Crown Automotive RT24001 Installation guide

Brand
Crown Automotive
Model
RT24001
Type
Installation guide

Crown Automotive RT24001 is a versatile tool that can be used for a variety of tasks, including:

  • Installing a new transmission oil pan: The RT24001 can be used to remove the old transmission oil pan and install a new one. This is a relatively simple task that can be completed in about an hour.
  • Changing the transmission filter: The RT24001 can also be used to change the transmission filter. This is a more involved task, but it is still something that can be completed in a few hours.
  • Checking the transmission fluid level: The RT24001 can be used to check the transmission fluid level. This is a quick and easy task that can be completed in just a few minutes.

Crown Automotive RT24001 is a versatile tool that can be used for a variety of tasks, including:

  • Installing a new transmission oil pan: The RT24001 can be used to remove the old transmission oil pan and install a new one. This is a relatively simple task that can be completed in about an hour.
  • Changing the transmission filter: The RT24001 can also be used to change the transmission filter. This is a more involved task, but it is still something that can be completed in a few hours.
  • Checking the transmission fluid level: The RT24001 can be used to check the transmission fluid level. This is a quick and easy task that can be completed in just a few minutes.
Crown Automotive Sales Co., Inc.
Installation Instructions for A904, A999 Deep Transmission Oil Pan
1- Before beginning, purchase 5 quarts of the recommended Transmission Fluid. Typically, a filter change uses 4
quarts, so allow for the extra volume of the new pan.
2- Allow the vehicle to cool completely. Chock the front and rear wheels and lift the vehicle, setting it securely on
jack stands.
3- If the transmission pan has a drain plug remove it, allowing for all the fluid to drain out into an appropriately sized
drain pan. Once the fluid stops draining, loosen all the hardware about 3 turns and ensure the pan is free from the
housing. Remove the rest of the hardware, place the pan aside and keep the hardware.
4- If the transmission does not have a drain plug then
loosen all the hardware about 3 turns and ensure the
pan is free from the housing with a putty knife or
something similar that will not damage the housing.
Then remove all the bolts except for 2 on one side,
which should allow the pan to tilt and drain the fluid
out in a predictable fashion. Once the maximum
amount of fluid has been drained remove the rest of the
hardware and place the pan aside and keeping the
hardware.
5- Clean the mating surface on the transmission with a
razor blade and some parts cleaner to remove all traces
of the old gasket and sealant.
6- Remove the old filter from the Valve Body by removing the three screws. With the washers installed on the screws
provided, slide the screws through the holes in the new filter and slide the new pick-up spacer onto the screws with
the o-ring side up. Install this assembly onto the valve body and install the screws. Torque the screws to 35 In.
Lbs.
7- Attach the new Gasket and Pan to the transmission using the factory hardware, ensuring that the gasket aligns
correctly and does not rip. Then torque the hardware to 150 In. Lbs and tread the drain plug into the transmission
pan and torque to 25 Ft. Lbs.
8- Lower the vehicle to the ground and add enough transmission fluid so that it registers on the dip stick. (be aware
that after pouring transmission fluid down the dip stick tube that it will be inaccurate for a few minutes due to the
fluid on the walls of the tube)
9- Start the vehicle and place it in neutral. Allow the vehicle to get up to its optimal operating temperature.
10- Cycle the transmission shifter a few times, keeping it in each gear for 10-15 seconds and place the vehicle in
neutral once again.
11- Check fluid again and add if necessary in order to get it to the recommended level.
12- Check the vehicle for leaks and ensure that the fluid is at the recommended level after each of the first few trips
(remember, it has to be in neutral when checking) and re-torque the transmission pan bolts and drain plug after 100
and 500 miles.
While every attempt is made to ensure that the information contained in these instructions is correct, no liability can be accepted by the authors for loss, damage, or injury
caused by any errors in, or omissions from the information given. All service should be performed by qualified mechanics. Crown Automotive Sales Co .,Inc. cannot be held
responsible for any mechanical work performed. Standard and accepted safety precautions should be used in every procedure.
  • Page 1 1

Crown Automotive RT24001 Installation guide

Brand
Crown Automotive
Model
RT24001
Type
Installation guide

Crown Automotive RT24001 is a versatile tool that can be used for a variety of tasks, including:

  • Installing a new transmission oil pan: The RT24001 can be used to remove the old transmission oil pan and install a new one. This is a relatively simple task that can be completed in about an hour.
  • Changing the transmission filter: The RT24001 can also be used to change the transmission filter. This is a more involved task, but it is still something that can be completed in a few hours.
  • Checking the transmission fluid level: The RT24001 can be used to check the transmission fluid level. This is a quick and easy task that can be completed in just a few minutes.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents