Martec MNF143WOR Operating instructions

Martec
Brand
Martec
Model
MNF143WOR
Type
Operating instructions

This manual is also suitable for

E: [email protected] | P: 02 8778 7500
www.martecaustralia.com.au
NEWPORT Series Installation Guide
Models Parameters (Fan Only):-
MNF143WWR 1420mm 3 Blade Ceiling Fan White Satin with Remote Control
MNF143MMR
MNF143OWR
MNF143WOR
1420mm 3 Blade Ceiling Fan Matt Black with Remote Control
1420mm 3 Blade Ceiling Fan Old Bronze/Walnut with Remote Control
1420MM 3 Blade Ceiling Fan White Satin/Oak with Remote Control
Models Parameters (Fan and Light):-
MNF1433WWR 1420mm 3 Blade Ceiling Fan White Satin, 15W Tricolour LED Light with Remote Control
MNF1433MMR
MNF1433OWR
MNF1433WOR
1420mm 3 Blade Ceiling Fan Matt Black, 15W Tricolour LED Light with Remote Control
1420mm 3 Blade Ceiling Fan Old Bronze/Walnut, 15W Tricolour LED Light with Remote Control
1420mm 3 Blade Ceiling Fan White Satin/Oak, 15W Tricolour LED Light with Remote Control
Part List:
Qty 1x motor assembly Qty 1x instruction manual Qty 1x screw kit Qty 1x balancing kit
Qty 1x hanging bracket Qty 1x remote control kit Qty 3x blades
How to Assemble
Secure the hanger bracket
to ceiling beam or a suitable
piece of timber inserted
between the ceiling beams
using the two long screws
supplied with the package.
Place circular shockproof
gasket above the hanger
bracket. Align the bracket
and screw the hanger
bracket to the ceiling tightly.
Place fan into hanger
bracket and align Ball Joint
Slot with hanger bracket as
illustrated.
After wiring is completed,
attach the canopy to the
hanger bracket by pushing
upwards and twisting anti-
clockwise. Tighten screws
and ensure canopy is not
touching the ball joint.
Fg.1 Fg.2 Fg.3 Fg.4
Thanks for choosing our Newport DC Series ceiling fan.
We strongly recommend that you read this manual carefully before installation.
Application
Flat Surface / Ceiling Slope Ceiling up to 10° Corrugated Ceiling Apex Ceiling
E: [email protected] | P: 02 8778 7500
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
How to Install Blades
Attach the blade to the top of the motor using the 4 blade
screws provided. Tighten the screws and repeat this
procedure for all blades.
Fg.6
To install align the blades with the orice as shown.
Fg.5
How to Install / Remove the Plastic Shade
To remove - turn the plastic shade anti-clockwise.
To install - The plastic shade buckle is pushed up to the long
hole on the light plate, spin the plastic shade clockwise.
Fg.7
CCT (Colour Changeable Temperature)
Choose colour temperature by licking the switch in the LED
C = 5000K cool white
N = 4000K neutral white
W = 3000K warm white
Fg.8
1
2
3
mounting plate
------------------------------------------------------
AC POWAER INPUT
ki
LIGHT
TO FAN W
M
IO
RT
ES
OR
L N
yellow green
black blue brownb lack
brown blue green
4P
plug
yellow green
AC IN L
AC IN N
brown
blue
yellow green
3P
E: [email protected] | P: 02 8778 7500
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
Instructions and Functions of Transmitter
1. LED indicator light
2. Light ON/OFF
(Use to dim light within 1s)
3. Speed of the fan
(1 high speed - 5 low speed)
4. Timing control of the fan
5. Direction of the fan
(reverse switch)
6. Fan ON/OFF
7. 12v battery to be used
in transmitter
1. LED indicator light
2. Speed of the fan
(1 high speed - 5 low speed)
3. Timing control of the fan
4. Direction of the fan
(reverse switch)
5. Fan ON/OFF
6. 12v battery to be used in
transmitter
Installing Receiver Remote Control
Important Reminders
• Receiver must be correctly installed in the mounting bracket
• When the transmitter cannot control the receiver, please check
i) has sucient battery in the transmitter
ii) any existence of similar remote controlled products nearby that cause interference
•Replace battery if getting low as this will aect sensitivity of the transmitter
• Take the battery out from the transmitter when leaving used for a long time to avoid battery leaks
• Support up to 200W lighting power
• Isolation switch MUST be connected in the line
• Dimming switch on the light models is operated by tuning the light ON/OFF button within 1s. Light output will dim
in stages from 18W to 8W to 2W approximately
Fan Only Model Fan LED Light Model
Fan Only Model Fan LED Light Model
yellow green
OUTPUT
to the FAN MOTOR
black
blue
black
blue
brown
to the FAN LIGHT
LIGNT
FOR LIGHT N
FOR LIGHT L
FOR FOR
MOTOR
TO MOTOR
TO MOTOR
TO MOTOR
to AC Power
AC IN L brown
AC IN N blue
yellow green
L N
ACINPUT
4P plug
to AC Power
E: [email protected] | P: 02 8778 7500
www.martecaustralia.com.au
Wire Connections
WARNING
• Installation of fans MUST follow SAA standards and meet local authority regulations.
• Installation MUST be carried out by a qualied and licensed electrician.
• Fan and light MUST be earthed.
• Bracket MUST be rmly attached to a at solid structure or timber frame.
• DO NOT mix blades from one model to another, all blades MUST be replaced if damaged.
• The warranty is VOID if product is not installed according to this installation guide.
6* Year Warranty
Visit our website for details https://www.martecaustralia.com.au/warranty-statement/
Fan LED Light ModelFan Only Model
yellow green
black
plug
plug
yellow green
2P
4P
black
blue
FOR LIGHT L
FOR LIGHT N
Motor
black
TO MOTOR brown
blue
TO MOTOR
TO MOTOR
black
blue
yellow green
brown
brown
blue
blue
FOR LIGHT L black
FOR LIGHT N
black
TO MOTOR brown
blue
TO MOTOR
TO MOTOR
yellow green
to the FAN MOTOR
to the FAN LIGHT
3P
2P
AC IN N
AC IN L
yellow green
yellow green
black
blue
brown
to the FAN MOTOR
TO MOTOR
TO MOTOR
TO MOTOR
to the FAN LIGHT
black
blue FOR LIGHT N
FOR LIGHT L
LIGNT MOTOR
L N
ACINPUT
FOR FOR
OUTPUT
yellow green
black
brown
blue
blue
brown
4P plug
to AC Power
yellow green black
brown blue
yellow green
brown
blue
AC N
AC L
L N
240 Vac SUPPLY
Motor
yellow green
black
TO MOTORbrown
blue
TO MOTOR
TO MOTOR
to AC Power
AC IN N
AC IN L
yellow green
black
TO MOTOR
4P plug
brown
blue
TO MOTOR
TO MOTOR
black blue brown
black
yellow green
to the FAN MOTOR
3P
3P
yellow green
brown blue green
1P
yellow green
N L
AC POWAER INPUT
receiver of
remote control
blue
brown
4P plug yellow green
black
brown
blue
240 Vac SUPPLY
AC N
AC L
L N
L N MOTOR
LIGHT
TO FAN WIRES
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Martec MNF143WOR Operating instructions

Martec
Brand
Martec
Model
MNF143WOR
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents