volume.
In case of overheating (> 80 degrees) the volume decreases proportionally to the
temperature increase, making the change unnoticeable.
The correct volume and all the functions are automatically restored when standard
operating temperatures are reached.
Switch on
The amplifiers are equipped with a microprocessor to control the DSP and the amplifier.
The correct switch on of the amplifier is ensured by an initialization procedure; during this
test stage, the blue front LED flashes twice and the LEDs ( Limiter , Signal and Ready ),
located on the amplifier module, remain off for approx. 2 sec.
At the end of the switch on procedure, the front LED lights up (if enabled) and on the
amplifier module the Ready green LED only remains steadily on.
In case of severe failure of the speaker, the LED on the front panel flashes several times
and on the amplifier module, the Limiter red LED flashes and the speaker switches to
“mute”.
Failure indications and safeties
The microprocessor is able to signal three different kinds of failure by flashing the “Limter”
red LED on the amplifier panel before the lighting up of the “Ready” green LED. The three
types of failure are:
1) WARNING: a non severe error or auto-ripristinate malfunction is detected and the
performance of the speaker is not limited
2) LIMITATION: an error is detected and the performance of the speaker is limited (the
sound level is reduced by 3dB).
This does not affect the operation of the speaker since it continues to operate.
However, it is necessary to call the service centre to solve the issue.
3) FAILURE: a severe malfunction is detected. The speaker switches to “mute”.
Flashing Indication
1 or 2 Warning
3 or 4 Limitation
from 5 to 8 Failure
In case of failure, the “Ready” green LED remains off.
“”
“”
“”
FLEXSYS F8 - F10 - F12 - F15FLEXSYS F8 - F10 - F12 - F15
FLEXSYS F8 - F10 - F12 - F15FLEXSYS F8 - F10 - F12 - F15
EnglishEnglishEnglish
user manualuser manual
16
user manualuser manual
EnglishEnglishEnglish
15
DESCRIPTION
The FLEXSYS series bi-amped speakers are equipped with
®
DIGIPRO series class D amplifier. This high-efficiency
amplifier delivers high output power in a compact size at low
weight. Thanks to its high efficiency the cooling of the
amplifier module is obtained statically, thus avoiding the use
of a fan.
®
The power supply circuits of the DIGIPRO amplifier has
been conceived to work in full-range mode; thanks to the
SMPS (Switched-Mode Power Supply) technology with PFC
(Power Factor Correction) the operation with supply voltages
between 100 Vac and 240Vac is guaranteed by ensuring the
same sound performances even with floating and non-
stabilized power supply systems.
FLEXSYS F212 (2 ways)
The F212 bi-amped active speaker is equipped with a
®
DIGIPRO amplifier which delivers 500W RMS for the bass
section and 250W RMS for the high frequency section.
The F212 active two-way speaker features two 12” (voice coil
2.5”) woofers and a neodymium 1”(voice coil 1.75”)
compression driver. The phase plug attached to the front of
the upper 12” woofer avoids the vertical phase modulation
which usually take place in this type of configuration and
ensures a precise horizontal coverage of the medium
frequencies.
The speaker is made of 15mm birch ply wood, the 4 handles,
the 12 M10 threads located on the sides and the back of the
speaker are enabling easy transport and installation.
The trapezoidal-shaped housing (20° angle) allows the side-
by-side setup of several speakers in cluster configuration. For
side-by-side installation, the horn must be turned (40° x 60°)!
The bottom features a adjustable foot (in height) to inclinate
the tilt angle up to a max. of 5°. This allows to direct the sound
radiation without using additional supports.
In the bottom of the box there is a standard pole mount cup
(D36mm) made of aluminium
FLEXSYS F315 (3 ways)
®
The F315 active speaker is equipped with a DIGIPRO
amplifier delivering 500W RMS for the bass section featuring
a 15” woofer (voice coil 3”) and 500W RMS for the mid-high
section featuring a passive filter driving a 6” midrange (voice
coil 2”) and a 1” compression driver (voice coil 1.5”).
The speaker is made of 15mm birch ply wood, the 4 handles,
the 12 M10 threads located on the sides and the back of the
speaker are enabling easy transport and installation
The 15” woofer and the midh-high section with horizontal 90°
coverage is the ideal solution for all demanding full-range
applications .
In the bottom of the box there is a standard pole mount cup
(D36mm) made of aluminium
FLEXSYS F212 - F315FLEXSYS F212 - F315
CONTROLS AND FUNCTIONS
1) " BALANCED INPUT” INPUT CONNECTOR
Balanced input at line level. Accepts “XLR” sockets.
2) "BALANCED LINK/OUT ” OUTPUT CONNECTOR
The “XLR” connector connected in parallel with input (1) can be used to send the
input audio signal to another active speaker.
3) “LIMITER” INDICATOR LIGHT
This indicator shows red to indicate that the internal limiter circuit has tripped.
This prevents amplifier distortion and protects the speakers against overloads.
4) “SIGNAL” INDICATOR LIGHT
This indicator showscomes on green to indicate the presence of the audio signal (at
a level of -20dB).
5) “MUTE” INDICATOR LIGHT
This yellow indicator indicates amplifier status.
The LED is off in normal operating conditions.
6) “READY” INDICATOR LIGHT
This indicator shows green to indicate that the main power voltage is correct.
The LED shows green in normal operating conditions
7) “INPUT SENS” INPUT SENSITIVITY CONTROL
This control adjusts the sensitivity of the signal amplifier input.
This control does not affect the “BALANCED LINK/OUT” output level
FLEXSYS F212
8) "MODE" SWITCH
This two-way switch allow to choose between two different system presets.
The “SINGLE SPEAKER” position allows linear response when one single speaker
is used.
The “CLUSTERED SPEAKER” position reduces the medium-bass frequencies
which are coupling by the side-by-side attachment of several speakers.
9) "MAINS INPUT" POWER SOCKET
For connecting the power cable provided.
The connector used for mains connection is a POWER CON® (blue) socket
10) “MAINS OUTPUT LINK” POWER SOCKET
For linking the mains power. The output is connected in parallel with input (9) and
can be used to power another active speaker.
The connector is a POWER CON® (grey) socket
11) "MAINS FUSE" FUSE CARRIER
Mains fuse housing.
FLEXSYS F315
8) "MODE" SWITCH
This two-way switch allows to choose between two different system presets.
The “FLAT” position allows linear response of the speaker, which is mainly suitable
for the “live” application in closed rooms.
The “PROCESSED” position increases the low frequencies and it is suitable for
music play back or for the use in open air applications.
9) POWER CABLE SOCKET “MAINS INPUT”
Used for connecting the power cable supplied.
10) FUSE CARRIER “MAINS FUSE”
Mains fuse housing.
11) POWER SWITCH “POWER”
Switches the active speaker on and off.
REFERENCE DRAWINGS AT PAGES 51 and 52
FLEXSYS F212 - F315FLEXSYS F212 - F315
EnglishEnglishEnglish
user manualuser manual
18
user manualuser manual
EnglishEnglishEnglish
17
CHARACTERISTICS
Front Grille
The speakers’s components in the buffle are protected by 1.5mm metal steel grille
covered by foam on backside.
Cooling
The amplifier is cooled by means of the aluminium panel placed on the back of the
speaker.
The thermal protection is ensured by an internal circuit which controls the temperature of
the amplifier and protects this against any risk of overheating thus limiting the general
volume ( temperature >80°C).
If the temperature reaches the maximum operating temperature (>80°C), the audio signal
is set to the “MUTE” position and it will be indicated by the switching on of the yellow
“MUTE” LED.
The requiriered volume and all functions will be restored automatically when the normal
operating temperatures are reached.
Protection
When the yellow “MUTE” LED turns on, it means that a malfunction has been detected on
the speaker, thus setting this to the mute position.
Perform the checks listed below:
- Check if the speaker is properly connected to the power supply.
- Make sure that the power supply is of correct voltage.
- Check that the amplifier is not overheated.
- Disconnect the speaker from the mains power supply, wait for a few minutes and
connect it again.
If after these tests the yellow “MUTE” LED is still on, please contact an authorised service
centre.
CONNECTIONS (Only for FLEXSYS F212)
Connecting to the mains supply
Each active speaker features its own power cable. Connection is done by a Neutrik
POWER CON® (blue) model which permits easy and fast connection to the speaker as
well as being an excellent locking system.
The same connector serves as a switch to turn ON and OFF the active loudspeaker by
turning the connector to the left (OFF) or right (ON).
The active speaker must be connected to a power supply able to deliver the maximum
required power.
Main power supply linking
On the rear of the speaker, a Neutrik POWER CON® connector (grey) offers linking the
mains power supply.
This socket links the power supply to another speaker, thereby reducing the direct
connections to the mains. Maximum amplifier input power is shown on the amplifier
panel.
The maximum number of speakers connected together varies of max input power and
of the maximum allowed current of the first power socket.
WARNING
Never use the handles to hang the speaker!
EXACT!
WRONG! EXACT!
ROTATING HORN (Except FLEXSYS F315)
Loudspeaker allows to maintain the same coverage angle by featuring a rotating horn.
The speakers are always supplied by the manufacturer with the horn positioned horizontal
by default at 90° for Flexsys F8, F10, F12 and F15 and 60° by default for F212.
Only Flexsys F212 can be used placing more speakers side by side (cluster), in this case is
necessary rotate the horn.
If you wish to change the coverage angle (Fig. 5):
- unscrew the fixing screws of the grille
- remove the front protective grille by slightly pressing on one side and taking the grille
off the recessed slots
- unscrew the fixing screws of the horn
- rotate the horn in the desired position (the horn should never be removed from the
driver!)
- tighten the fixing screws of the horn
- put the grille back in the recessed slots and tighten the screws of the grille.
LOUDSPEAKER INSTALLATION
WARNING
Make sure that the loudspeaker is securely installed in a stable position to avoid any
injuries or damages to persons or property.
For safety reasons do not place one loudspeaker on top of another without proper fastening
systems. Before hanging the loudspeaker check all the components for damages,
deformations, missing or damaged parts that may compromise safety during installation.
If you use the loudspeakers outdoors avoid places that are exposed to bad weather.
The loudspeaker has the following mounting options:
- bookshelf (Fig. 1)
- floor (monitor) (Fig.2)
- on speaker stands (Fig.3)
- suspended with support rails or brackets supplied by the manufacturer (Fig.4)
WARNING
To hang the loudspeaker use only one eyebolt for each hanging point
The hanging points are of M8 threads for Flexsys F8,F10 and M10 threads for
Flexsys F12, F15, F212 and F315.
Do not unscrew both bolts recessed in the housing!
FLEXSYS F8 - F10 - F12 - F15 - F212 - F315FLEXSYS F8 - F10 - F12 - F15 - F212 - F315
FLEXSYS F212 - F315FLEXSYS F212 - F315
EMI CLASSIFICATION
According to the standards EN 55103 this equipment is designed and suitable to operate in
E3 (or lower E2, E1) Electromagnetic environments.
EnglishEnglishEnglish
user manualuser manual
20
user manualuser manual
EnglishEnglishEnglish
19
TECHNICAL SPECIFICATIONS
System Active Bi-Amp Active Bi-Amp Active Bi-Amp
Type of amplifier Class D Class D Class D
RMS power
Frequency response
5-20000Hz (-10dB) 70-20000Hz (-10dB) 65-20000Hz (-10dB)
0Hz , 24dB/oct 2050Hz , 24dB/oct 1800Hz, 24dB/oct
Sound pressure (max SPL)
-3dBu Max -3dBu Max -3dBu Max
2K2ohm/20Kohm (MIC/LINE) 2K2ohm/20Kohm (MIC/LINE) 2K2ohm/20Kohm(MIC/LINE)
Integrated tilt unit
FLEXSYS F8 FLEXSYS F10 FLEXSYS F12
150W + 50W 150W + 50W 300W +100W
90-19000Hz (+/-3dB) 80-19000Hz (+/-3dB) 75-19000Hz (+/-3dB)
7
Crossover 205
121dB 125dB 127dB
Components 1x8” woofer - 1.5” voice coil 1x10” woofer - 2” voice coil 1x12” woofer - 2” voice coil
1x1” compression driver - 1” voice coil 1x1” compression driver - 1” voice coil 1x1” compression driver - 1.5” voice coil
Neodimium Neodimium
Dispersion 90°/40°x60° Asymmetrical 90°/40°x60° Asymmetrical 90°x40°
Input sensitivity
Input impedance
Power supply 110-120Vac 50-60Hz 110-120Vac 50-60Hz 110-120Vac 50-60Hz
220-240Vac 50-60Hz 220-240Vac 50-60Hz 220-240Vac 50-60Hz
Housing shape Trapezioidal Trapezioidal Trapezioidal
Colour Black Black Black
Dimensions (WxHxD) 260x420x260mm 300x480x300mm 360x610x360mm
Weight 9,5Kg 12Kg 16,5Kg
Flying support 10 x M8 12 x M8 12 x M10
Pole mount cup D36mm D36mm D36mm
Handle --- ---- 2 (one per side)
1 top side,niche 1 top side 1 top side
--- --- ---
Rotating horn Yes Yes Yes
No No No
TECHNICAL SPECIFICATIONS
System Active Bi-Amp Active Bi-Amp Active Bi-Amp
Type of amplifier Class D Class D Class D
RMS power
Frequency response
55-20000Hz (-10dB) 50-20000Hz (-10dB)
1800Hz, 24dB/oct 1800Hz - 24dB/oct
Sound pressure (max SPL)
-3dBu Max
2K2ohm/20Kohm (MIC/LINE)
FLEXSYS F15 FLEXSYS F212 FLEXSYS F315
300W + 100W 500W +2 50W 500w + 500W
60-19000Hz (+/-3dB) 65-19000Hz (+/-3dB) 60-19000Hz (-3dB)
47-20000Hz (-10dB)
Crossover 750Hz - 24dB/oct
2000Hz - 18dB/oct passive
128dB 132dB 131dB
Components 1x15” woofer - 2” voice coil 2x12” woofer - 2,5” voice coil 1x15” woofer - 3” voice coil
1x1” compression driver - 1.5” voice coil 1x1” compression driver - 1,75” voice coil 1x6.5” midrange - 2” voice coil
1x1”compression driver - 1,5” voice coil
Dispersion 90°x40° 60°x40° 90°x40°
Input sensitivity -3dBu Max -3dBu Max
Input impedance Balanced 20Kohm Balanced 20Kohm
Unbalanced 10Kohm Unbalanced 10Kohm
Power supply 110-120Vac 50-60Hz Full-range with PFC Full-range with PFC
220-240Vac 50-60Hz 100-240Vac 50-60Hz 100-240Vac 50-60Hz
Housing shape Trapezioidal Trapezioidal Trapezioidal
Colour Black Black Black
Dimensions (WxHxD) 430x680x430mm 300x480x300mm 440x880x500mm
Weight 20Kg 31,5Kg 31 Kg
Flying support 12 x M10 12 x M10 12 x M10
Pole mount cup D36mm D36mm D36mm
Handle 2 (one per side) 2 (one per side) 2 (one per side)
1 top side 1 top side 1 top side
---------- 1 back side,niche 1 back side,niche
Rotating horn Yes Yes No
Integrated tilt unit No Yes No
DeutschDeutschDeutsch
BedienungsanleitungBedienungsanleitung
29
DeutschDeutschDeutsch
BedienungsanleitungBedienungsanleitung
30
T C
HN
I
SC
HE
D
AT N
E E
F EX YS
8 F
L
X
S S
F
0 FLE SY
S
12L
S F
E Y
1 X
F
Sy
s e
t m
t
i
v
Bi
-
A
k
i
v Bi
A
mp
tiv Bi
-
A
k
A
mp
t -
A
k A
mp
V
e s
t
rk
r
y
p
r ä e
t C
as
D
l
a
s
s
C
s
D
l
s
C
D l
a s
M
S
i
t
gR
Le s
un
1 0 +
5 W
15 W
+
50 300 +
1
0
W
5 W
0 0
W
W 0
F
re
ue
n
ga
90
0 5 1
9
00 H
(+
/
-
3
B)q
z
n
g
-
1
0 0
H
z (
-
d )
8 1
9
0 H
(+
/-
3
B)
9
0 +
/
3
B - 0 0 z d
7 - 0 z
d
5
20
0
0
Hz
-
1
0d 7
-
00
0
0
z
( 1
0
dB)
65
2
000
H
z
- 0
d
B
7
-
0
( B) 0
2 H
-
-
0 ( 1
)
r
s
o
v
r
C os
e 2
5
00
10Hz 0H
z
4B/o
t
25
z
, 2
d
B/ct 8
0
,
4
B
/
ot
0
,2
d
c H 4 o
2d c
Sc
h
l
l ruck
m
a
S
P
L
)
a d
( x
1
2
1
d 1
25
B 1
2
d
B d
7 B
La
tspr
ch
ru
e e
x
wo
f r
1 5”
v
o
e
c
o
il 1
1
wo
o
f r
2
v
oi
ce
o
1x
12
w
o
e - 2” v ic c
o
il
1
8
o
e - . i
c
x
0
e - c il
o
f
r o e
1x
1”
c
m
p
es
s n r e
-
1
v
i
c
coi
l 1
x
o r
s io d i
v r
1”
v
o
c
e
o
il 1x1”
c mp
e si n d
r e
- 1.
5
v
i
c
e
co l
o r io
d i
v
r
o
e
1 c mp
e s n r e
- i
c o r
s o iv r
o
i
Ne
o y i
m
e
d mi
u
d m u
N o
y m
A
tr hlch
a
ra
kte i
ti
k
bs
a
r s
9
0°/
4
0°x 0
a
s
y
tri
s
c
h 9
0
°/
0
° 6 °
as
y
m
m
e r c
h 0
°x4 °6 °
m
m
e 4
x 0 t i
s 9
0
E
mp
i
dl
ch k i
Eingaf
n
i
e t n
g 3 B
u x
-3
d
M
a -
3 Bu x
-
d M
a Bu
x
d M
a
m
pe
nz
ng
ng
I
d
a
Ei a
2K2
h 20
Ko
m
(
C/ IN
E)
K2
o
m/2
0K
h
(
M
IC L NE)
2
2o
h
2
0
K
o m
(
C
/ I
E
)
o
m/
h
MI L
2
h
o m
/ I K
m/ h MI L N
N
et
zspan
ngnu
11
0-
2 V c 50
-6
H 110
-
1
0 a
5
0- 0
z
1
0- 2
V c 5
0
-6 H
1
0 a
0
z
2
V c 6
H
1 1
0
a
0
z
2
0
-2
0
a
50
-
0 z 2
0
- 4
V
c
5
0-
6 H 2
0-
2 0
a
0
-6
0 z
2
4
V
c
6 H 2
2 0
a
0 z 2 4 V
c
5 H
L
a
uf
s
pr
e h
e
o
rm
c r
f
Tra e
z
f
ö
r Tr p z
ör
mi
g T
r
a e
f
ö
r i
p
mi
g a e
f
p z
m g
a
r
b
F e
S
c w r h a z
Sch
wa
r
h a z
S
c w r z
A ss
u
n
ge
(B
x
H
x
T
bm
e n
)
6
0
x
4
20
26
0
3
00
x48
0x
300
m
m 6
0x
10
x 60m
m
2
x
m
m 3 6
3
G
w
i
ce h
t 9
,
5Kg
12
Kg
1
6
5
Kg,
u ö ich e
it nFl
gm
g
l
k
e
1
x
8
2
1
x
M1
0
M 1
x
M8 2
0
S
t n
der
fl
a
c
ä
n
s h
D
3
6mm
D
6
m
m D
3 m
m
3
6
G
f
f
e
r
i --
-
-- 2
x
e e
p o
it
-
- in r r S
e e
1
x
Deck l
1
x
e
c
ke 1x
De
ck
l e D l e
--
-
-
-
- -
-
-
D
hb
a
re
s
H
r
n
r
e o
JaJ a
a
J
S
c
ä
g
s
te
l
eh
r l
r
e Ne
in
N
e
N in
S
CHE
TEN
T
E
CHN
I D
A
5
12 F
1
5
FLEXS
Y
S
F1
F
L
E
X
S
Y
S F
2
L
E
X
SYS
F
3
s
m
k
A
m Ak
Am
A
k Am
S
y t
e
A t
iv
Bi
- p ti
v Bi
- p
tiv
B
i-
p
e
s
ä
k
ry ss
D
C s
D
C
s D
Vr
tre t
p
Cl
a l
as
la
s
L
i
un
0 1
0 50
0
5
0 5
0
R
MS
e st
g 3
0 W
+
0 W
0
W +
2
5 W
0
w
+
0 W
r
e
ung
n 0
9
0H
z
( 3
B)
6-
9
z 3B
6-
9
0
-
dF
qe
z
ag
6
-
1
0 0
+
/-
d
5 1 0
0
0H
(
+
/
-
d ) 0
1
00
Hz
( 3
B)
-
0
0 z 0
B)
5-
0
z
-
0
B)
4
-0 0 -0B
)
55
2
0
0H
(
-
1d
0
2
00
0
H(1
d 720
0
Hz(
1d
r
o
s er 8
H , 2 o
1
8 H
dB
/ t
75
2 B
o
tC so
v
1
00 z
4d
B
/ c
t 00
z
-
24 o
c
0
H
z
- 4d
/ c
0 H
z
- d
c a
2
0 0
18
B/
o t
p s
siv
l
d
ruck
( a
S
P 1
2 B
13 B 1
3
B
S
cha
l
m x L
) 8d
2
d
1d
a
sr
e
r
1
1 o
e-”
o c
2 2
o
r-,
i
ceo 1 5 o
r
o
cL
ut
p
che
x 5”
w
o f
r
2
v i
ce oil
x1
” wo
fe
2
5
vo
c i
l x
1
” w
o f
e
- 3 v
ic
e
o
il
1 1
co p e i
o d
i
ve -
1 c
c
1
” co
p
e
io
d
i
e - 5
vo
i
l 1
. i
d a g
- 2
vo
i
l
x
m
r
s
s
n
r
r
.5 v
o
i e
o
il
x
1
m
r ss n r v
r
1
,
7
i
ce co x6 5”
m
r n e
i
ce co
1
o
p
n r r
- ,
5 ic
e o
x
1
c
m
re
ssio
d iv
e
1
vo c il
ra l
c k r
is i
0 6
° 0
0Ab
st
h h
a
ra t
e t k
0
x
4 °
0x4 °
0x
4
°
n h
k
t Ei
g
n -d
-Bu
a
-B
ua
Em
p
f
i
d
li
c ei
n a g
3 B
u M
a
x
3
d M x
3d M
x
e
ag
2
o
0 h
MIC
IN
)
Sy
m r
h 2 K
o m
S
m r
2
KoIm
p
da
n
z Ei
n
g
n
K2
hm/2
Ko
m (
/L E
me
t is
c 0
h
y met i
sch
0 hm
U
y
m tr
h 1
Ko
U ym r
h Ko
m
n
s
me
i
sc 0 hm n
s met i
sc 1
0 h
t
p
a u 101 Va
5-
0
F l
-a
g h
PF
F
ll
-a
g h
P
F
N
e
z
s
nn
n
g
1 -
2
0 c
0 6 H
z
u
l r
n
e w
i
t
C u r n e
wi
t C
20
2
V
a
5
-0 1
02 Va 5-0 10
2
Va
5-
2
-40
c
06Hz 0-
4
0
c
06H
z 0-
4
0 c
0
6
0
Hz
afp c
ef m T z r i
g T
p
z r ig
T
p z
f
r
igLu
s
r
eh
r
or
r
a
p
e
m
ra
e f
ö m ra e
ö
m
ab
e
Sc
a
S
ch S
ch
rFr
h
w rz
w
a
rz w
a z
e
sn n
(Hx
40
8x
4
0 m
30
8
x30
m
4
0 8
5
0 m
A
b
m
s u
g
e
Bx
T) 3
x
60
3m
0
x40
0
m 4x
8
0x
0
m
w
c t
2K
g 3,
5
3
G
e
i
h 0 1
K
g 1
K
g
l g g
li
e e
1
x
M
0 1
1
1F
u
m
ö
ch
k i
t n 2 1
2
xM
1
0
2
x
M 0
ä
drf
n
c D
m Dm D3 mS
tne
l
ash
3
6
m
3
6 m 6 m
f
2
i
n
p
S
e
2 i
p S
e
2 x e
e r it
e
G
rif
e x e
e
r
ro
it
e x
e
n
e
r ro i
te
i
n r
p
o
S
e
1 c
l
1 ck 1
ckx
D
e
k
e x
De
el
x D
e e
l
-
-
- -
- 1
ck
it
e 1 c
k
it
e- -
- -
- x R
ü s
e
x
R
ü
se
e
a
e
o JJ
NeDr
h
br
sH
r
n
a
a
i
n
äs
e
e N J
a
N
eSc
h
r g t l
l
r e
in
i
42
41
FLEXSYS F12
FLEXSYS F15
FLEXSYS F12
FLEXSYS F15
Made in Italy
220-240V~ 50-60Hz
110-120V~ 50-60Hz
(T A 250V~)
(T A 250V~)
Internal voltage setup
MODULE POWER
CONSUMPTION
W MAX
“CAUTION”
TO PREVENT ELECTRICAL SHOCK
DO NOT REMOVE COVER
“AVIS”
RISQUE DE CHOCH ELECTRIQUE
NE PAS OUVRIR
FUSE MAINS
POWER
PUSH
00
II
MODE
READY
SIGNAL
LIMITER
8
0dB
+4dB
-3dB
FLAT
PROCESSED
BALANCED
INPUTS
LINK
INPUT / LINK
SENSITIVITY
digital power
MIC
INPUT
SENS
LINE
1
7
6
5
4
3
2
10
8
9
F
DIGITAL ACTIVE SPEAKER
FLEXSYS F8
FLEXSYS F10
FLEXSYS F8
FLEXSYS F10
MODE
READY
SIGNAL
LIMITER
8
0dB
+4dB
-3dB
FLAT
PROCESSED
digital powerdigital power
RR
DIGITAL ACTIVE SPEAKER
INPUT
SENS
INPUT / LINK
LINK
BALANCED
INPUT
SENSITIVITY
LINE
MIC
ON
SERIAL NUMBER REVISION
“CAUTION”
TO PREVENT ELECTRICAL SHOCK
DO NOT REMOVE COVER
“AVIS”
RISQUE DE CHOCH ELECTRIQUE
NE PAS OUVRIR
FF
FUSE
MAINS
POWER
MODULE POWER
CONSUMPTION
250W MAX
MODEL
Made in Italy
220-240V~ 50-60Hz
110-120V~ 50-60Hz
(T1A 250V~)
(T2A 250V~)
Internal voltage setup
PUSHPUSH
OO
II
7
6
5
4
3
2
1
10
8
9
Contattare dB Technologies per gli accessori da utilizzare a corredo.
Si declina ogni responsabilità da un utilizzo inappropriato degli accessori o di dispositivi aggiuntivi non idonei allo
scopo.
Contact dB Technologies for accessories to be used with speakers.
Will not accept any responsibilty when inappropriate accessories or not suitable additional devices are used.
Kontaktieren sie dBTechnologies für passendes Lautsprecherzubehör.
Falls unpassendes Zubehör verwendet wird, wird jegliche Haftung ausgeschlossen.
Contact dBTechnologies pour les accessoires à utiliser avec la machine.
N'accepterons pas toutes les responsabilités lorsque des accessoires inappropriés ou ne conviennent pas à des
dispositifs supplémentaires sont utilisés.
ISTRUZIONI DI SICUREZZA PER ACCESSORI /
ZUBEHÖR NSTRUCTIONS DE SÉCURITÉ
SAFETY INSTRUCTIONS FOR ACCESSORIES
SICHERHEITSHINWEISE / I POUR LES ACCESSOIRES
READY
MUTE
SIGNAL
LIMITER
SENSITIVITY
0dB
88
+4dB
MODE
-3dB
BALANCED
INPUT
LINK
OUT
PUSH
2
1
8
7
6
5
4
3
FLEXSYS F315FLEXSYS F315
MAINS LINK
ACTIVE P.F.C.
MAINS
FUSE
FULL RANGE MAINS INPUT
100-240V~ 50-60Hz
1000W MAX
OUTPUT
220-240V~ MAX 15A
100-120V~ MAX 10A
220-240V~ (T5A 250V)
100-120V~ (T10A 250V)
“CAUTION”
TO PREVENT ELECTRICAL SHOCK
DO NOT REMOVE COVER
“AVIS”
RISQUE DE CHOCH ELECTRIQUE
NE PAS OUVRIR
READY
MUTE
SIGNAL
LIMITER
SENSITIVITY
0dB
88
+4dB
MODE
-3dB
BALANCED
INPUT
LINK
OUT
PUSH
2
1
8
7
6
5
4
3
9
11
10
FLEXSYS F212FLEXSYS F212
FULL RANGE MAINS INPUT
100-240V~ 50-60Hz
1000W MAX
220-240V~ (T5A 250V)
100-120V~ (T10A 250V)
POWER
ON
OFF
“CAUTION”
TO PREVENT ELECTRICAL SHOCK
DO NOT REMOVE COVER
“AVIS”
RISQUE DE CHOCH ELECTRIQUE
NE PAS OUVRIR
FUSE MAINS
MAINS FUSE
9
11
10
DIGITAL ACTIVE SPEAKER
FLAT
PROCESSED
digital power
RR
F315
DIGITAL ACTIVE SPEAKER
SINGLE SPEAKER
CLUSETRED SPEAKER
digital power
RR
F212
44
43
Fig. 3
SUPPORTO PIANTANA STANDARD (D36mm)
STANDARD STAND (D36mm)
STANDARD-HOCHSTÄNDER (D36mm)
SUPPORT STANDARD (D36mm)
UTILIZZO IN APPOGGIO
SUPPORTED USE
ANWENDUNG
UTILISATION EN APPUI
Fig. 1
APPENDIBILITA TRAMITE GOLFARI
SUSPENDABLE WITH EYEBOLTS
MAN KANN DEN LAUTSPRECHER MIT RINGSCHRAUBEN HANGEN
POSSIBILITÉ DE SUSPENSION AVEC ANNEAUX
Fig. 4
46
45
UTILIZZO A PAVIMENTO (MONITOR)
FLOOR USE (MONITOR)
VERWENDUNG AUF DEM BODEN (MONITOR)
UTILISATION AU SOL (ÉCRAN)
SOLO FLEXSYS F8, F10, F12, F15
ONLY FLEXSYS F8, F10, F12, F15
NUR FLEXSYS F8, F10, F12, F15
SEULEMENT FLEXSYS F8, F10, F12, F15
Fig. 2
Opzione codice/Optional code/Optionales Zubehör:
TE M8 per/for/für FLEXSYS F8, F10
TE M10 per/for/für FLEXSYS F12, F15, F212, F315
I codici includono solo i golfari.
The code including eyebolts only/ Artikel enthält nur Ringschrauben.
47
48
ANGOLO DI COPERTURA TROMBA / HORN ANGLE COVERED
HOCHTONHORN ABSTRAHLWINKEL / ANGLE DE COUVERTURE COTE
FLEXSYS F8
FLEXSYS F10
60°
40°
90°
40°
90°
60°
40°
90°
ANGOLO DI COPERTURA TROMBA / HORN ANGLE COVERED
HOCHTONHORN ABSTRAHLWINKEL / ANGLE DE COUVERTURE COTE
90°
40°
FLEXSYS F12
FLEXSYS F15
Utilizzo a pavimento (monitor) con tromba ruotata
Floor use (monitor) with rotated horn.
Verwendung auf dem Boden (monitor) mit gedrehtem Horn.
Utilisation au sol (écran) avec cone tourné
60°
90°
40°
Utilizzo a pavimento (monitor) con tromba ruotata
Floor use (monitor) with rotated horn.
Verwendung auf dem Boden (monitor) mit gedrehtem Horn.
Utilisation au sol (écran) avec cone tourné
40°
90°
Fig. 5 Fig. 5
ANGOLO DI COPERTURA TROMBA / HORN ANGLE COVERED
HOCHTONHORN ABSTRAHLWINKEL / ANGLE DE COUVERTURE COTE
60°
40°
FLEXSYS F315
60°
40°
90°
40°
Con tromba ruotata
With rotated horn.
Mit gedrehtem Horn.
Avec cone tourné
Fig. 5
60°
40°
FLEXSYS F212
50
49
ANGOLO DI DISPERSIONE -6dB
DISPERSION ANGLE -6dB
ABSTRAHLWINKEL -6dB
ANGLE DE DISPERSION -6dB
60°
40°
60°
80°
Diffusore singolo
Single speaker
Einzelner Lautsprecher
Enceintes séparées
Diffusore affiancato
Speaker side by side
Nebeneinander angeordnete Lautsprecher
Enceintes accolées
Per utilizzo affiancate occorre ruotare le trombe
For side-by-side installation turn the horns
Um eine Cluster-Aufstellung (80°) vorzunehmen, muss das Horn gedreht werden
Pour le montage des côtés, il faut tourner le cornets
SOLO FLEXSYS F212
ONLY FLEXSYS F212
NUR FLEXSYS F212
SEULEMENT FLEXSYS F212
52
51
DIMENSIONI
DIMENSIONS
ABMESSUNGEN
DIMENSIONS
FLEXSYS F10FLEXSYS F8
300300
483483
300300
260260
420420
260260
Piede regolabile (inclinazione 5° max)
Adjustable foot (max 5° inclination)
Verstellbare Stütze (Neigung max. 5°)
Vérin réglable (inclinaison 5° max.)
UTILIZZO IN APPOGGIO
SUPPORTED USE
ANWENDUNG
UTILISATION EN APPUI
SOLO FLEXSYS F212
ONLY FLEXSYS F212
NUR FLEXSYS F212
SEULEMENT FLEXSYS F212
Anello
Gambo
Punta = Positivo/Caldo/Fase +VE
Anello = Negativo/Freddo/Fase -VE
Punta
Gambo
Punta = Segnale
Gambo=Schemo/Massa/Terra
Funzionamento sbilanciato con
connettore jack 1/4” (6,3mm)
1
2
3
Ingresso
XLR - maschio
Pin 3 =Negativo/Freddo/Fase -VE
1
2
3
Funzionamento sbilanciato con
connettore XLR
Ingresso
XLR - maschio
Pin 2 = Positivo/Caldo/Fase +VE
Pin 1 =Schermo/Terra/Massa
Pin 3 = Connesso al Pin 1
Funzionamento bilanciato con
connettore jack 1/4” (6,3mm)
Gambo=Schemo/Massa/Terra
Punta
Funzionamento bilanciato con
connettore XLR
Pin 2 = Positivo/Caldo/Fase +VE
Pin 1 =Schermo/Terra/Massa
Tip = Positive/Hot/+VE Phase
Balanced use of stereo 1/4” jack plug
Tip
Sleeve
Tip = Signal
Sleeve=Screen/Ground/Earth
Unbalanced use of stereo 1/4” jack plug
Balanced use with XLR connectors
Input
XLR - male
Pin 2 = Positive/Hot/+VE Phase
Pin 3 =Negative/Cold/-VE Phase
Pin 1 =Screen/Ground/Earth
Unbalanced use with XLR connectors
Input
XLR - male
Pin 2 = Positive/Hot/+VE Phase
Pin 1 =Screen/Ground/Earth
Pin 3 = Link to Pin 1
Ring=Negative/Cold/-VE Phase
Sleeve=Screen/Ground/Earth
Sleeve
Ring
Tip
COLLEGAMENTI
CONNECTIONS
ANSCHL
BRANCHEMENTS
ÜSSE
40°
40°
SCHEMA A BLOCCHI
BLOCK DIAGRAM
BLOCKSCHALTBILD
SCHEMAS FONCTIONNELS
WOOFER 12”
WOOFER 12”
READYLIMITER
BALANCED
MAIN INPUT
LINK
Switching Mode
Power Supply
PFC
Power Factor
Correction
SMPS
SIGNAL
SENSITIVITY
MICROPROCESSOR
Class D
®
DIGIPRO
1000W
DSP
Digital Signal Processing
MICROPROCESSOR
MUTE
PASSIVE
FILTER
MIDRANGE 6.5”
COMPRESSION
DRIVER 1”
Class D
WOOFER 15”
MODE
READYLIMITER
BALANCED
MAIN INPUT
LINK
L
N
FULL RANGE
MAINS INPUT
Switching Mode
Power Supply
PFC
Power Factor
Correction
SMPS
MAINS
FUSE
L
N
MAINS OUTPUT
LINK
SIGNAL
SENSITIVITY
MICROPROCESSOR
Class D
®
DIGIPRO
1000W
DSP
Digital Signal Processing
MICROPROCESSOR
MUTE
COMPRESSION
DRIVER 1”
Class D
MODE
FLEXSYS F315
FLEXSYS F212
L
N
MAINS
FUSE
POWER
SWITCH
56
55
SCHEMA A BLOCCHI
BLOCK DIAGRAM
BLOCKSCHALTBILD
SCHEMAS FONCTIONNELS
READYLIMITER
Switching Mode
Power Supply
SMPS
SIGNAL
SENSITIVITY
Class D
®
DIGIPRO
DSP
Digital Signal Processing
MICROPROCESSOR
Class D
MODE
WOOFER
DRIVER
BALANCED
INPUTS
LINK
L
N
MAINS
FUSE
POWER
SWITCH
TRANSFORMER
INPUT
SENS
L
N
MAINS
FUSE
POWER
SWITCH
READYLIMITER
SIGNAL
SENSITIVITY
Class D
®
DIGIPRO
DSP
Digital Signal Processing
MICROPROCESSOR
Class D
MODE
WOOFER
DRIVER
BALANCED
INPUTS
LINK
INPUT
SENS
INTERNAL
POWER
SUPPLY
200W
400W
600W
FLEXSYS F8
FLEXSYS F10
FLEXSYS F12
FLEXSYS F15
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29

dB Technologies FLEXSYS F10 User manual

Category
Car audio amplifiers
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI