For Technical Support:
For Technical Support:For Technical Support:
For Technical Support:
Call our Technical Service Department
Monday through Friday, 9 a.m. to 5 p.m. (EST)
1-800-832-8697
customer_support@enablingdevices.com
Pull and Play Switch #8042
USER’S GUIDE
50 Broadway
Hawthorne, NY 10532
Tel. 914.747.3070 / Fax 914.747.3480
Toll Free 800.832.8697
www.enablingdevices.com
Two Interchangeable grips!
Mount this switch to tabletop, wheelchair tray or bedrail for easy
access. It encourages reaching, swiping and grasping skills. It comes
with 2 interchangeable grips: 4 inch ball with holes and 3 inch T grip. C-
Clamp included. Size: 21"H x 7"W. Weight: 1¾ lbs.
Operation:
Operation:Operation:
Operation:
1. The Pull and Play Switch does
not
notnot
not
require any batteries to operate.
The switch is table top or wheelchair mountable with the included
C-Clamp. When mounting the switch take care not to over tighten
the C-Clamp, as this can cause damage to the surface you are
mounting to and also the Switch base.
2. Plug the Pull and Play Switch into the jack on your switch-adapted
toy/device. If it is necessary for you to use an adapter, make sure
that you use a MONO adapter, not a STEREO adapter.
3. Make sure that the connection between the Pull and Play Switch
and your toy/device is tight. There should be no gaps.
4. Chose one of the three included interchangeable grips. Once a grip
has been chosen, connect it to the chain via the spring loaded clip.
5. Simply pull on the switch’s grip, to activate your toy/device.
6. The toy/device will only remain activated while the Pull and Play
Switch continues to be actuated. Once you release the switch, the
toy/device will turn off.
Troubleshooting:
Troubleshooting:Troubleshooting:
Troubleshooting:
Problem:
Problem:Problem:
Problem:
The Pull and Play Switch does not activate your toy/device.
Action #1:
Action #1: Action #1:
Action #1: Make sure that the Pull and Play is on a flat surface (not
tilted or horizontal). This provides for optimal functioning.
Action #2:
Action #2: Action #2:
Action #2: Make sure that the connection between the Pull and Play
Switch and your toy/device is tight. There should be
no
no no
no
gaps. This is a
common error and an easy fix.
Action #3:
Action #3: Action #3:
Action #3: Try a different switch with your toy/device to rule out the
toy/device as the source of the problem.
Action #4:
Action #4: Action #4:
Action #4: Try a different adapter (if applicable) to rule this out as the
source of the problem.
Care of U
Care of UCare of U
Care of Unit:
nit:nit:
nit:
The Pull and Play Switch can be wiped clean with any household multi-
purpose cleaner and disinfectant.
Do not submerge
Do not submergeDo not submerge
Do not submerge the unit, as it will damage the contents and the
electrical components.
Do not use abrasive cleaners,
Do not use abrasive cleaners,Do not use abrasive cleaners,
Do not use abrasive cleaners, as they will scratch the surface of the
unit.
Rev
RevRev
Rev
6
66
6/2
/2/2
/2/17
/17/17
/17
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Enabling Devices 1671W User guide
-
Enabling Devices 806 - On Sale until 6/30/22 User manual
-
Enabling Devices 1070W User guide
-
Enabling Devices 1015 User manual
-
Enabling Devices 1032 User manual
-
Enabling Devices 8209 User manual
-
Enabling Devices 700 User manual
-
Enabling Devices 705 User manual
-
Enabling Devices 300 User manual
-
Enabling Devices 974 User manual
