EverFocus EN320 Owner's manual

Brand: EverFocus

Model: EN320

Category: Cable network testers

Type: Owner's manual

EN320

7" AHD / TVI / CVBS Portable Video Test Monitor

With Li-Ion Battery

User’s Manual

Release Date: November, 2015

Safety Information

Please read before use

 Please follow local power and safety guidelines and regulations, and avoid operation of this product in

any prohibited area (e.g. Hospitals, gas stations...).

 Keep away from moisture, impact, drop, or other damages to avoid malfunctioning of the unit.

 Please avoid any dust, dirt, or liquids contacting the interfaces exposed.

 In use or during transport, please avoid excessive impact or vibration, so as not to damage the

components and cause failures.

 Pay attention to the charging status and time. If the battery overheats or charging time goes over 8

hours, please unplug the power and stop charging.

 Do not use this product in a highly humid environment. Please turn off power if any abnormality

occurs, and remove all connected cables immediately.

 Do not use this product in an oil and gas environment.

 Please do not disassemble the unit as it will avoid the product warranty.

 This product is not suitable for use in a highly electromagnetic noise environment.

 Do not operate this product with wet hands or objects.

 Please avoid using chemical cleaners on this product. Dry cloth is recommended to remove dirt,

fingerprints, and other residues on the product.

 Please use 12VDC power adapter to charge this product.

 This product is able to supply 12VDC power by connect the 5φ DC jack on CCTV camera to this product

and turn on the power switch. Some cameras with no power cord or different type DC jack, please

prepare corresponding power cable and F-M connectors.

 If the CCTV camera needs more than 12watts (>1A), please use a power adapter accordingly. This

product will automatically turn off and enter the protect mode once the DC power output over 1A .

Please remove the power cable from camera and switch the power off. The protect mode will be

released by charging this product with 12VDC input.

CONTENTS

1. Introduction ................................................................................................1

2. Main Features..............................................................................................1

3. Packing List ..................................................................................................1

4. Function Interfaces and Appearance ...........................................................2

4.1 Connectors............................................................................................ 2

4.2 Panel and Front Keys............................................................................. 3

5. Operation ....................................................................................................4

5.1 Power ON / OFF .................................................................................... 4

5.2 Buttons for Configuration ..................................................................... 4

5.3 CVBS Signal Monitor / Main Menu........................................................ 4

5.4 PTZ Controller ....................................................................................... 5

5.5 CVBS Pattern Generator........................................................................ 5

5.6 RS-485 Receiver .................................................................................... 6

5.7 VGA Signal Monitor............................................................................... 6

5.8 AHD Signal Monitor............................................................................... 7

5.9 TVI Signal Monitor................................................................................. 7

6. 12VDC Power Input /Output........................................................................8

7. Specifications...............................................................................................9

EN320

1. Introduction

EN320 AHD / TVI test monitor is designed for reliable installation and maintenance of CCTV security

camera systems. It can display AHD / TVI / CVBS / VGA signals on the LCD screen, and supports built-in PTZ

Controller, Pattern Generator, RS-485 data communication monitor, all powerful functions available with

easy and friendly user interface operations. The portability helps technicians to improve working efficiency,

and significantly save the labor cost for the CCTV security system installation and maintenance.

2. Main Features

 Removable sunshield cover to avoid light reflection

 Support AHD / TVI / CVBS / VGA video input

 PTZ protocol command receiver function for RS-485 transmission testing

 PTZ control, pan / tilt, zooms in / out the lens, adjusts the focus

 Support CVBS video looping output

 12VDC Power output for camera

 Built-in Li-ion battery

 Multi-protocol, supports more than 20 kinds such as PELCO-D or PELCO-P

3. Packing List

Please check that there is no missing item in the package before using.

 7" AHD / TVI tester

 AC Adapter / 12VDC 1A output

 Battery pack / 7.4V 5200mAh

 Removable sun-shield

 BNC cable

 DC power output cable

 Hard shell bag

 Y-shape neck strap

 User's Manual

Y-shape neck strap

Adjustable neck straps for easy adjustment with velcro.

EN320

4. Function Interfaces and Appearance

4.1 Connectors

NO.

Connector

Power switch

12VDC input / output

PTZ Control (RS-485) connector

• Left connector for RS-485 +

• Right connector for RS-485 -

CVBS signal loop output / Video test pattern output

CVBS signal input

VGA signal input

AHD signal input

TVI signal input

EN320

4.2 Panel and Front Keys

NO.

Item Name

Charge indicator

• Normal:

LED off

• Charging:

LED flash

• 12VDC output:

LED on

Keyboard

7" LCD monitor

Operations of Keyboard

Button

Symbol

Function

NAVI / ENTER

OSD operation.

MODE

Switch main functions.

(PTZ Control / AHD / TVI / VGA / CVBS)

Button

Symbol

Hot-Keys

PTZ Controller mode

FAR

Enter CVBS video detect

mode.

Focus far.

NEAR

Enter AHD video detect

mode.

Focus near.

TELE

Enter TVI video detect mode.

Zoom in.

WIDE

Enter VGA video detect

mode.

Zoom out.

NOTE: Focus far / near and zoom in / out function only works in PTZ Controller mode. In other

detect mode, FAR, NEAR, TELE and WIDE are hot-keys to switch between modes.

EN320

5. Operation

5.1 Power ON / OFF

Switch to proper position to turn ON / OFF power. Toggle the power switch to panel side for power OFF;

the other side for power ON.

5.2 Buttons for Configuration

1. Press MODE to switch main functions among:

 CVBS signal monitor

 PTZ Controller

 CVBS pattern generator

 RS-485 receiver

 VGA signal monitor

 AHD signal monitor

 TVI signal monitor

2. Press in each main function to bring up the OSD sub menu. Use navigation keys to select items

and configure parameters accordingly.

Note: All parameters will be memorized automatically.

5.3 CVBS Signal Monitor / Main Menu

Connect the camera signal via BNC connector; the video

image will be displayed on the LCD panel.

Press to bring up the sub menu. The current signal

format (NTSC / PAL) will be displayed on the mode bar.

Use navigation keys to setup image parameters for

Contrast, Brightness, Color, Language, Aspect Ratio,

Mode Bar Display and Reset setting.

EN320

5.4 PTZ Controller

Connect the data cable of RS-485 to EN320. When the

camera is successfully connected, the video image will

be displayed on the LCD panel. Use navigation keys to

remotely control the directions and angles of PTZ

camera, or use FAR / NEAR / TELE / WIDE function keys

to control the camera function.

Press to bring up the sub menu, and use navigation

keys to setup Address / Protocol / Baud / S-PS / C-PS /

Pan Speed / Tilt Speed, and select video source from PTZ

Input Signal.

Set Preset Position

Use navigation keys to move to the desired position, then press to bring up the sub menu and go

to S-PS to select a preset number. When finished, press to save the setting.

Call Preset Position

Press to bring up the sub menu and go to C-PS to select a preset number. Press to force the

PTZ camera to the preset position.

5.5 CVBS Pattern Generator

When switch to this function, the pattern generator will

turn on automatically and output a color-bar pattern via

BNC video output port. Connect this pattern to the cable

to check if the signal cable in camera end to DVR is

installed properly.

Press to bring up the submenu and switch NTSC /

PAL signal format by navigation keys.

EN320

5.6 RS-485 Receiver

Once the PTZ device is connected, the Data Monitor is

able to capture the protocol from the controlling system

and display command data. It is helpful to debug and

maintain RS-485 communication.

Press and keys to switch Baud rate.

5.7 VGA Signal Monitor

Connect the signal via VGA connector and the video

image will be displayed on the LCD panel.

Press to bring up the sub menu. Use navigation keys

to setup image parameters for Auto Adjust, Contrast,

Brightness and Color.

EN320

5.8 AHD Signal Monitor

Connect the camera signal via AHD connector and the

video image will be displayed on the LCD panel.

Press to bring up the sub menu. Use navigation keys

to setup image parameters for Contrast, Brightness,

Color, Gamma, Color Temperature, Aspect Ratio and

Blue Only.

5.9 TVI Signal Monitor

Connect the camera signal via TVI connector and the

video image will be displayed on the LCD panel.

Press to bring up the sub menu. Use navigation keys

to setup image parameters for Contrast, Brightness,

Color, Gamma, Color Temperature, Aspect Ratio and

Blue Only.

EN320

6. 12VDC Power Input /Output

The charging port of EN320 also has power output function. When the camera is installed but power is not

ready yet, it is able to supply 12VDC (1A) power for a CCTV security camera, and will help to confirm the

signal camera is installed properly with correct position and angle.

EN320

7. Specifications

Model

EN320

Display

Display Resolution (H) x (V)

1024 x (R.G.B) x 600

Active Area (W) x (H)

153.6 x 90.0mm

Dot Pitch (W) x (H)

0.05 x 0.15mm

Brightness

500cd/m²

Contrast Ratio

700 : 1

Response

10ms

Video

Input

AHD

720p / 1080p

TVI

720p / 1080p

VGA

VGA (640 x 480) ~ UXGA (1600 x 1200)

CVBS

NTSC / PAL 1.0Vp-p

Output

CVBS

Thru Output & Pattern Out

Power

Input

12VDC (Exclusive Adaptor)

Output

≒ 12VDC (1A)

PTZ Controller

Protocol

EverFocus, PELCO-D, PELCO-P, Yaan, Yaan-0, Samsung, LilinF, LilinM,

Molyax, Minking, AD, Fastrax, CBC, SONY-EVI, LG-MUL, DAT-SD,

Pearmain, Vicon, Vcltp, DHYTC06, SANYO, BOSCH

General

Operation Setting

Chinese / English OSD menu

Mode Bar Display

Display / No Display (After 5 seconds)

Power Adapter

12VDC (1A)

Battery

Built-in 7.4V Li-Ion, 5200mAh

Rechargeable

After charging 4 hours, working time lasts 5-7 hours

Working Temperature

0°C ~ 50°C / 32°F ~ 122°F

Working Humidity

0% ~ 80%

Dimensions (W) x (H) x (D)

250 x 158 x 50 mm / 9.84" x 6.22" x 1.97"

Weight

940g / 2.07lb

EverFocus Electronics Corp.

EverFocus Taiwan:

12F, No. 79, Sec. 1, Shin-Tai Wu Rd.,

Hsi-Chih, New Taipei City, Taiwan

TEL: +886 2 2698 2334

FAX: +886 2 2698 3943

www.everfocus.com.tw

[email protected].tw

EverFocus Europe - Germany:

Albert-Einstein-Strasse 1, D-46446

Emmerich, Germany

TEL: +49 2822 93940

FAX: +49 2822 939495

www.everfocus.de

sales@everfocus.de

EverFocus China - Beijing:

Room 609, Technology Trade Building,

Shangdi Information Industry Base,

Haidian District, Beijing 100085, China

TEL: +86 10 6297 3336~39

FAX: +86 10 6297 1423

www.everfocus.com.cn

[email protected]

EverFocus China - Shenzhen:

4F, No. 2, D4 Building, Wan Yelong

Industrial Park, Tangtou Road, Shiyan,

Baoan, Shenzhen, Guangdong 518101, China

TEL: +86 755 2765 1313

FAX: +86 755 2765 0337

www.everfocus.com.cn

[email protected]

EverFocus USA - California:

1801 Highland Avenue, Unit A, Duarte, CA

91010, USA

TEL: +1 626 844 8888

FAX: +1 626 844 8838

www.everfocus.com

[email protected]

EverFocus Japan:

3F, Kuramochi, Building II,

2-2-3 Koto-Bashi,Sumida-Ku,

Tokyo, 130-0022, Japan

TEL: +81 3 5625 8188

FAX: +81 3 5625 8189

www.everfocus.co.jp

[email protected]

Your EverFocus product is designed and

manufactured with high quality

materials and components which can be

recycled and reused.

This symbol means that electrical and

electronic equipment, at their

end-of-life, should be disposed of

separately from your household waste.

Please, dispose of this equipment at

your local community waste

collection/recycling centre.

In the European Union there are

separate collection systems for used

electrical and electronic product.

Please, help us to conserve the

environment we live in!

Ihr EverFocus Produkt wurde entwickelt

und hergestellt mit qualitativ

hochwertigen Materialien und

Komponenten, die recycelt und wieder

verwendet werden können.

Dieses Symbol bedeutet, dass elektrische

und elektronische Geräte am Ende ihrer

Nutzungsdauer vom Hausmüll getrennt

entsorgt werden sollen.

Bitte entsorgen Sie dieses Gerät bei Ihrer

örtlichen kommunalen Sammelstelle oder

im Recycling Centre.

Helfen Sie uns bitte, die Umwelt zu

erhalten, in der wir leben!

EverFocus EN320 Owner's manual

Brand: EverFocus

Model: EN320

Category: Cable network testers

Type: Owner's manual

Download PDF

report

EverFocus EN320 Owner's manual

EverFocus EN320 Owner's manual

Related papers

Other documents