Westinghouse 7706100 Operating instructions

Westinghouse
Brand
Westinghouse
Model
7706100
Type
Operating instructions

Westinghouse 7706100 is a ceiling fan bracket designed to provide a secure and stable mounting platform for ceiling fans and fixtures. It features a sturdy black bracket that attaches to the ceiling fan box using 11⁄2" machine screws, flat washers, and lock washers. The bracket has a retaining ball socket that accommodates a down rod, which is secured with a 1⁄2" set screw. The bracket also includes a green grounding wire that connects to the grounding conductor in the ceiling fan box for added safety.

Westinghouse 7706100 is a ceiling fan bracket designed to provide a secure and stable mounting platform for ceiling fans and fixtures. It features a sturdy black bracket that attaches to the ceiling fan box using 11⁄2" machine screws, flat washers, and lock washers. The bracket has a retaining ball socket that accommodates a down rod, which is secured with a 1⁄2" set screw. The bracket also includes a green grounding wire that connects to the grounding conductor in the ceiling fan box for added safety.

Westinghouse Lighting Corp.
Philadelphia, PA 19154-1099, U.S.A.
is a registered trademark of
Westinghouse Electric Corporation
Made in Taiwan / Hecho en Taiwán
© 2002 WESTINGHOUSE LIGHTING CORP.
77061
Install and use this product following your local electrical codes and regulations.
1. Turn off current at fuse or circuit breaker.
2.
Place rubber washers between ceiling fan box and black bracket.
Align holes and secure bracket to
box using 1
1
⁄2" machine screws, flat washers and lock washers supplied. (Fig. A)
3.
Place retaining ball into socket of bracket matching key to slot in retaining ball.
4.
Slide down rod through bottom of retaining ball and insert pin
through down rod. (Fig. B) Lock pin into
retaining ball slots and secure with
1
⁄2" set screw. (Fig. C)
5.
Connect green grounding wire of retaining ball to grounding conductor in ceiling fan box.
6. Slide canopy over down rod.
7.
Complete fan or fixture installation
following manufacturer’s instructions.
8.
Slide wires from fan or fixture through down rod and make proper connections in ceiling box.
9.
Place canopy into proper position over black bracket and secure with
1
⁄2" screws. (Fig.B)
Warning: Do not mount fan to existing ceiling box. The box must comply with the requirements of the
National Electric Code.
Use Westinghouse Fan Brace
®
Support Products for all your installation needs.
Install
ceiling fan box following manufacturer’s instructions.
Instale y use este producto siguiendo los códigos y reglamentos de electricidad locales.
1.
Apague la corriente eléctrica en el fusible ó el corta-circuitos.
2.
Coloque las arandelas entre la caja del ventilador de techo y el soporte negro.
Alinee los huecos y sujete
el soporte a la caja usando tornillos de 1
1
⁄2" arandelas llanas y de seguridad provistas. (Fig. A)
3.
Coloque la bola retenedora en la cuenca del soporte poniendo la llave en la ranura corres-pondiente en
la bola de retención.
4. Deslize la varilla descendente por el fondo de la bola de retención y entre las clavijas por la varilla
descendente. (Fig. B) Sujete la clavija en las ranuras en la bola de retención y sujete con los tornillos de
fijación de
1
⁄2". (Fig. C)
5.
Conecte el cable verde de conectar a tierra de la bola de retención al conductor de conectar a tierra en la
caja del ventilador de techo.
6. Deslize el dosel sobre la varilla descendente.
7.
T
ermine la instalación del adorno o el ventilador siguiendo las instrucciones del fabricante.
8.
Deslize los cables del ventilador ó adorno por la varilla descendiente y haga las conexiones
adecuadas en la caja de empalme.
9.
Coloque el dosel en la posición adecuada sobre el soporte negro y sujete con los
tornillos de
1
⁄2". (Fig.B)
Advertencia: No monte el ventilador a la caja existente en el techo. La caja debe cumplir con todos los
requisitos de los Codigos Nacionales de Electricidad.
Use los productos 'Fan Brace Support' marca
Westinghouse en todas sus necesidades de instalación
.
Instale la caja de ventilador de techo siguiendo las
instrucciones del fabricante.
Fig. A
Fig. B
Fig. C
  • Page 1 1

Westinghouse 7706100 Operating instructions

Westinghouse
Brand
Westinghouse
Model
7706100
Type
Operating instructions

Westinghouse 7706100 is a ceiling fan bracket designed to provide a secure and stable mounting platform for ceiling fans and fixtures. It features a sturdy black bracket that attaches to the ceiling fan box using 11⁄2" machine screws, flat washers, and lock washers. The bracket has a retaining ball socket that accommodates a down rod, which is secured with a 1⁄2" set screw. The bracket also includes a green grounding wire that connects to the grounding conductor in the ceiling fan box for added safety.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents