Hikoki CH 105EC (C) Owner's manual

Category
Power hedge trimmers
Type
Owner's manual
5
English
MEANINGS OF SYMBOLS
NOTE: Some units do not carry them.
Symbols
WARNING
The following show symbols used for the machine. Be sure that you understand their meaning before use.
It is important that you read, fully understand and observe the following safety precautions and warnings.
Careless or improper use of the unit may cause serious or fatal injury.
Read, understand and follow all warnings and instructions in this manual and on the unit.
Always wear eye, head and ear protectors when using this unit.
Before using your machine
• Read the manual carefully.
• Check that the cutting equipment is correctly assembled and adjusted.
• Start the unit and check the carburetor adjustment. See “MAINTENANCE”.
Contents
WHAT IS WHAT? ...............................................................................6
WARNINGS AND SAFETY INSTRUCTIONS ...................................7
SPECIFICATIONS .............................................................................8
ASSEMBLY PROCEDURES ............................................................10
OPERATING PROCEDURES ..........................................................10
MAI NT ENA NCE ............................................................................... 10
6
English
19
20
1
2
8
5
9
12
13
18
7
11
3
6
4
14
15
10
CH78EB (C), CH78EC (SC)
CH78EC (C), CH105EC (C)
CH78ED (CP)
6
3
11
10
13
18
14
5
7
8
9
12
1
17
2
4
CH66EB (ST)
CH55EB (ST), CH50EA (ST), CH62EA (ST)
CH78EC (ST)
CH66ED (TP), CH78ED (TP)
16
12
9
10
13
15
4
6
3
11
2
1
14
5
7
8
16
CH50EB
18
WHAT IS WHAT?
Since this manual covers several models, there may be some
di erence between these illustrations and your unit. Use the
instructions that apply to your unit.
1. Recoil starter
2. Fuel tank
3. Throttle trigger lookout
4. Throttle trigger
5. Front handle
6. Rear handle
7. Spark pl ug
8. Hand guard
9. Cutting blade
10. Air cleaner
11. Ignition switch
12. Blunt guard
13. Gear case
14. Choke lever
15. Lock button (optional)
16. Blade cover
17. Lock button
18. Priming pump
19. Combi box spanner
20. Handling instructions
7
English
WARNINGS AND SAFETY INSTRUCTIONS
Operator safety
Always wear a safety face shield or goggles.
Always wear heavy, long pants, boots and gloves. Do not wear
loose clothing, jewelry, short pants, sandals or go barefoot.
Secure hair so it is above shoulder length.
Do not operate this tool when you are tired, ill or under the
in uence of alcohol, drugs or medication.
Never let a child or inexperienced person operate the machine.
Wear hearing protection.
Never start or run the engine inside a closed room or building.
Breathing exhaust fumes can kill.
Keep handles free of oil and fuel.
Keep hands away from cutting equipment.
Do not grab or hold the unit by the cutting equipment.
When the unit is turned o , make sure the cutting attachment
has stopped before the unit is set down.
When operation is prolonged, take a break from time to time
so that you may avoid possible Hand-Arm Vibration Syndrome
(HAVS) which is caused by vibration.
WARNING
Antivibration systems do not guarantee that you will not sustain
Hand-Arm Vibration Syndrome or carpal tunnel syndrome.
Therefore, continual and regular users should monitor closely
the condition of their hands and ngers. If any symptoms of the
above appear, seek medical advice immediately.
If you are using any medical electric/electronic devices such
as a pacemaker, consult your physician as well as the device
manufacturer prior to operating any power equipment.
Unit/machine safety
Inspect the entire unit/machine before each use. Replace
damaged parts. Check for fuel leaks and make sure all
fasteners are in place and securely tightened.
Replace parts that are cracked, chipped or damaged in any way
before using the unit/machine.
Make sure the safety guard is properly attached.
Keep others away when making carburetor adjustments.
Use only accessories as recommended for this unit/machine by
the manufacturer.
WARNING
Never modify the unit/machine in any way. Do not use your unit/
machine for any job except that for which it is intended.
Fuel safety
Mix and pour fuel outdoors and where there are no sparks or
ames.
Use a container approved for fuel.
Do not smoke or allow smoking near fuel or the unit/machine or
while using the unit/machine.
Wipe up all fuel spills before starting engine.
Move at least 3 m away from fueling site before starting engine.
Stop engine before removing fuel cap.
Empty the fuel tank before storing the unit/machine. It is
recommended that the fuel be emptied after each use. If fuel is
left in the tank, store so fuel will not leak.
Store unit/machine and fuel in area where fuel vapors cannot
reach sparks or open ames from water heaters, electric motors
or switches, furnaces, etc.
WARNING
Fuel is easy to ignite or get explosion or inhale fumes, so that
pay special attention when handling or lling fuel.
Cutting safety
Do not cut any material other than plant hedge.
Inspect the area to be cut before each use. Remove objects
which can be thrown or become entangled.
For respiratory protection, wear an aerosol protection mask
when cutting the grass after insecticide is scattered.
Keep others including children, animals, bystanders and
helpers outside the 15 m hazard zone. Stop the engine
immediately if you are approached.
Hold the unit/machine rmly with both hands.
Keep rm footing and balance. Do not over-reach.
Keep all parts of your body away from the mu er and cutting
attachment when the engine is running.
Keep cutting tool below shoulder level. NEVER operate unit
from a ladder, while in a tree or from any unstable support.
When relocating to a new work area, be sure to shut o the
machine and ensure that all cutting attachments are stopped.
Never place the machine on the ground when running.
Always carry a rst-aid kit when operating any power
equipment.
Never start or run the engine inside a closed room or building
and/or near the in ammable liquid. Breathing exhaust fumes
can kill.
Maintenance safety
Maintain the unit/machine according to recommended
procedures.
Disconnect the spark plug before performing maintenance
except for carburetor adjustments.
Keep others away when making carburetor adjustments.
Use only genuine Hitachi replacement parts as recommended
by the manufacturer.
Transpor t and storage
Carry the unit/machine by hand with the engine stopped and
the mu er away from your body.
Allow the engine to cool, empty the fuel tank, and secure the
unit/machine before storing or transporting in a vehicle.
Empty the fuel tank before storing the unit/machine. It is
recommended that the fuel be emptied after each use. If fuel is
left in the tank, store so fuel will not leak.
Store unit/machine out of the reach of children.
Clean and maintenance the unit carefully and store it in a dry
place.
Make sure engine switch is o when transporting or storing.
When transporting in a vehicle or storage, cover blade with
blade cover.
If situations occur which are not covered in this manual, take care
and use common sense. Contact your Hitachi dealer if you need
assistance. Pay special attention to statements preceded by the
following words:
WARNING
Indicates a strong possibility of severe personal injury or loss of
life, if instructions are not followed.
CAUTION
Indicates a possibility of personal injury or equipment damage,
if instructions are not followed.
NOTE
Helpful information for correct function and use.
CAUTION
Do not disassemble the recoil starter. You may get a possibility
of personal injury with recoil spring.
8
English
SPECIFICATIONS
MODEL
CH50EB/CH66EB (ST)
CH55EB (ST)/CH50EA (ST)
CH62EA (ST)
CH78EC (ST) CH78EB (C)
Engine Size (ml) 22 24 22
Spark Plug
NGK BPM-6A or BPMR-6A
Champion CJ-8Y or RCJ-8Y
NGK BPM-6A or BPMR-6A
Champion CJ-8Y or RCJ-8Y
NGK BPM-6A or BPMR-6A
Champion CJ-8Y or RCJ-8Y
Fuel Tank Capacity (l) 0.35 0.35 0.35
Dry Weight (kg)
CH50EB .......................... 4.1
CH55EB (ST) .................. 4.5
CH66EB (ST) .................. 5.0
CH50EA (ST) .................. 4.3
CH62EA (ST) .................. 4.6
5.3 5.2
Overall cutter length
(mm)
CH50EA (ST)/CH50EB
...... 500
CH66EB (ST) .................. 650
CH55EB (ST) .................. 550
CH62EA (ST) .................. 620
770 770
:
Blade type
:
△△
Sound pressure level
LpA (dB(A))
(EN 27917)
CH50EB ....................... 100.0
CH66EB (ST) .................. 92.1
CH55EB (ST) .................. 93.6
CH50EA (ST)/CH62EA (ST)
..... 97.0
91.1 91.4
Sound power level
LwA (dB(A))
(2000/14/EC)
104 104 104
Vibration level (m/s
2
) (ISO 7916)
Front handle
Rear handle
CH66EB (ST) ..................
4.5
CH50EB ..........................
5.3
CH55EB (ST) ..................
4.2
CH50EA (ST)/CH62EA (ST)
.......
5.1/6.5
CH66EB (ST) ..................
5.2
CH50EB ..........................
11. 5
CH55EB (ST) ..................
12.3
CH50EA (ST)/CH62EA (ST)
.......
11. 3/9.2
7.6
6.2
3.5
5.3
NOTE
Equivalent noise level/vibration level are calculated as the time-weighted energy total for noise/vibration levels under various working
conditions with the following time distribution : 1/2 idle, 1/2 racing.
* All data is subject to change without notice.
9
English
MODEL
CH78EC (SC)
CH78EC (C)
CH105EC (C)
CH66ED (TP)
CH78ED (TP)
CH78ED (CP)
Engine Size (ml) 24 24 24
Spark Plug
NGK BPM-6A or BPMR-6A
Champion CJ-8Y or RCJ-8Y
NGK BPM-6A or BPMR-6A
Champion CJ-8Y or RCJ-8Y
NGK BPM-6A or BPMR-6A
Champion CJ-8Y or RCJ-8Y
Fuel Tank Capacity (l)
0.35
0.33 0.33
Dry Weight (kg)
CH78EC (SC) ........ 5.2
CH78EC (C) ..........5.2
CH105EC (C) ........5.6
CH66ED (TP) ...........5.3
CH78ED (TP) ...........5.6
5.6
Overall cutter length
(mm)
CH78EC (SC) ........ 770
CH78EC (C) ..........770
CH105EC (C) ........1000
CH66ED (TP) .......... 650
CH78ED (TP) .......... 770
770
:
Blade type
:
Sound pressure level
LpA (dB(A))
(EN 27917)
CH78EC (SC) ........ 93.9
CH78EC (C)
CH105EC (C) ........96.7/96.7
98.3 98.3
Sound power level
LwA (dB(A))
(2000/14/EC)
104 104 104
Vibration level (m/s
2
) (ISO 7916)
Front handle
Rear handle
CH78EC (SC) ........ 4.7
CH78EC (C)
CH105EC (C) ........6.8
CH78EC (SC) ........ 6.4
CH78EC (C)
CH105EC (C) ........5.6
CH66ED (TP) ...........8.9
CH78ED (TP) ...........7.8
CH66ED (TP) ...........6.3
CH78ED (TP) ...........5.3
6.1
11.1
NOTE
Equivalent noise level/vibration level are calculated as the time-weighted energy total for noise/vibration levels under various working
conditions with the following time distribution : 1/2 idle, 1/2 racing.
* All data is subject to change without notice.
10
English
ASSEMBLY PROCEDURES
Handle B (3) and Gathering plate (4) (Fig. 1)
1. Remove the four washers and nuts (1) from cutting blade end.
NOTE
In case of Handle B installation only, remove only the nut on the
longest bolt.
2. Set the gathering plate on the cutter guide, then nger tighten
the three washers and nuts.
* Use one each (5) of the two washers, which have been
provided, under the gathering plate or on the two blade- xing
bolts from the cutting-blade end to install the gathering plate
on CH105EC (C). (If so equipped)
3. Set the handle B on the longest bolt and nger tighten with the
washer and nut.
4. Before securing the nger-tightened nuts, screw the blade xing
bolts (2) to be seated, then loosen the bolts approx. 1/2 turn.
5. With the bolts set at that position tighten the blade xing nuts.
OPERATING PROCEDURES
Fuel (Fig. 2)
WARNING
The hedge trimmer is equipped with a two- stroke engine.
Always run the engine on fuel, mixed with oil.
Provide good ventilation, when fueling or handling fuel.
Fuel
Always use branded 89 octane unleaded gasoline.
Use genuine two-cycle oil or use a mix between 25:1 to 50:1,
please consult the oil bottle for the ratio or Hitachi dealer.
If genuine oil is not available, use an anti-oxidant added quality
oil expressly labeled for air-cooled 2-cycle engine use (JASO
FC GRADE OIL or ISO EGC GRADE). Do not use BIA or TCW
(2-stroke water-cooling type) mixed oil.
Never use multi-grade oil (10W/30) or waste oil.
Always mix fuel and oil in a separate clean container.
Always start by lling half the amount of fuel, which is to be used.
Then add the whole amount of oil. Mix (shake) the fuel mixture. Add
the remaining amount of fuel.
Mix (shake) the fuel-mix thoroughly before lling the fuel tank.
Fueling
WARNING (Fig. 3)
Always shut o the engine before refueling.
Slowly open the fuel tank (6), when lling up with fuel, so that
possible over-pressure disappears.
Tighten the fuel cap carefully, after fueling.
Always move the unit at least 3 m from the fueling area before
starting.
Before fueling, clean the tank cap area carefully, to ensure that
no dirt falls into the tank. Make sure that the fuel is well mixed by
shaking the container, before fueling.
Starting
CAUTION
Before starting, make sure the cutting attachment does not
touch anything.
1. Set ignition switch (7) to ON position (A). (Fig. 4, 5)
* Push priming bulb (10) several times so that fuel ows through
the bulb or return pipe. (If so equipped) (Fig. 6)
2. With the safety lever (8) pressed, pull throttle trigger and push
lock button (9) (If so equipped), then slowly release throttle the
trigger rst, then the safety lever. This will lock the throttle in
starting position. (Fig. 4, 5)
3. Set choke lever (11) to CLOSED position (B). (Fig. 7)
4. Pull recoil starter briskly, taking care to keep the handle in your
grasp and not allowing it to snap back. (Fig. 8, 9)
5. When you hear the engine attempts to start, return choke lever
to RUN position (open) (C). Then pull recoil starter briskly
again.
NOTE
If engine does not start, repeat procedures from 2 to 4.
6. After starting engine, allow the engine about 2-3 minutes to
warm up before subjecting it to any load.
Cutting
When cutting, operate engine at full throttle as this maintains proper
cutter speed. When trimming top of hedge, hold trimmer so blades
are between 15 and 30 degrees from a horizontal position and
swing trimmer in an arc toward edge of hedge to sweep cuttings o .
When trimming sides of hedge, hold blade vertically and swing unit
in an arc.
NOTE
Multi-position twist handle (Fig. 10)
In case your trimmer is twist handle type (12), please note that
the cutting angle can be adjusted by loosening handle locking
nut (13). After adjustment has been made, be sure to retighten
the nut.
Five positioning twist handle (Fig. 11)
The rear handle can be set in ve di erent positions by pushing
the lock button (14) and turning the rear handle (15).
It is extremely important that the handle is locked in the selected
position.
The lock button can not work while the throttle trigger is being
pulled.
The throttle trigger will not work if the rear handle is unlocked.
Stopping (Fig. 12, 13)
Decrease engine speed, and push ignition switch to stop position
(F).
MAINTENANCE
MAINTENANCE, REPLACEMENT OR REPAIR OF THE EMISSION
CONTROL DEVICES AND SYSTEM MAY BE PERFORMED
BY ANY NONROAD ENGINE REPAIR ESTABLISHMENT OR
INDIVIDUAL.
Carburetor adjustment (Fig. 14)
WARNING
The cutting attachment may be spinning during carburetor
adjustments.
Never start the engine without the complete clutch cover.
Otherwise the clutch can come loose and cause personal
injuries.
In the carburetor, fuel is mixed with air. When the engine is test run
at the factory, the carburetor is adjusted. A further adjustment may
be required, according to climate and altitude. The carburetor has
one adjustment possibility:
T = Idle speed adjustment screw.
Idle speed adjustment (T)
Check that the air lter is clean. When the idle speed is correct, the
cutting attachment will not rotate. If adjustment is required, close
(clockwise) the T-screw, with the engine running, until the cutting
attachment starts to rotate. Open (counter-clockwise) the screw
until the cutting attachment stops. You have reached the correct idle
speed when the engine runs smoothly in all positions well below the
rpm when the cutting attachment starts to rotate.
If the cutting attachment still rotates after idle speed adjustment,
contact Hitachi dealer.
11
English
Air lter (Fig. 15)
The air lter must be cleaned from dust and dirt in order to avoid:
Carburetor malfunctions.
Starting problems.
Engine power reduction.
Unnecessary wear on the engine parts.
Abnormal fuel consumption.
Clean the air lter daily or more often if working in exceptionally
dusty areas.
Cleaning the air lter
Remove the air lter cover and the lter. Rinse it in warm soap suds.
Check that the lter is dry before reassembly. An air lter that has
been used for some time cannot be cleaned completely. Therefore,
it must regularly be replaced by a new one. A damaged lter must
always be replaced.
NOTE
Saturate the element in 2-cycle oil or the equivalent. Squeeze
the element to distribute the oil completely and to remove any
excess oil.
Spark plug (Fig. 16)
The spark plug condition is in uenced by:
An incorrect carburetor setting.
Wrong fuel mixture (too much oil in the gasoline).
A dirty air lter.
Hard running conditions (such as cold weather).
These factors cause deposits on the spark plug electrodes, which
may result in malfunction and starting di culties. If the engine
is low on power, di cult to start or runs poorly at idling speed,
always check the spark plug rst. If the spark plug is dirty, clean it
and check the electrode gap. Readjust if necessary. The correct
gap is 0.6 mm. The spark plug should be replaced after about 100
operation hours or earlier if the electrodes are badly eroded.
NOTE
In some areas, local law requires using a resistor spark plug
to suppress ignition signals. If this machine was originally
equipped with resistor spark plug, use the same type of spark
plug for replacement.
Cutter blade (Fig. 17, 18)
The blades are installed to the cutter guide with the four or ve
bolts. Those bolts are tightened with a clearance so that the cutters
can move smoothly.
When
clearance is too small
The cutters do not move properly and the sliding surfaces may
seize.
When clearance is too large
The cutters are poor in sharpness.
To adjust the cutter clearance
1. Loosen the cutter xing nuts.
2. Fully tighten the cutter xing bolts and then loosen them approx.
1/2 turn.
3. With the bolts set at that position, tighten the cutter xing nuts.
Be sure to replace cutter guide xing bolts when they are loosened,
worn or damaged. Also be sure to replace damaged cutter blade.
NOTE
Properly lubricate the cutter sliding surfaces with machine oil.
Gear case (Fig. 19)
Apply a good quality lithium based grease through the grease tting
until a small amount comes out between the cutter blades and the
gear case.
NOTE
Lubrication should be applied at 50 hour intervals and more
frequently with heavy use.
Fuel lter (Fig. 20)
Remove the fuel lter from the fuel tank and thoroughly wash it in
solvent. After that, push the lter into the tank completely.
NOTE
If the lter is hard due to dust and dirt, replace it.
Cleaning the cylinder ns (Fig. 21)
When leaves get caught between cylinder ns (16), the engine
may overheat, resulting in lower output. To avoid this, always keep
cylinder ns and fan case clean.
Every 100 operating hours, or once a year (more often if conditions
require), clean ns and external surfaces of engine of dust, dirt and
oil deposits which can contribute to improper cooling.
Cleaning
the mu er (Fig. 22)
Remove the mu er and spark arrestor (if so equipped), and clean
out any excess carbon from the exhaust port or mu er inlet every
100 hours of operation.
For long-term storage
Drain all fuel from the fuel tank. Start and let engine run until it stops.
Repair any damage which has resulted from use. Clean the unit with
a clean rag, or high pressure air hose. Put a few drops of two-cycle
engine oil into the cylinder through the spark plug hole, and spin the
engine over several times to distribute oil. Cover the unit and store
it in a dry area.
Maintenance schedule
Below you will nd some general maintenance instructions. For
further information please contact your Hitachi dealer.
Daily maintenance
Clean the exterior of the hedge trimmer.
Check the blade guard for damage or cracks. Change the guard
in case of impacts or cracks.
Check that the blade is sharp, and without cracks.
Check that the blade nut is su ciently tightened.
Make sure that the blade transport guard is undamaged and
that it can be securely tted.
Check that nuts and screws are su ciently tightened.
Weekly maintenance
Check the starter, especially cord and return spring.
Clean the exterior of the spark plug.
Remove it and check the electrode gap. Adjust it to 0.6 mm, or
change the spark plug.
Clean the cooling ns on the cylinder and check that the air
intake at the starter is not clogged.
Check gear case is lled with grease.
Clean the air lter.
Monthly maintenance
Rinse the fuel tank with gasoline.
Clean the exterior of the carburetor and the space around it.
Clean the fan and the space around it.
16
Deutsch
MODELL
CH50EB/CH66EB (ST)
CH55EB (ST)/CH50EA (ST)
CH62EA (ST)
CH78EC (ST) CH78EB (C)
Motorgröße (ml) 22 24 22
Zündkerze
NGK BPM-6A oder BPMR-6A
Champion CJ-8Y oder RCJ-8Y
NGK BPM-6A oder BPMR-6A
Champion CJ-8Y oder RCJ-8Y
NGK BPM-6A oder BPMR-6A
Champion CJ-8Y oder RCJ-8Y
Kapazität des
Kraftsto tanks (l)
0,35 0,35 0,35
Leergewicht (kg)
CH50EB .......................... 4,1
CH55EB (ST) .................. 4,5
CH66EB (ST) .................. 5,0
CH50EA (ST) .................. 4,3
CH62EA (ST) .................. 4,6
5,3 5,2
Gesamtlänge
Schneideblatt (mm)
CH50EA (ST)/CH50EB
...... 500
CH66EB (ST) .................. 650
CH55EB (ST) .................. 550
CH62EA (ST) .................. 620
770 770
:
Art der Klinge
:
△△
Schalldruckpegel
LpA (dB(A))
(EN 27917)
CH50EB ....................... 100,0
CH66EB (ST) .................. 92,1
CH55EB (ST) .................. 93,6
CH50EA (ST)/CH62EA (ST)
..... 97,0
91,1 91,4
Geräuschpegel
LwA (dB(A))
(2000/14/EC)
104 104 104
Vibrationspegel (m/s
2
) (ISO 7916)
Vorderer Gri
Hinterer Gri
CH66EB (ST) ..................
4,5
CH50EB ..........................
5,3
CH55EB (ST) ..................
4,2
CH50EA (ST)/CH62EA (ST)
.......
5,1/6,5
CH66EB (ST) ..................
5,2
CH50EB ..........................
11, 5
CH55EB (ST) ..................
12,3
CH50EA (ST)/CH62EA (ST)
.......
11, 3/9,2
7,6
6,2
3,5
5,3
HINWEIS
Die entsprechenden Geräusch-/Vibrationspegel werden aus der gesamten Geräusch-/Vibrationsenergie zeitgewichtet unter
verschiedenen Arbeitsbedingungen mit folgender Zeitverteilung berechnet: 1/2 Leerlauf, 1/2 schnell.
* Änderungen der technischen Daten jederzeit vorbehalten.
TECHNISCHE DATEN
17
Deutsch
MODELL
CH78EC (SC)
CH78EC (C)
CH105EC (C)
CH66ED (TP)
CH78ED (TP)
CH78ED (CP)
Motorgröße (ml) 24 24 24
Zündkerze
NGK BPM-6A oder BPMR-6A
Champion CJ-8Y oder RCJ-8Y
NGK BPM-6A oder BPMR-6A
Champion CJ-8Y oder RCJ-8Y
NGK BPM-6A oder BPMR-6A
Champion CJ-8Y oder RCJ-8Y
Kapazität des
Kraftsto tanks (l)
0,35
0,33 0,33
Leergewicht (kg)
CH78EC (SC) ........ 5,2
CH78EC (C) ..........5,2
CH105EC (C) ........5,6
CH66ED (TP) ...........5,3
CH78ED (TP) ...........5,6
5,6
Gesamtlänge
Schneideblatt (mm)
CH78EC (SC) ........ 770
CH78EC (C) ..........770
CH105EC (C) ........1000
CH66ED (TP) .......... 650
CH78ED (TP) .......... 770
770
:
Art der Klinge
:
Schalldruckpegel
LpA (dB(A))
(EN 27917)
CH78EC (SC) ........ 93,9
CH78EC (C)
CH105EC (C) ........96,7/96,7
98,3 98,3
Geräuschpegel
LwA (dB(A))
(2000/14/EC)
104 104 104
Vibrationspegel (m/s
2
) (ISO 7916)
Vorderer Gri
Hinterer Gri
CH78EC (SC) ........ 4,7
CH78EC (C)
CH105EC (C) ........6,8
CH78EC (SC) ........ 6,4
CH78EC (C)
CH105EC (C) ........5,6
CH66ED (TP) ...........8,9
CH78ED (TP) ...........7,8
CH66ED (TP) ...........6,3
CH78ED (TP) ...........5,3
6,1
11,1
HINWEIS
Die entsprechenden Geräusch-/Vibrationspegel werden aus der gesamten Geräusch-/Vibrationsenergie zeitgewichtet unter
verschiedenen Arbeitsbedingungen mit folgender Zeitverteilung berechnet: 1/2 Leerlauf, 1/2 schnell.
* Änderungen der technischen Daten jederzeit vorbehalten.
25
Français
MODÈLE
CH50EB/CH66EB (ST)
CH55EB (ST)/CH50EA (ST)
CH62EA (ST)
CH78EC (ST) CH78EB (C)
Taille du moteur (ml) 22 24 22
Bougie d’allumage
NGK BPM-6A ou BPMR-6A
Champion CJ-8Y ou RCJ-8Y
NGK BPM-6A ou BPMR-6A
Champion CJ-8Y ou RCJ-8Y
NGK BPM-6A ou BPMR-6A
Champion CJ-8Y ou RCJ-8Y
Contenance
du réservoir de
carburant (l)
0,35 0,35 0,35
Poids à sec (kg)
CH50EB .......................... 4,1
CH55EB (ST) .................. 4,5
CH66EB (ST) .................. 5,0
CH50EA (ST) .................. 4,3
CH62EA (ST) .................. 4,6
5,3 5,2
Longueur hors tout
du couteau (mm)
CH50EA (ST)/CH50EB
...... 500
CH66EB (ST) .................. 650
CH55EB (ST) .................. 550
CH62EA (ST) .................. 620
770 770
:
Type de lame
:
△△
Niveau de pression
sonore
LpA (dB(A))
(EN 27917)
CH50EB ....................... 100,0
CH66EB (ST) .................. 92,1
CH55EB (ST) .................. 93,6
CH50EA (ST)/CH62EA (ST)
..... 97,0
91,1 91,4
Niveau de puissance
sonore
LwA (dB(A))
(2000/14/EC)
104 104 104
Niveau de vibrations (m/s
2
) (ISO 7916)
Poignée avant
Poignée arrre
CH66EB (ST) ..................
4,5
CH50EB ..........................
5,3
CH55EB (ST) ..................
4,2
CH50EA (ST)/CH62EA (ST)
.......
5,1/6,5
CH66EB (ST) ..................
5,2
CH50EB ..........................
11, 5
CH55EB (ST) ..................
12,3
CH50EA (ST)/CH62EA (ST)
.......
11, 3/9,2
7,6
6,2
3,5
5,3
REMARQUE
Les niveaux de bruit/vibrations équivalents sont calcus comme total d’énergie pone en fonction du temps pour les niveaux de
bruit/vibrations dans diverses conditions de travail avec la répartition temporelle suivante : 1/2 ralenti, 1/2 vitesse de course.
* Toutes les dones sont susceptibles d’être modi ées sans préavis.
CARACRISTIQUES
26
Français
MODÈLE
CH78EC (SC)
CH78EC (C)
CH105EC (C)
CH66ED (TP)
CH78ED (TP)
CH78ED (CP)
Taille du moteur (ml) 24 24 24
Bougie d’allumage
NGK BPM-6A ou BPMR-6A
Champion CJ-8Y ou RCJ-8Y
NGK BPM-6A ou BPMR-6A
Champion CJ-8Y ou RCJ-8Y
NGK BPM-6A ou BPMR-6A
Champion CJ-8Y ou RCJ-8Y
Contenance
du réservoir de
carburant (l)
0,35
0,33 0,33
Poids à sec (kg)
CH78EC (SC) ........ 5,2
CH78EC (C) ..........5,2
CH105EC (C) ........5,6
CH66ED (TP) ...........5,3
CH78ED (TP) ...........5,6
5,6
Longueur hors tout
du couteau (mm)
CH78EC (SC) ........ 770
CH78EC (C) ..........770
CH105EC (C) ........1000
CH66ED (TP) .......... 650
CH78ED (TP) .......... 770
770
:
Type de lame
:
Niveau de pression
sonore
LpA (dB(A))
(EN 27917)
CH78EC (SC) ........ 93,9
CH78EC (C)
CH105EC (C) ........96,7/96,7
98,3 98,3
Niveau de puissance
sonore
LwA (dB(A))
(2000/14/EC)
104 104 104
Niveau de vibrations (m/s
2
) (ISO 7916)
Poignée avant
Poignée arrre
CH78EC (SC) ........ 4,7
CH78EC (C)
CH105EC (C) ........6,8
CH78EC (SC) ........ 6,4
CH78EC (C)
CH105EC (C) ........5,6
CH66ED (TP) ...........8,9
CH78ED (TP) ...........7,8
CH66ED (TP) ...........6,3
CH78ED (TP) ...........5,3
6,1
11,1
REMARQUE
Les niveaux de bruit/vibrations équivalents sont calcus comme total d’énergie pone en fonction du temps pour les niveaux de
bruit/vibrations dans diverses conditions de travail avec la répartition temporelle suivante : 1/2 ralenti, 1/2 vitesse de course.
* Toutes les données sont susceptibles d’être modi ées sans préavis.
33
Italiano
SPECIFICHE
MODELLO
CH50EB/CH66EB (ST)
CH55EB (ST)/CH50EA (ST)
CH62EA (ST)
CH78EC (ST) CH78EB (C)
Cilindrata del motore
(ml)
22 24 22
Candela di
accensione
NGK BPM-6A o BPMR-6A
Champion CJ-8Y o RCJ-8Y
NGK BPM-6A o BPMR-6A
Champion CJ-8Y o RCJ-8Y
NGK BPM-6A o BPMR-6A
Champion CJ-8Y o RCJ-8Y
Capacità del
serbatoio carburante
(l)
0,35 0,35 0,35
Peso a secco (kg)
CH50EB .......................... 4,1
CH55EB (ST) .................. 4,5
CH66EB (ST) .................. 5,0
CH50EA (ST) .................. 4,3
CH62EA (ST) .................. 4,6
5,3 5,2
Lunghezza totale del
dispositivo di taglio
(mm)
CH50EA (ST)/CH50EB
...... 500
CH66EB (ST) .................. 650
CH55EB (ST) .................. 550
CH62EA (ST) .................. 620
770 770
:
Tipo di lama
:
△△
Livello di pressione
acustica
LpA (dB(A))
(EN 27917)
CH50EB ....................... 100,0
CH66EB (ST) .................. 92,1
CH55EB (ST) .................. 93,6
CH50EA (ST)/CH62EA (ST)
..... 97,0
91,1 91,4
Livello di potenza
acustica
LwA (dB(A))
(2000/14/EC)
104 104 104
Livello di vibrazione (m/s
2
) (ISO 7916)
Impugnatura anteriore
Impugnatura posteriore
CH66EB (ST) ..................
4,5
CH50EB ..........................
5,3
CH55EB (ST) ..................
4,2
CH50EA (ST)/CH62EA (ST)
.......
5,1/6,5
CH66EB (ST) ..................
5,2
CH50EB ..........................
11, 5
CH55EB (ST) ..................
12,3
CH50EA (ST)/CH62EA (ST)
.......
11, 3/9,2
7,6
6,2
3,5
5,3
NOTA
II livello di rumore/livello di vibrazioni equivalenti sono calcolati come la media ponderata sull’arco di tempo, per varie condizioni di
funzionamento con la seguente distribuzione dei tempi: 1/2 minimo, 1/2 velocità di lavoro.
* Tutti i dati sono soggetti a modi che senza preavviso.
34
Italiano
MODELLO
CH78EC (SC)
CH78EC (C)
CH105EC (C)
CH66ED (TP)
CH78ED (TP)
CH78ED (CP)
Cilindrata del motore
(ml)
24 24 24
Candela di
accensione
NGK BPM-6A o BPMR-6A
Champion CJ-8Y o RCJ-8Y
NGK BPM-6A o BPMR-6A
Champion CJ-8Y o RCJ-8Y
NGK BPM-6A o BPMR-6A
Champion CJ-8Y o RCJ-8Y
Capacità del
serbatoio carburante
(l)
0,35
0,33 0,33
Peso a secco (kg)
CH78EC (SC) ........ 5,2
CH78EC (C) ..........5,2
CH105EC (C) ........5,6
CH66ED (TP) ...........5,3
CH78ED (TP) ...........5,6
5,6
Lunghezza totale del
dispositivo di taglio
(mm)
CH78EC (SC) ........ 770
CH78EC (C) ..........770
CH105EC (C) ........1000
CH66ED (TP) .......... 650
CH78ED (TP) .......... 770
770
:
Tipo di lama
:
Livello di pressione
acustica
LpA (dB(A))
(EN 27917)
CH78EC (SC) ........ 93,9
CH78EC (C)
CH105EC (C) ........96,7/96,7
98,3 98,3
Livello di potenza
acustica
LwA (dB(A))
(2000/14/EC)
104 104 104
Livello di vibrazione (m/s
2
) (ISO 7916)
Impugnatura anteriore
Impugnatura posteriore
CH78EC (SC) ........ 4,7
CH78EC (C)
CH105EC (C) ........6,8
CH78EC (SC) ........ 6,4
CH78EC (C)
CH105EC (C) ........5,6
CH66ED (TP) ...........8,9
CH78ED (TP) ...........7,8
CH66ED (TP) ...........6,3
CH78ED (TP) ...........5,3
6,1
11,1
NOTA
II livello di rumore/livello di vibrazioni equivalenti sono calcolati come la media ponderata sull’arco di tempo, per varie condizioni di
funzionamento con la seguente distribuzione dei tempi: 1/2 minimo, 1/2 velocità di lavoro.
* Tutti i dati sono soggetti a modi che senza preavviso.
40
Nederlands
SPECIFICATIES
MODEL
CH50EB/CH66EB (ST)
CH55EB (ST)/CH50EA (ST)
CH62EA (ST)
CH78EC (ST) CH78EB (C)
Motorinhoud (ml) 22 24 22
Bougie
NGK BPM-6A of BPMR-6A
Champion CJ-8Y of RCJ-8Y
NGK BPM-6A of BPMR-6A
Champion CJ-8Y of RCJ-8Y
NGK BPM-6A of BPMR-6A
Champion CJ-8Y of RCJ-8Y
Capaciteit
brandstoftank (l)
0,35 0,35 0,35
Droog gewicht (kg)
CH50EB .......................... 4,1
CH55EB (ST) .................. 4,5
CH66EB (ST) .................. 5,0
CH50EA (ST) .................. 4,3
CH62EA (ST) .................. 4,6
5,3 5,2
Totale meslengte
(mm)
CH50EA (ST)/CH50EB
...... 500
CH66EB (ST) .................. 650
CH55EB (ST) .................. 550
CH62EA (ST) .................. 620
770 770
:
Mesbladtype
:
△△
Geluidsdrukniveau
LpA (dB(A))
(EN 27917)
CH50EB ....................... 100,0
CH66EB (ST) .................. 92,1
CH55EB (ST) .................. 93,6
CH50EA (ST)/CH62EA (ST)
..... 97,0
91,1 91,4
Geluidsvermogenniveau
LwA (dB(A))
(2000/14/EC)
104 104 104
Vibratieniveau (m/s
2
) (ISO 7916)
Voorste handgreep
Achterste handgreep
CH66EB (ST) ..................
4,5
CH50EB ..........................
5,3
CH55EB (ST) ..................
4,2
CH50EA (ST)/CH62EA (ST)
.......
5,1/6,5
CH66EB (ST) ..................
5,2
CH50EB ..........................
11, 5
CH55EB (ST) ..................
12,3
CH50EA (ST)/CH62EA (ST)
.......
11, 3/9,2
7,6
6,2
3,5
5,3
OPMERKING
Equivalent geluidsniveau/vibratieniveau werd berekend zoals de tijdgewogen totale energie voor geluids-/vibratieniveaus, onder
verschillende werkomstandigheden met de volgende tijdsverdeling: 1/2 onbelaste loop, 1/2 belaste loop.
* Wijzigingen in de gegevens voorbehouden, zonder voorafgaande kennisgeving.
41
Nederlands
MODEL
CH78EC (SC)
CH78EC (C)
CH105EC (C)
CH66ED (TP)
CH78ED (TP)
CH78ED (CP)
Motorinhoud (ml) 24 24 24
Bougie
NGK BPM-6A of BPMR-6A
Champion CJ-8Y of RCJ-8Y
NGK BPM-6A of BPMR-6A
Champion CJ-8Y of RCJ-8Y
NGK BPM-6A of BPMR-6A
Champion CJ-8Y of RCJ-8Y
Capaciteit
brandstoftank (l)
0,35
0,33 0,33
Droog gewicht (kg)
CH78EC (SC) ........ 5,2
CH78EC (C) ..........5,2
CH105EC (C) ........5,6
CH66ED (TP) ...........5,3
CH78ED (TP) ...........5,6
5,6
Totale meslengte
(mm)
CH78EC (SC) ........ 770
CH78EC (C) ..........770
CH105EC (C) ........1000
CH66ED (TP) .......... 650
CH78ED (TP) .......... 770
770
:
Mesbladtype
:
Geluidsdrukniveau
LpA (dB(A))
(EN 27917)
CH78EC (SC) ........ 93,9
CH78EC (C)
CH105EC (C) ........96,7/96,7
98,3 98,3
Geluidsvermogenniveau
LwA (dB(A))
(2000/14/EC)
104 104 104
Vibratieniveau (m/s
2
) (ISO 7916)
Voorste handgreep
Achterste handgreep
CH78EC (SC) ........ 4,7
CH78EC (C)
CH105EC (C) ........6,8
CH78EC (SC) ........ 6,4
CH78EC (C)
CH105EC (C) ........5,6
CH66ED (TP) ...........8,9
CH78ED (TP) ...........7,8
CH66ED (TP) ...........6,3
CH78ED (TP) ...........5,3
6,1
11,1
OPMERKING
Equivalent geluidsniveau/vibratieniveau werd berekend zoals de tijdgewogen totale energie voor geluids-/vibratieniveaus, onder
verschillende werkomstandigheden met de volgende tijdsverdeling: 1/2 onbelaste loop, 1/2 belaste loop.
* Wijzigingen in de gegevens voorbehouden, zonder voorafgaande kennisgeving.
48
Español
ESPECIFICACIONES
MODELO
CH50EB/CH66EB (ST)
CH55EB (ST)/CH50EA (ST)
CH62EA (ST)
CH78EC (ST) CH78EB (C)
Tamaño del motor
(ml)
22 24 22
Bujía
NGK BPM-6A o BPMR-6A
Champion CJ-8Y o RCJ-8Y
NGK BPM-6A o BPMR-6A
Champion CJ-8Y o RCJ-8Y
NGK BPM-6A o BPMR-6A
Champion CJ-8Y o RCJ-8Y
Capacidad
del tanque de
combustible (l)
0,35 0,35 0,35
Peso en vacío (kg)
CH50EB .......................... 4,1
CH55EB (ST) .................. 4,5
CH66EB (ST) .................. 5,0
CH50EA (ST) .................. 4,3
CH62EA (ST) .................. 4,6
5,3 5,2
Largo total de la
cortadora (mm)
CH50EA (ST)/CH50EB
...... 500
CH66EB (ST) .................. 650
CH55EB (ST) .................. 550
CH62EA (ST) .................. 620
770 770
:
Tipo de hoja
:
△△
Nivel de presión de
sonido
LpA (dB(A))
(EN 27917)
CH50EB ....................... 100,0
CH66EB (ST) .................. 92,1
CH55EB (ST) .................. 93,6
CH50EA (ST)/CH62EA (ST)
..... 97,0
91,1 91,4
Nivel de potencia de
sonido
LwA (dB(A))
(2000/14/EC)
104 104 104
Nivel de vibración (m/s
2
) (ISO 7916)
Manija frontal
Manija posterior
CH66EB (ST) ..................
4,5
CH50EB ..........................
5,3
CH55EB (ST) ..................
4,2
CH50EA (ST)/CH62EA (ST)
.......
5,1/6,5
CH66EB (ST) ..................
5,2
CH50EB ..........................
11, 5
CH55EB (ST) ..................
12,3
CH50EA (ST)/CH62EA (ST)
.......
11, 3/9,2
7,6
6,2
3,5
5,3
NOTA
Los niveles de ruido/vibracn equivalentes se calculan como la enera ponderada en tiempo en varias condiciones de trabajo con la
distribucn de tiempo siguiente: 1/2 de ralentí, 1/2 de velocidad de aceleracn al máximo.
* Todos los datos están sujetos a cambio sin previo aviso.
49
Español
MODELO
CH78EC (SC)
CH78EC (C)
CH105EC (C)
CH66ED (TP)
CH78ED (TP)
CH78ED (CP)
Tamaño del motor
(ml)
24 24 24
Bujía
NGK BPM-6A o BPMR-6A
Champion CJ-8Y o RCJ-8Y
NGK BPM-6A o BPMR-6A
Champion CJ-8Y o RCJ-8Y
NGK BPM-6A o BPMR-6A
Champion CJ-8Y o RCJ-8Y
Capacidad
del tanque de
combustible (l)
0,35
0,33 0,33
Peso en vacío (kg)
CH78EC (SC) ........ 5,2
CH78EC (C) ..........5,2
CH105EC (C) ........5,6
CH66ED (TP) ...........5,3
CH78ED (TP) ...........5,6
5,6
Largo total de la
cortadora (mm)
CH78EC (SC) ........ 770
CH78EC (C) ..........770
CH105EC (C) ........1000
CH66ED (TP) .......... 650
CH78ED (TP) .......... 770
770
:
Tipo de hoja
:
Nivel de presión de
sonido
LpA (dB(A))
(EN 27917)
CH78EC (SC) ........ 93,9
CH78EC (C)
CH105EC (C) ........96,7/96,7
98,3 98,3
Nivel de potencia de
sonido
LwA (dB(A))
(2000/14/EC)
104 104 104
Nivel de vibración (m/s
2
) (ISO 7916)
Manija frontal
Manija posterior
CH78EC (SC) ........ 4,7
CH78EC (C)
CH105EC (C) ........6,8
CH78EC (SC) ........ 6,4
CH78EC (C)
CH105EC (C) ........5,6
CH66ED (TP) ...........8,9
CH78ED (TP) ...........7,8
CH66ED (TP) ...........6,3
CH78ED (TP) ...........5,3
6,1
11,1
NOTA
Los niveles de ruido/vibracn equivalentes se calculan como la enera ponderada en tiempo en varias condiciones de trabajo con la
distribucn de tiempo siguiente: 1/2 de ralentí, 1/2 de velocidad de aceleracn al máximo.
* Todos los datos están sujetos a cambio sin previo aviso.
56
Português
DADOS TÉCNICOS
MODELO
CH50EB/CH66EB (ST)
CH55EB (ST)/CH50EA (ST)
CH62EA (ST)
CH78EC (ST) CH78EB (C)
Cilindrada (ml) 22 24 22
Vela de ignição
NGK BPM-6A ou BPMR-6A
Champion CJ-8Y ou RCJ-8Y
NGK BPM-6A ou BPMR-6A
Champion CJ-8Y ou RCJ-8Y
NGK BPM-6A ou BPMR-6A
Champion CJ-8Y ou RCJ-8Y
Capacidade
do depósito de
combustível (l)
0,35 0,35 0,35
Peso em seco (kg)
CH50EB .......................... 4,1
CH55EB (ST) .................. 4,5
CH66EB (ST) .................. 5,0
CH50EA (ST) .................. 4,3
CH62EA (ST) .................. 4,6
5,3 5,2
Comprimento total da
tesoura (mm)
CH50EA (ST)/CH50EB
...... 500
CH66EB (ST) .................. 650
CH55EB (ST) .................. 550
CH62EA (ST) .................. 620
770 770
:
Tipo de lâmina
:
△△
vel de pressão
acústica
LpA (dB(A))
segundo (EN 27917)
CH50EB ....................... 100,0
CH66EB (ST) .................. 92,1
CH55EB (ST) .................. 93,6
CH50EA (ST)/CH62EA (ST)
..... 97,0
91,1 91,4
vel de poncia
acústica
LwA (dB(A))
(2000/14/EC)
104 104 104
Nível de vibrações (m/s
2
) (ISO 7916)
Pega frontal
Pega traseira
CH66EB (ST) ..................
4,5
CH50EB ..........................
5,3
CH55EB (ST) ..................
4,2
CH50EA (ST)/CH62EA (ST)
.......
5,1/6,5
CH66EB (ST) ..................
5,2
CH50EB ..........................
11, 5
CH55EB (ST) ..................
12,3
CH50EA (ST)/CH62EA (ST)
.......
11, 3/9,2
7,6
6,2
3,5
5,3
ATENÇÃO
Os níveis de ruído/vibrões equivalentes foram calculados com base numa média de energia ponderada por durão dos níveis de
ruído/vibrações em diferentes condões de trabalho, com a seguinte distribuão do tempo: 1/2 ralenti, 1/2 acelerão.
* Declaramos para os devidos efeitos que o produto, aparador de sebes, modelo.
57
Português
MODELO
CH78EC (SC)
CH78EC (C)
CH105EC (C)
CH66ED (TP)
CH78ED (TP)
CH78ED (CP)
Cilindrada (ml) 24 24 24
Vela de ignição
NGK BPM-6A ou BPMR-6A
Champion CJ-8Y ou RCJ-8Y
NGK BPM-6A ou BPMR-6A
Champion CJ-8Y ou RCJ-8Y
NGK BPM-6A ou BPMR-6A
Champion CJ-8Y ou RCJ-8Y
Capacidade
do depósito de
combustível (l)
0,35
0,33 0,33
Peso em seco (kg)
CH78EC (SC) ........ 5,2
CH78EC (C) ..........5,2
CH105EC (C) ........5,6
CH66ED (TP) ...........5,3
CH78ED (TP) ...........5,6
5,6
Comprimento total da
tesoura (mm)
CH78EC (SC) ........ 770
CH78EC (C) ..........770
CH105EC (C) ........1000
CH66ED (TP) .......... 650
CH78ED (TP) .......... 770
770
:
Tipo de lâmina
:
vel de pressão
acústica
LpA (dB(A))
segundo (EN 27917)
CH78EC (SC) ........ 93,9
CH78EC (C)
CH105EC (C) ........96,7/96,7
98,3 98,3
vel de poncia
acústica
LwA (dB(A))
(2000/14/EC)
104 104 104
Nível de vibrações (m/s
2
) (ISO 7916)
Pega frontal
Pega traseira
CH78EC (SC) ........ 4,7
CH78EC (C)
CH105EC (C) ........6,8
CH78EC (SC) ........ 6,4
CH78EC (C)
CH105EC (C) ........5,6
CH66ED (TP) ...........8,9
CH78ED (TP) ...........7,8
CH66ED (TP) ...........6,3
CH78ED (TP) ...........5,3
6,1
11,1
ATENÇÃO
Os níveis de ruído/vibrões equivalentes foram calculados com base numa média de energia ponderada por durão dos níveis de
ruído/vibrações em diferentes condões de trabalho, com a seguinte distribuão do tempo: 1/2 ralenti, 1/2 acelerão.
* Declaramos para os devidos efeitos que o produto, aparador de sebes, modelo.
64
Svenska
TEKNISKA DATA
MODELL
CH50EB/CH66EB (ST)
CH55EB (ST)/CH50EA (ST)
CH62EA (ST)
CH78EC (ST) CH78EB (C)
Motorstorlek (ml) 22 24 22
Tändstift
NGK BPM-6A eller BPMR-6A
Champion CJ-8Y eller RCJ-8Y
NGK BPM-6A eller BPMR-6A
Champion CJ-8Y eller RCJ-8Y
NGK BPM-6A eller BPMR-6A
Champion CJ-8Y eller RCJ-8Y
Bränsletankens
rymd (l)
0,35 0,35 0,35
Torr vikt (kg)
CH50EB .......................... 4,1
CH55EB (ST) .................. 4,5
CH66EB (ST) .................. 5,0
CH50EA (ST) .................. 4,3
CH62EA (ST) .................. 4,6
5,3 5,2
Total klippngd (mm)
CH50EA (ST)/CH50EB
...... 500
CH66EB (ST) .................. 650
CH55EB (ST) .................. 550
CH62EA (ST) .................. 620
770 770
:
Typ av knivblad
:
△△
Ljudtrycksnivå
LpA (dB (A))
(EN 27917)
CH50EB ....................... 100,0
CH66EB (ST) .................. 92,1
CH55EB (ST) .................. 93,6
CH50EA (ST)/CH62EA (ST)
..... 97,0
91,1 91,4
Ljude ektnivå
LwA (dB(A))
(2000/14/EC)
104 104 104
Vibrationsnivå (m/s
2
) (ISO 7916)
Främre handtag
Bakre handtag
CH66EB (ST) ..................
4,5
CH50EB ..........................
5,3
CH55EB (ST) ..................
4,2
CH50EA (ST)/CH62EA (ST)
.......
5,1/6,5
CH66EB (ST) ..................
5,2
CH50EB ..........................
11, 5
CH55EB (ST) ..................
12,3
CH50EA (ST)/CH62EA (ST)
.......
11, 3/9,2
7,6
6,2
3,5
5,3
OSERVERA
Överensstämmande buller- och vibrationsnivåer har beknats som den tidsvägda totalenergin för buller- och vibrationsnivåer under
olika arbetsförllanden med följande tidsfördelning: 1/2 tomgångsvarvtal, 1/2 rusningsvarvtal.
* Rätt till ändringar förbells.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92

Hikoki CH 105EC (C) Owner's manual

Category
Power hedge trimmers
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI