American Standard 4751.732.224 Installation guide

Brand: American Standard

Model: 4751.732.224

Category: Sanitary ware

Type: Installation guide

This manual is also suitable for

KITCHEN FAUCETS

4751.732

4751.732F15

M 9 6 8 7 2 1 R E V. 1. 4

Certiﬁed to comply with ASME A112.18.1M

Plumbers' Putty or Caulking

Adjustable Wrench

Channel Locks

RECOMMENDED TOOLS

INSTALL FAUCET

INSTALL VALVE BODIES

Install LOCK NUT (1) and RUBBER WASHER (2) onto SPOUT BODY (3).

Insert SPOUT BODY (1) through hole from underside of SINK.

From under sink tighten LOCK NUT (1) to secure SPOUT.

Place RUBBER RING (4) into SPOUT ESCUTCHEON (5) and screw

ESCUTCHEON (5) onto SPOUT BODY (3) until snug against

internal stop.

Install LOCK NUT (1) and RUBBER WASHER (2) onto VALVE BODIES (3).

Insert VALVE BODY (3) through hole from underside of SINK.

From under sink tighten LOCK NUT (1) to secure VALVE BODY (3).

Insert SEAL WASHERS (6) into SPOUT BODY SUPPLY HOSES (7) and

tighten connection to VALVE BODIES (3).

Place RUBBER RING (4) into ESCUTCHEON (5) and screw

ESCUTCHEON (5) onto VALVE BODY (3) until snug against internal stop.

Phillips Screwdriver

Flat Blade Screwdriver

Installation

Instructions

CAUTION

Turn off hot and cold water

supplies before beginning.

Thank you for selecting American-Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--

please read these instructions carefully before you begin.

M 9 6 8 7 2 1 R E V. 1. 4

INSTALL HANDLES

Push ADAPTER (2) into HANDLE BASE (3) in a way that the male square on the ADAPTER (2)

ﬁts in the female 8 point star of the HANDLE (4).

Turn HANDLE STEM (1) to the off position. Push HANDLE BASE (3), ADAPTER (2) and

HANDLE (4) onto VALVE STEM (1).

Tighten HANDLE SCREW (5).

Push INDEX CAP (6) in top of HANDLE (4).

Push ADAPTER (2) into LEVER HANDLE BASE (7) in a way that the male square on the

ADAPTER (2) ﬁts in the female star of the HANDLE BASE (7).

Turn HANDLE STEM (1) to the off position. Push LEVER HANDLE BASE (7) and

ADAPTER (2) onto VALVE STEM (1).

Tighten HANDLE SCREW (6).

Check alignment, if not satisfactory aligned;

Push out ADAPTER (2) carefully.

Turn ADAPTER (2) either 45˚ or 90˚ so that male square on ADAPTER (2) catches different female square in LEVER HANDLE BASE (7).

Assemble and tighten HANDLE SCREW (6). Push INDEX CAP (8) in top of LEVER HANDLE BASE (7).

CROSS HANDLE

LEVER HANDLE

FERRULE

COUPLING NUT

MAKE WATER SUPPLY CONNECTIONS

Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE SUPPLIES (3)

or 3/8"O.D. BULL-NOSE RISERS (4). Use adjustable wrench to

tighten connections. Do not over tighten. Be careful not to kink copper

supply when bending. Use tubing cutter to cut to proper length.

NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE PURCHASED SEPARATELY.

CROSS HANDLES

LEVER HANDLES

TEST INSTALLED FAUCET

FITTING WITH SPRAY

Remove AERATOR. With handles in OFF position, turn on water supplies and check all connections for leaks.

Operate both HANDLES to ﬂush water lines thoroughly. Rotate SPOUT in both directions. Replace AERATOR.

M 9 6 8 7 2 1 R E V. 1. 4

Place SPRAY HOLDER (1) into separate hole of SINK (2) and

assemble NUT (3) onto shank from underside of SINK (2).

Feed SPRAY HOSE (1) through SPRAY HOLDER (2) and

attach COUPLING NUT (3) of HOSE (1) to HOSE ADAPTOR (4)

on valve body. Tighten COUPLING NUT (3) ﬁrmly.

FITTING WITH SPRAY

Hand tighten NUT (3).

Direct SPRAY HEAD into sink and activate SPRAY. Check HOSE connections for leaks.

Aerator may accumulate dirt causing distorted and reduced water ﬂow. Remove aerator and rinse clean.

If spout drips, operate handles several times from OFF to ON position. Do not force-handles turn only 90˚.

If faucet drips proceed as follows:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A

CLOTH WITH A COARSE SURFACE.

CARE INSTRUCTIONS:

M 9 6 8 7 2 1 R E V. 1. 4

028610-0070A

VALVE

066070-YYY0A

(2.2 GPM) AERATOR

M922881-YYY0A

(1.5 GPM) AERATOR

013311-YYY0A

INDEX BUTTON

021470-YYY0A

INDEX BUTTON

021470-YYY0A

INDEX BUTTON

918428-0070A

HANDLE SCREW

918428-0070A

HANDLE SCREW

A952026-0070A

DIVERTER

M953040-YYY0A

SPRAY HOLDER

M953668-YYY0A

HANDSPRAY & HOSE

060469-YYY220A (2.2 GPM)

SPOUT

060469-YYY150A (1.5 GPM)

SPOUT

073542-0070A

SPOUT O-RING

024220-0070A

SUPPLY NUT

042692-0070A

PORCELAIN CROSS

HANDLE

908501-YYY0A

HANDLE BASE

916503-YYY0A

HANDLE BASE

013307-YYY0A

CROSS HANDLE

M961633-YYY0A

SPOUT ESCUTCHEON

013312-YYY0A

VALVE ESCUTCHEON KIT

030258-0070A

VALVE MOUNTING KIT

M961635-0070A

HOSE & SEAL KIT

921767-0070A

COUPLING

923002-0070A

HANDLE ADAPTER

060354-YYY0A

METAL LEVER HANDLE

060353-YYY0A

PORCELAIN LEVER HANDLE

923012-0070A

CLIP

KITCHEN FAUCETS

MODEL NUMBERS

WRENCH

030258-0070A

SPOUT MOUNTING KIT

012470-YYY0A

END CAP

Replace the "YYY" with

appropriate ﬁnish code

923002-0070A

HANDLE ADAPTER

4751.732

4751.732F15

For toll-free information and answers to your questions, call:

1-800-442-1902

Weekdays 8:00 a.m. to 6:00 p.m. EST

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

IN MEXICO 01-800-839-1200

Product names listed herein are trademarks of American Standard Inc.

HOT LINE FOR HELP

002

295

224

CHROME

SATIN NICKEL

OIL RUBBED BRONZE

American Standard 4751.732.224 Installation guide

Brand: American Standard

Model: 4751.732.224

Category: Sanitary ware

Type: Installation guide

This manual is also suitable for

Download PDF

report

American Standard 4751.732.224 Installation guide

This manual is also suitable for

American Standard 4751.732.224 Installation guide

Related papers

Other documents