STIEBEL ELTRON IA remote control Operation Instruction

BEDIENUNG UND INSTALLATION

OPERATION AND INSTALLATION

UTILISATION ET INSTALLATION

BEDIENING EN INSTALLATIE

OBSLUHA A INSTALACE

Multifernbedienung für Infrarot-Kurzwellen-Heizstrahler | Multi remote control for

short-wave infrared radiant heaters | Télécommande multifonctions pour radiateurs

radiants à ondes courtes IR | Multiafstandsbediening voor korte golf infrarood

straalkachel | Multifunkční dálkový ovladač pro infračervené krátkovlnné zářiče

» IA remote control

Page is loading ...

- 20 -

Page

Device explanation ..........................................................3

Safety instructions/Exclusion of liability .......................4

General safety instructions ............................................5

Scope of supply/general information ............................. 6

Intended use ....................................................................6

Instructions for radio operation .....................................7

Mounting of the wall bracket ..........................................8

Explanation of functions ................................................. 9

Transmission control light, Select button ....................9

Bidirectional / Unidirectional radio system .................10

Status display ............................................................10

Programming the transmitter .......................................10

Programming the transmitter/channel ........................12

Programming additional transmitters/channels ........... 13

Switching the radiant heater on/off ..............................14

Switching on the radiant heater..................................14

Switching on intermediate stages ...............................15

Deleting the transmitter ................................................16

Deleting individual channels / the complete transmitter .16

Technical data ...............................................................17

Changing the battery ....................................................17

Cleaning .........................................................................17

Disposal .........................................................................17

Overview of programming commands .........................18

Notes on repair .............................................................. 19

Notes on troubleshooting .............................................19

Contents

- 21 -

Device explanation

EN

Channel display

Operating mode display

UP button

STOP button

Status display

DOWN button

Select button

Programming button P

(under the cover)

Front of the device

Back of the device

- 22 -

Safety instructions / Exclusion of liability

Exclusion of liability:

It is essential to observe these operating instructions if the radiant

heater is to be used safely and if the various product characteristics

and performance features are to be achieved.

Stiebel Eltron GmbH & Co. KG assumes no liability for personal

injuries, property damages and financial losses that arise from non-

observance of the operating instructions.

Liability for material defects is excluded in such cases.

STOP!

Observance of the operating instructions is the pre-

requisite for disturbance-free operation and entitle-

ment for claims related to defects.

• Therefore, read the operating instructions before

you use the device!

• Ensure that the operating instructions are available

to the user in legible form.

• The operator must ensure that the basic safety

measures are observed and fulfilled.

• The operator must have completely read and

understood the operating instructions.

CAUTION!

The short-wave infrared radiant heater can only be

switched off completely by unplugging the mains plug

on the radiant heater.

- 23 -

General safety instructions

CAUTION!

Observe the following safety instructions.

Failure to observe them can lead to

physical injuries!

General

• Never install or commission devices which are dam-

aged.

• Only use unmodified original parts.

• If the device is opened without permission or used in an

improper manner, or if it is incorrectly installed or oper

-

ated, there is a risk of damage to persons and property.

• The device contains small parts which can be swal

-

lowed.

Installation

• All installation work must be carried out by an electri-

cian.

• This electrician must possess the appropriate qualifica

-

tion.

• Observe any country-specific conditions when install

-

ing the device.

• The device may only be used by persons who have

read and understood the operating instructions.

Operation

• Use only in dry rooms.

• If one or more transmitters are used for controlling the

system, then the system must be visible during opera

-

tion.

• Keep children away from the control units.

• Always replace batteries with an identical type (LR 06;

AA).

• Dispose of used batteries properly (collection point).

- 24 -

Scope of supply / General information / Intended use

Scope of supply

IA remote control (batteries contained in the device)

Wall bracket

2 wall plugs (Ø 6 mm)

2 screws (4 x 35)

Operating instructions

General information

The IA remote control has 5 channels, into which a number of

receivers can be programmed.

This device is characterised by simple operation, large control but-

tons and a Select button for channel selection.

The IA remote control is suitable for the operation of radiant heat-

ers that are equipped with an IA receiver.

Intended use

The IA rmeote control is a hand-held radio transmitter. This may be

used exclusively for the control of radiant heaters that are equipped

with an IA receiver.

Other use, or use beyond this is not considered to be use for

intended purpose.

Stiebel Eltron GmbH & Co. KG is not liable for:

• Other use than described above

• Changes to the device

• Improper use

Please see the technical data contained in these operating

instructions.

- 25 -

Instructions for radio operation

CAUTION!

Please observe the following safety instruc-

tions on radio operation.

Only use radio systems if they are allowed

and can be operated without interference.

• Please note that radio systems must not be operated

in areas with an increased risk of interference

(e. g. hospitals, airports, ....).

• The remote control is only approved for devices and

systems for which any malfunction of the transmitter

or receiver would not result in a risk for persons, ani

-

mals or property, or if such a risk is covered by other

safety equipment.

• The operator has no protection whatsoever from

interferences by other radio emitters and local ter

-

minals (e. g. also from radio installations, that are

normally used on the same frequency range).

• The range of the radio signal is limited by the govern

-

ment and the built environment.

NOTE!

The short-wave infrared radiant heater is operated by

the IA remote control via the IA receiver.

The short-wave infrared radiant heater can only be

switched off completely by unplugging the mains plug

on the radiant heater.

- 26 -

Mounting of the wall bracket

1. Fix the wall bracket so that the drill holes do not touch any

electrical lines!

2. Before mounting in the desired installation position, check that

transmitter and receiver are functioning properly.

3. Fix the bracket to the wall with the enclosed pins and screws.

The upper section of the wall bracket is moveable.

NOTE!

Before installation in the required assembly position,

check that the transmitter and receiver are functioning

properly.

The bracket has to be fixed so that the drill hole does

not touch any electrical lines.

- 27 -

Explanation of functions

Transmission control light

A radio signal is displayed by the lighting up of the transmission

control light.

The transmission control lamp flashes when transmitting if the bat-

tery power is reduced.

The transmitting power or the radio range will be reduced through

the reduction in the performance of the battery. If the transmission

control light no longer lights up when a button is pressed, the bat-

tery has to be replaced.

Select button

You can select up to 5 channels with the Select button. The indi-

vidual channels are indicated through illumination of the relevant

LED on the status display.

- 28 -

Explanation of functions

Bidirectional radio system

A bidirectional radio system means the transmission of radio signals

to radio receivers and optional feedback from the radio receivers

to the transmitter. The radio signal can be sent directly to the target

receiver. If this is not possible, the radio signal is relayed via other

bidirectional nodes until it reaches the target receiver. The target

receiver executes the command and sends a conrmation back to the

transmitter. Bidirectional radio operation is only possible if all nodes

are bidirectional. Otherwise the system is only unidirectional.

Unidirectional radio system

A unidirectional radio system means the transmission of radio signals

to radio receivers. However, in contrast to the bidirectional radio

system, the radio receivers cannot send any conrmation back to the

transmitter. The transmission of radio signals from one radio receiver

to another is also not possible.

Note

Do not press the P button before the receivers are ready for

programming. During programming the channel selects a radio

system. If the receivers are not ready for programming, the

transmitter channel changes to unidirectional mode. In order

to return to the initial status, press the STOP and P buttons

simultaneously for 6 seconds, until the status display illuminates.

Status display

A radio signal is indicated by illumination of the status display - in

different colours, according to the radio principle.

The transmitting power or the radio range will be reduced through

the reduction in the performance of the battery. If the status display

no longer illuminates when the button is pressed, the batteries

must be replaced.

Explanation of functions: Radio system

- 29 -

Status display

The different colours of the status display have the following

meanings:

Status display Meaning

Flashing orange Channel (transmitter) not programmed in any

receiver

Orange

Quick ashing

Channel (transmitter) in bidirectional program

-

ming mode. Operation of previously programmed

receivers not possible.

In group programming mode every 3 seconds

(even if button is not pressed)

Orange then green Channel (transmitter) operates bidirectionally

and receiver has received the signal

Orange then

ashing red

Channel (transmitter) operates bidirectionally

and one of the receivers has not received the

signal

Red then green Channel (transmitter) operates bidirectionally

and receiver has received the signal, batteries

weak

Red then ashing red Channel (transmitter) operates bidirectionally

and one of the receivers has not received the

signal, batteries weak

Green with repetition,

then red (unidirec

-

tional)

Channel (transmitter) has been deleted

Green Channel (transmitter) is operating unidrectionally:

Transmiiter signal is being sent

Alternating orange

and green (or red),

then red

Channel (transmitter) is deleted

Flashing red Batteries weak

- 30 -

Programming the transmitter/channel

PREREQUISITE!

The IA receiver must be installed.

!

1. Disconnect the fuse – and reconnect after a few seconds.

The receiver is now in programming mode for approx. 5 minutes.

2. Stand in front of the radiant heater with the IR remote control.

The radiant heater switch-

es between 100 % and

50 % of its heating power

for 2 minutes.

The transmitter is now programmed.

5. Press the ▲ button

within the first 2 sec.

of the programming

phase during the 100

% heating cycle.

6. Press the ▼ button

within the first 2 sec.

of the programming

phase during the 50 %

heating cycle.

Heating switches off for

a short time.

Heating switches off.

3. Press the Select

button to select a

channel.

4. Briefly press the

Programming button

P (on the back) .

- 31 -

Programming additional transmitters / channels

The transmitter is now programmed.

Programming additional transmitters / channels

To program additional transmitters in one receiver, please pro-

ceed as follows:

Press the buttons

for approx. 3 sec

-

onds. The heating

system alternates

between 100% and

50% heating power

for 2 minutes.

Press the ▲ button within the

first 2 sec. of the program

-

ming phase during the 100 %

heating cycle.

(New transmitter/channel)

Press the following buttons

on the programmed trans

-

mitter simultaneously:

▲ button

▼ button

Programming button P (on

the back).

Press the ▼ button within the

first 2 sec. of the programming

phase during the 50 % heating

cycle.

(New transmitter/channel)

Heating switches

off for a short time.

Heating

switches off.

NOTE!

If several receivers are connected to the same feed

line, then all are simultaneously ready to program.

Max. 16 transmitters can be programmed into a

receiver (IA receiver). The radiant heater begins to

briefly light up ‘at random’.

Individual channels/transmitters can now be assigned

to the respective receiver.

You can stop the flashing if you briefly push the STOP

button of a transmitter which has already been pro-

grammed.

The channel assignment/change can now be made with-

out you having to disconnect the individual receivers.

1.

3.

2.

- 32 -

Switching the radiant heater on/off

NOTE!

The IA receiver automatically switches the connected

radiant heater(s) off after 12 hours.

Switching the radiant heater on/off

PREREQUISITE!

The transmitter is now programmed.

!

Switching the heating system on.

Press the ▲ or ▼ button.

Switching the heating system off.

Press the STOP button.

NOTE!

The short-wave infrared radiant heater can only be

switched off completely by unplugging the mains plug

on the radiant heater.

- 33 -

Switching on intermediate stages

PREREQUISITE!

The transmitter is now programmed.

!

1. Briefly press the ▲ button twice in succession.

The radiant heater heats with approx. 66

% of its rated power.

2. Briefly press the ▼ button twice in succession.

The radiant heater heats with approx. 50

% of its rated power.

Switching on intermediate stages

- 34 -

Deleting transmitter/channels / Technical data

Deleting individual channels

Operating voltage 3 V DC

Battery type 2 x LR 06 (AA)

IP Code IP 20

Permitted ambient temperature 10 to +55 °C

Radio frequency 868.3 MHz

Notification number CE 0682

Dimensions in mm (remote control) L 120 x W 51 x H 26

Dimensions in mm (wall bracket) L 70 x W 26 x H 26

1. Press simultaneously:

• Programming button P (on the back)

• STOP button

2. Hold down this button combination for approx. 6 seconds,

until the LED goes out briefly 3x.

Deleting the complete transmitter

1. Press simultaneously:

• Programming button P (on the back)

• ▲ button

• STOP button

• ▼ button

2. Hold down this button combination for approx. 6 seconds,

until the LED goes out briefly 3x.

Technical data

- 35 -

Changing the battery / Cleaning / Disposal

Changing the battery

1. Unscrew the device at the bottom and open the

housing.

2. Remove the batteries.

3. Insert the new batteries (LR 06; AA) in the

correct position in the transmitter.

4. Reassemble the device.

Cleaning

Clean the device with a damp cloth only.

Do not use cleaning agents, these can attack the plastic.

Disposal

Please observe the current national regulations.

Dispose of according to the condition and existing regulations.

E.g. as:

• Electronic waste (PCB)

• Plastic (housing parts)

• Batteries

NOTE!

• Always replace batteries with an identical type

(2 x LR 06; AA).

• Dispose of used batteries properly (collection point).

- 36 -

Overview of programming commands

Function Key combination Procedure Condition/

Prerequisite

Starting programming

mode

(programming time: 2

min.)

Stopping programming

mode

●P

▲ + ▼ + ●P

●

Tap

Press for approx. 3 sec. until LED

goes out briey

Tap

Prior interruption of the mains

voltage (time frame 5 min.)

Transmitter is already pro-

grammed

Transmitter is already pro-

grammed

Programming the

transmitter

(IA remote control)

▲ at 100 %

heating power

▼ at 50 %

heating power

Briey press the 'UP' button im-

mediately (within 2 sec.) after the

radiant heater lights up with 100 %

heating power and briey press

the 'DOWN' button after the radiant

heater lights up with 50 % heating

power.

Acknowledgement takes place by

switching the radiant heater off.

The IA receiver is in program-

ming mode and the radiant

heater switches repeatedly to

100 % and 50 % of its heating

power

Deleting individual

channels

Deleting the complete

transmitter

●P + ●

▲ + ● + ▼ + ●P

Press for approx. 6 sec., until the

LED goes off briey

Press for approx. 6 sec., until the

LED goes off briey 3x and then

completely

Transmitter is already pro-

grammed

Transmitter is already pro-

grammed

- 37 -

Notes on repair / Notes on troubleshooting

Notes on repair

Please contact us if you are unable to eliminate a problem.

When contacting our service team, please always state the item

description and number from the type plate (back of device).

– Article number – Attendant circumstances

– Article designation – Own assumption

– Type of fault – Previously occurring unusual

events

Notes on troubleshooting

Fault Cause Remedy

No radio recep-

tion.

Transmitter is not

programmed.

Program the trans-

mitter.

Heater does

not heat or

only heats with

reduced power.

1. Radiant heater

wrongly connected.

2. Heating element is

defective.

3. Overtemperature

warning, overtem-

perature cutout

or emergency cut-

out active on the

receiver side.

1. Check

connection

(→ Radiant Heater

Instructions).

2. Replace heating

element

(→ Radiant Heater

Instructions).

3. Ensure cooling, in

case of emergency

shutdown also

switch off the sup-

ply voltage.

Page is loading ...

18 122.5301



Deutschland

STIEBEL ELTRON GmbH & Co. KG

Dr.-Stiebel-Straße 33 | 37603 Holzminden

Tel. 05531 702-0 | Fax 05531 702-480

[email protected]

www.stiebel-eltron.de

Verkauf Tel. 05531 702-110 | Fax 05531 702-95108 | info-center@stiebel-eltron.de

Kundendienst Tel. 05531 702-111 | Fax 05531 702-95890 | kund[email protected]

Ersatzteilverkauf Tel. 05531 702-120 | Fax 05531 702-95335 | ersat[email protected]

Irrtum und technische Änderungen vorbehalten! | Subject to errors and technical changes! | Sous réserve

d‘erreurs et de modifications techniques! | Onder voorbehoud van ver

g

issin

g

en en technische wi

j

zi

g

in

g

en! |

Salvo error o modificación técnica! | Excepto erro ou alteração técnica | Zastrzeżone zmian

y

techniczne i

ewentualne błędy | Omyly a technické změny jsou vyhrazeny! | A muszaki változtatások és tévedések

j

o

g

át

fenntartjuk! |

Отсутствие ошибок не гарантируется. Возможны технические изменения.

| Ch

y

b

y

a

technické zmeny sú vyhradené! Stand 9046

Australia

STIEBEL ELTRON Australia Pty. Ltd.

6 Prohasky Street | Port Melbourne VIC 3207

Tel. 03 9645-1833 | Fax 03 9645-4366

[email protected]

www.stiebel.com.au

Austria

STIEBEL ELTRON Ges.m.b.H.

Eferdinger Str. 73 | 4600 Wels

Tel. 07242 47367-0 | Fax 07242 47367-42

[email protected]

www.stiebel-eltron.at

Belgium

STIEBEL ELTRON bvba/sprl

't Hofveld 6 - D1 | 1702 Groot-Bijgaarden

Tel. 02 42322-22 | Fax 02 42322-12

[email protected]

www.stiebel-eltron.be

China

STIEBEL ELTRON (Guangzhou) Electric

Appliance Co., Ltd.

Rm 102, F1, Yingbin-Yihao Mansion, No. 1

Yingbin Road

Panyu District | 511431 Guangzhou

Tel. 020 39162209 | Fax 020 39162203

[email protected]

www.stiebeleltron.cn

Czech Republic

STIEBEL ELTRON spol. s r.o.

K Hájům 946 | 155 00 Praha 5 - Stodůlky

Tel. 251116-111 | Fax 235512-122

[email protected]

www.stiebel-eltron.cz

Finland

STIEBEL ELTRON OY

Kapinakuja 1 | 04600 Mäntsälä

Tel. 020 720-9988

[email protected]

www.stiebel-eltron.fi

France

STIEBEL ELTRON SAS

7-9, rue des Selliers

B.P 85107 | 57073 Metz-Cédex 3

Tel. 0387 7438-88 | Fax 0387 7468-26

[email protected]

www.stiebel-eltron.fr

Hungary

STIEBEL ELTRON Kft.

Gyár u. 2 | 2040 Budaörs

Tel. 01 250-6055 | Fax 01 368-8097

[email protected]

www.stiebel-eltron.hu

Japan

NIHON STIEBEL Co. Ltd.

Kowa Kawasaki Nishiguchi Building 8F

66-2 Horikawa-Cho

Saiwai-Ku | 212-0013 Kawasaki

Tel. 044 540-3200 | Fax 044 540-3210

[email protected]

www.nihonstiebel.co.jp

Netherlands

STIEBEL ELTRON Nederland B.V.

Daviottenweg 36 | 5222 BH 's-Hertogenbosch

Tel. 073 623-0000 | Fax 073 623-1141

[email protected]

www.stiebel-eltron.nl

Poland

STIEBEL ELTRON Polska Sp. z O.O.

ul. Działkowa 2 | 02-234 Warszawa

Tel. 022 60920-30 | Fax 022 60920-29

[email protected]

www.stiebel-eltron.pl

Russia

STIEBEL ELTRON LLC RUSSIA

Urzhumskaya street 4,

building 2 | 129343 Moscow

Tel. 0495 7753889 | Fax 0495 7753887

[email protected]

www.stiebel-eltron.ru

Slovakia

TATRAMAT - ohrievače vody s.r.o.

Hlavná 1 | 058 01 Poprad

Tel. 052 7127-125 | Fax 052 7127-148

[email protected]

www.stiebel-eltron.sk

Switzerland

STIEBEL ELTRON AG

Industrie West

Gass 8 | 5242 Lupfig

Tel. 056 4640-500 | Fax 056 4640-501

[email protected]

www.stiebel-eltron.ch

Thailand

STIEBEL ELTRON Asia Ltd.

469 Moo 2 Tambol Klong-Jik

Amphur Bangpa-In | 13160 Ayutthaya

Tel. 035 220088 | Fax 035 221188

[email protected]

www.stiebeleltronasia.com

United Kingdom and Ireland

STIEBEL ELTRON UK Ltd.

Unit 12 Stadium Court

Stadium Road | CH62 3RP Bromborough

Tel. 0151 346-2300 | Fax 0151 334-2913

[email protected]

www.stiebel-eltron.co.uk

United States of America

STIEBEL ELTRON, Inc.

17 West Street | 01088 West Hatfield MA

Tel. 0413 247-3380 | Fax 0413 247-3369

[email protected]

www.stiebel-eltron-usa.com

A 319416-38849-9053

C 18 122.5301

4<AMHCMO=bjebgd>

STIEBEL ELTRON IA remote control Operation Instruction

STIEBEL ELTRON IA remote control Operation Instruction

in other languages

Related papers

Other documents