Beltronics Beltronics GT-360 Owner's manual

Brand: Beltronics

Model: Beltronics GT-360

Category: Radar detectors

Type: Owner's manual

This manual is also suitable for

GT-360

Escort Beltronics GT-360 is an advanced radar and laser detector that provides 360-degree protection against speed traps, red light cameras, and other threats. Its high-definition performance accurately identifies real threats sooner and the threat direction arrows show you where they are. The updatable IVT Filter reduces false alerts from moving In-Vehicle Technology sources, and the GPS location-based intelligence automatically locks out false alerts and lets you mark locations for future reference.

Programming

Press BRT to go from Press VOLUME + or – to change

one category to the next your setting within a category

User Mode Advanced* Access and customize all Settings and Preferences

Novice Access and customize units and display color, (all other

Settings are set to factory defaults)

NOTE: Switch back to Advance mode to view all Preferences

Pilot Scan Bar* Scanning Bar with Full Word

Full Word Full Word: AutoScan, Auto NoX, or Highway

Display Color Copper*/Blue/Green/Red Set color to match your vehicle’s dash display

Speed Display On* Displays current speed

O Displays battery voltage

Cruise Alert O / 20-160 mph Oers double beep alert tones below specied speed

20 mph*

Over Speed O / 20-160 mph Reminds you when you exceed a specied speed

70 mph*

Meter Mode Standard* Single band with front and rear signal strength bar graphs

Tech Single band with numeric frequency and front and rear

signal strength bar graphs

Basic Simple messages replace bands:

Caution (if traveling below cruise alert limit)

Slow Down (if traveling above cruise alert limit)

Tones Standard* Standard Beltronics alert tones

Mild Mild doorbell chime alert tones

AutoMute Low/Med*/High/O

Automatically reduces audio to preferred volume during alert

AutoLock On* / O Automatically stores and locks out false alarms

Units English*/Metric Units for distance and speed

Language English*/Espanol Language for voice and text

Voice On* / O Voice announcements

GPS Filter On* / O Enables GPS-powered features

Press and hold the BRT and SEN buttons to access Programming. To exit Programming, simply wait a few

seconds without pressing a button. The unit will display Completed to conrm your selections.

Programming

AutoPower O Power turns on or o depending on your vehicle’s ignition

type (constant power or switched)

1 Hour Powers o automatically after 1 hour

2 Hours Powers o automatically after 2 hours

4 Hours* Powers o automatically after 4 hours

8 Hours Powers o automatically after 8 hours

NOTE: If AutoPower is on, to save screen life the display screen goes

blank after 30 minutes without moving.

Band Enables Default* Default Settings

Modied Band Enables have been modied from their default settings

Press SEN to go from one Press VOLUME + or – to change

band category to the next your setting within a category

X Band On* / O

K Band On* / O Freq: 24.050-24.250 GHz

NOTE: When K Band is o, you can select separate segments of the

band to turn on or o.

KN1 On* / O Freq: 24.050 - 24.110 GHz

KN2 On* / O Freq: 24.110 - 24.175 GHz

KN3 On* / O Freq: 24.175 - 24.250 GHz

KN4 On / O* Freq: 23.950 - 24.050 GHz

Ka Band On* / O Freq: 33.400-36.000 GHz

NOTE: When Ka Band is o, you can select separate segments of the band to turn

on or o.

KaN1 On / O* Freq: 33.400 - 33.700 GHz KaN6 On / O*

Freq: 34.800 - 35.160 GHz

KaN2 On / O* Freq: 33.700 - 33.900 GHz KaN7 On / O*

Freq: 35.160 - 35.400 GHz

KaN3 On* / O Freq: 33.900 - 34.200 GHz KaN8 On* / O

Freq: 35.400 - 35.600 GHz

KaN4 On* / O Freq: 34.200 - 34.600 GHz KaN9 On / O*

Freq: 35.600 - 35.840 GHz

KaN5 On* / O Freq: 34.600 - 34.800 GHz KaN10 On / O*

Freq: 35.840 - 36.000 GHz

Ka Band On* / O

Ka-POP On / O*

Laser On* / O

TSR On* / O Automatically rejects trac ow sensors-monitoring false alarms

Marker Enable On* / O Default Settings

Modied Marker Enables have been modied from their default settings

NOTE:

AutoPower only

works with constant

power ignition

Programming

Press SEN to go from one Press VOLUME + or – to change

marker category to the next your setting within a category

Other On* / O Other location

Redlight On* / O Red light camera

Red & Speed On* / O Red light & speed camera

Speed Cam On* / O Speed camera

Air Patrol On / O* Known aircraft patrolled areas

NOTE: User cannot mark an air patrol location

Speed Trap On* / O Speed trap

Air Patrol On / O* Known aircraft patroled areas

NOTE: User cannot mark an Air Patrol location

Clear Locations Marked Clear all user Marked locations. Press SEN button to conrm

Lockouts Clear all lockouts. Press SEN button to conrm

Defender Clear all DEFENDER data. Press SEN button to conrm

Format Clear DEFENDER database, all markers, and all lockouts.

Press SEN button to conrm

*Default Setting

Beltronics USA, Inc.

5442 West Chester Road, West Chester OH 45069

Beltronics One Year Limited Warranty

What this warranty covers: Beltronics USA, Inc. (“Beltronics”) warrants

your Product against all defects in materials and workmanship.

For how long: One (1) year from the date of original purchase from an

authorized Beltronics dealer.

What we will do: If a breach of warranty occurs, Beltronics, at its

discretion, will either repair or replace your Product free of charge.

What we will not do: Beltronics will not pay shipping charges that you

incur for sending your Product to us.

What you must do to maintain this warranty: Show original proof of

purchase or receipt from an authorized Beltronics dealer.

Warranty exclusions: This warranty does not apply to your product

under any of the following conditions: 1. The serial number has been

removed or modied. 2. Your product has been subjected to misuse

or damage (including water damage, physical abuse, and/or improper

installation). 3. Your product has been modified in any way. 4. Your

receipt or proof-of-purchase is from a non-authorized dealer or internet

auction site, including E-bay, U-bid, or other non-authorized resellers.

5. You are not the original purchaser of the Product from an authorized

dealer or did not receive it as a gift from the original purchaser of the

Product from an authorized dealer.

To obtain service: 1. Contact Beltronics (1-800-341-2288) to obtain

a Return Authorization Number. 2. Properly pack your Product and

include: your name, complete return address, written description of

the problem with your Product, daytime telephone number, and a

copy of the original proof of purchase or receipt. 3. Label the outside of

the package clearly with your Return Authorization Number. Ship the

Product pre-paid (insured, for your protection) to: Beltronics USA, Inc.,

5442 West Chester Rd., West Chester, OH 45069.

LIMITATION OF WARRANTY: The obligations set forth above are

Beltronics’ sole obligations and your exclusive remedy. Beltronics makes

no other express warranty. Any implied warranty of merchantability or

tness for a particular purpose that may be applicable to the Product is

limited in duration to the duration of this warranty. Some States do not

allow limitations on how long an implied warranty lasts, so the above

limitation may not apply to you. BELTRONICS SHALL NOT BE LIABLE

FOR CONSEQUENTIAL, SPECIAL OR INCIDENTAL DAMAGES INCLUDING,

WITHOUT LIMITATION, DAMAGES ARISING OUT OF THE USE, MISUSE OR

MOUNTING OF THE PRODUCT. Some States do not allow the exclusion

or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you. Beltronics is not responsible

for products lost in shipment between the owner and our service center.

Other legal rights: This warranty gives you specic legal rights, and you

may also have other rights which vary from State to State.

TrueLock™, SmartShield®, SpecDisplay™, AutoSensitivity™ and EZ Mag Mount™

are trademarks of Beltronics USA, Inc. Manufactured in the Philippines.

Features, specications and prices subject to change without notice.

FCC NOTE: Modications not expressly approved by the manufacturer could

void the user’s FCC granted authority to operate the equipment.

FCC ID:QL4M6. CONTAINS FCC ID:QKLBT2

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received including interference that

may cause undesired operation.

866.468.0322 • Beltronics.com

Notes for Programming

For descriptions of features and functions

available when connected to ESCORT Live, visit

Beltronics.com and download the GT-360 Owner’s

Manual.

To view serial number and software revision press

MRK and MUTE while powering on detector.

To restore GT-360 to its original factory Settings,

press and hold MRK and BRT while turning the

power on. A Restored message will display,

acknowledging the reset.

Software Updates

GT-360’s red light and speed camera database

is easily updated using our exclusive detector

software tools found on our web site. Firmware, or

the operating software for the detector, can also

be updated using these tools.

In order to have access to these updates, you

must register your GT-360 at www.Beltronics.

com. Once registered, you will receive email

notications that updates are now available

for your database or rmware. To handle your

software and DEFENDER updates you need to

connect your GT-360 to a computer rst. You can

connect GT-360 to a computer via USB/USB Mini

B cable.

Live life in the passing lane.

Quick Reference

Live life in the passing lane.

Arrows indicate direction of the threat.

360° Protection with Threat Direction

Dual Antenna Front

& Rear Protection

GPS Intelligence Rejects

False Alerts

ESCORT Live

Crowd Sourced Alerts

Lightning Fast

Response

GT-360

Congratulations GT-360 Features

HIGH DEFINITION 360° PROTECTION

GT-360 features a

new multi-color

OLED display.

Brilliant graphics

illuminate intuitive

icons that identify

the type of threat at

a glance.

• GT-360’s HD Performance accurately identies

real threats sooner than other detectors, and

with threat direction arrows, provides you with

location information about these threats.

• Updatable IVT Filter™ automatically reduces

false alerts from moving In-Vehicle Technology

sources such as collision avoidance systems and

adaptive cruise control.

• GPS location-based intelligence automatically

locks out false alerts and allows you to mark

locations for future reference.

• Access to the DEFENDER Database, which warns

you of veried speed traps, speed cameras, and

red light cameras.

• Built in Bluetooth® technology gives you access

to ESCORT’s award winning app, ESCORT Live.

The exclusive real-time ticket-protection

network which warns you of upcoming alerts

received and reported by other users in the

area, and gives you access to local speed limit

data for over-speed alerts.

Take the freedom of the road back with the

Beltronics GT-360, equipped with 360° high

denition protection, threat direction arrows, and

intelligent GPS technology to eliminate false

alerts.

Go to Beltronics.com for full featured Owner’s

Manual.

Registration and ESCORT Live

For iPhone:

1 Ensure GT-360 power is ON

2 Open the App Store on your iPhone

and search for ESCORT Live Radar.

3 Follow the onscreen instructions to download

ESCORT Live Radar and then open the app.

4 When prompted, enter the username and

password you created when registering your

product at Beltronics.com.

5 Press the Settings button then select

Devices.

6 You should see GT-360

listed with Not Connected

underneath.

Press the

GT-360 device

entry and when prompted

select Pair.

7 The Bluetooth icon on the GT-360 display

will appear to conrm that it is paired to

your iPhone.

Before downloading ESCORT Live, you must rst

nearby, as you will need its serial number.

1 Visit www.Beltronics.com and click Product

Registration.

2 Click the “Registration for all devices” link.

3 Follow the onscreen instructions to register

your device.

Be sure to write down the username and password

you create, as you will need this information to

access and download ESCORT Live. (You will also

receive an e-mail with this information, once you

have registered your device.)

For Android based smartphones:

1 Ensure GT-360 power is ON.

2 On your smartphone go to Bluetooth® Settings

and make sure that Bluetooth® is ON.

3 Press Scan for devices and wait for the device

list to populate, GT-360 should appear

under Available devices.

4 Press the GT-360 device entry.

5 The Bluetooth icon on the GT-360 display

will appear to conrm that it is paired to your

smartphone.

Open Google Play on your smartphone

and search for Escort Live Radar.

7 Follow the onscreen instructions to download

Escort Live Radar and then open the app.

8 When prompted, enter the username and

password you created when registering your

product at Beltronics.com.

7 Open the app, walk through the tutorial, and

you’re ready to hit the road!

Installation Controls & Features

4 To adjust view, loosen thumb wheel and adjust

angle of mounting bracket. Tighten thumb wheel

to secure.

5 Tilt the display end of the detector slightly

upward and engage with the anged edge of the

mounting bracket. The EZ Mag Mount™ magnet

holds the detector in place.

6 To remove the detector, simply lift the display

end of the detector upward. The detector will

release from the mount.

7 To remove mount from windshield, release

locking clamp and pull tab on top of StickyCup.

EZ Mag Mount™ Care Instructions:

Should the EZ Mag Mount™ StickyCup accumulate

debris and lose its stickiness, simply rinse under

warm water, gently wipe o debris and allow to

air dry.

Your new detector comes with the revolutionary

EZ Mag Mount™. Simply tilt the display end of the

detector up and slide it onto the mounting

bracket. The magnetic mount holds the detector

in place. To remove the detector from the mount,

simply lift the display end of the detector and the

detector releases from the mount.

Mounting Tips:

• Center of windshield between driver and

passenger.

• Ensure clear view of road ahead and sky

above.

• Avoid windshield wipers and heavily tinted

areas.

To mount the detector in your vehicle:

1 Remove paper backing from EZ Mag Mount™ `

StickyCup.

2 Ensure the locking clamp is open.

3 Firmly press EZ Mag Mount™ StickyCup onto

windshield and close the locking clamp to secure.

Locking Clamp (closed)

Thumb Wheel For

Angle Adjustment

Mounting Bracket

Release Tab

StickyCup

GT-360

EZ Mag Mount™

Installation Controls & Features

Using GT-360

1 Plug small end of SmartCord USB into modular

jack on GT-360 and large end of SmartCord USB

into your vehicle’s lighter/accessory socket

2 GT-360 should power on automatically. If not,

press the device’s power button.

Power requirement

11.0-16.0 Volts DC negative ground

400mA standby, 700 mA maximum

NOTE: You can easily access and customize all of

your Settings and Preferences by pressing and

holding the BRT and SEN buttons. See Settings and

Preferences for details.

Using SmartCord USB

• Mute Button:

- Press to mute the audio for a specic alert.

- Press three times to lock out a false alert.

- Press twice while receiving a locked-out alert

to unlock.

- When connected to ESCORT Live press and

hold mute button on unit or cord to manually

report to other users a veried X or K-band

alert, or a police ocer observing trac.

• Alert Light: Blinks red when receiving a radar or

laser alert.

• Power Light: Lights green when device is

powered on.

• USB Charging Port: Charge smartphones,

tablets and other USB-charged Devices.

Modular Jack

Connects to SmartCord for

powering your device

Earphone Jack

Connects to optional 3.5 mm stereo earphone.

Modular Connector

Plugs into detector jack

SmartCord USB Adapter

Connects to lighter/accessory socket

Mounting Bracket

Installation Controls & Features

Continued ➜

Display (OSP)

OverSpeed alert setting that can be

adjusted in Preferences. B lue tooth icon

will appear on display screen blue when

paired to phone and Speed limit data

will show here when ESCORT Live App

is open.

MRK

To mark a location for future alerts,

press MRK twice, then VOL + or – to

select the type of marker, then MRK

again to conrm. Press twice while

receiving marker alert to unmark

Display

Showing current speed

Power

Press to turn GT-360

on or o

MUTE

Press to mute an alert;

press three times to lock

out a false alert; press

twice while receiving a

locked-out alert to

unlock

BRT

Press to adjust display

brightness (Min, Med,

Max, Auto, Dark)

SEN

Press to adjust

detector sensitivity

(Auto, AutoNoX,

AutoLoK, and

Highway)

Volume

Press and hold + or – to

adjust volume

Mount Area

The EZ Mag Mount™

attaches to device here

Display

Alert area

OverSpeed Alert

Bluetooth

Speed Limit Data

OverSpeed Alert

Bluetooth

Speed Limit Data

Beltronics Beltronics GT-360 Owner's manual

Brand: Beltronics

Model: Beltronics GT-360

Category: Radar detectors

Type: Owner's manual

This manual is also suitable for

GT-360

Download PDF

report

Beltronics Beltronics GT-360 Owner's manual

This manual is also suitable for

Beltronics Beltronics GT-360 Owner's manual

Related papers

Other documents