Draw-Tite 36296 Installation guide

Type
Installation guide

Draw-Tite 36296 is a trailer hitch that can be installed on various Chrysler, Dodge, and Plymouth vehicles. It has a maximum gross trailer weight capacity of 3500 LB (1589 Kg) and a maximum tongue weight capacity of 300 LB (136 Kg). The hitch is designed to be used in the RISE position only and must be installed according to the instructions provided in the manual. The installation process involves removing the front and rear bumper bolts, installing the M12 X 1.75 studs into the frame, and then attaching the hitch to the studs.

Draw-Tite 36296 is a trailer hitch that can be installed on various Chrysler, Dodge, and Plymouth vehicles. It has a maximum gross trailer weight capacity of 3500 LB (1589 Kg) and a maximum tongue weight capacity of 300 LB (136 Kg). The hitch is designed to be used in the RISE position only and must be installed according to the instructions provided in the manual. The installation process involves removing the front and rear bumper bolts, installing the M12 X 1.75 studs into the frame, and then attaching the hitch to the studs.

Installation Instructions
Part Numbers:
06369
36296
90165
Hitch Shown In Proper Position
Wiring Access Location: SUV1, SUV2
Equipment Required:
Wrenches: 18mm, 19mm
Drill Bits: None
1. Remove only the front bumper bolts, both sides.
2. Install the M12 X 1.75 stud into position, until seated to frame, where bumper bolt was removed, both sides. Final tightening will
occur when nuts are tightened.
3. Remove rear bumper bolts and place hitch into position as shown.
4. Install remaining fasteners.
Rev. D3-7-07N36296Sheet 1 of 3
z 2001, 2004, 2007 Cequent Towing Products
Hex Nut – M12 x 1.75Qty. (2)
4
Spacer – 3/16 x 1-1/2 x 2Qty. (2)
2
Lock Washer – ½”Qty. (2)
3
Stud – M12 x 1.75 Qty. (2)
1
Tighten all M12 x 1.75 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
3500 LB (1589 Kg.) Max Gross Trailer Weight
300 LB (136 Kg.) Max Tongue Weight
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Drawbar must be used in the
RISE
position only.
Drawbar Kit:
36071
Fastener Kit: F36296
Form F206 Rev A 5605
Plastic
Fascia
Chrysler Town & Country
Chrysler Voyager
Dodge Caravan
Plymouth Voyager
(Fits all models 2WD, 4WD,
Short & Long Wheel Base)
Existing M12
Fastener
Bumper
Bracket
Bumper
Bracket
Frame rail
Frame rail
M12 X 1.75 Stud 1
Shown in Position
M12 X 1.75 Stud 1
Install this end
Into vehicle frame
Hitch attachment
To this end
1
2
3
4
1
2
3
4
39602
  • Page 1 1
  • Page 2 2
  • Page 3 3

Draw-Tite 36296 Installation guide

Type
Installation guide

Draw-Tite 36296 is a trailer hitch that can be installed on various Chrysler, Dodge, and Plymouth vehicles. It has a maximum gross trailer weight capacity of 3500 LB (1589 Kg) and a maximum tongue weight capacity of 300 LB (136 Kg). The hitch is designed to be used in the RISE position only and must be installed according to the instructions provided in the manual. The installation process involves removing the front and rear bumper bolts, installing the M12 X 1.75 studs into the frame, and then attaching the hitch to the studs.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI