Generac Portable Products 2300PSI 1674-0 Owner's manual

Brand: Generac Portable Products

Model: 2300PSI 1674-0

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

anuaJ

Questions? Help is just a moment away!

Call: Generac Pressure Washer Heipiine = 1=800=270=1408 M=F 8=5 CT

VVeb:wwwogenerac-portabiesocorn or www.briggsandstratton.com

Model No. 1674o0 (2_300 PSI Pressure Washer) Manual No. 190134G8 Revision 4 (08/14/2002)

Y_&_ $_ra_on'

_ powE__opucT_

TABLE OF CONTENTS

Safety Rules .................................. 2°3

Know Your Pressure _A/asher ...................... 4

AssembHy .................................... S-7

Operation .................................. 8-HH

Product Specifications ........................... HH

Maintenance ............................... H2-H 4

Storage ...................................... H4

TroubHeshooting ............................... HS

RepHacement Parts ........................... H6- H9

_A/ar ranty ............................... Last Page

EQUmPNENT

Read this manuam carefummy and become famimiar

with your pressure washer. Know its appmications, its

mimitations and any hazards invomved.

Every effort has been made to ensure that information in

this manuaH is accurate and current. However, Generac

reserves the right to change, alter or otherwise improve the

product and this document at any time without prior notice.

WARNING

WNEN ADDING FUEL

Turn pressure washer OFF and let it cool at least 2 minutes

before removing gas cap.

Fill fuel tank outdoors.

Do not overfill tank.Allow space for fuel expansion.

Keep gasoline away from sparks, open flames, pilot lights, heat,

and other ignition sources.

Do not light a cigarette or smoke.

VNEN OPERATING EQUIPMENT

FUEL iN TANK

Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite gasoline vapors.

SAFETY RULES

The safety aHert symbol (_) is used with a signaH word

(DANGER, CAUTION,WARNING), a pictorial and/or a

safety message to aHert you to hazards. DANGER indicates

a hazard which, if not avoided, wil/resuHt in death or serious

iniury. WARNING indicates a hazard which, if not

avoided, could resuHt in death or serious iniury. CAUTION

indicates a hazard which, if not avoided, might resuHt in

minor or moderate iniury. CAUTION, when used

without the aHert symbol indicates a situation that couHd

resuHt in equipment damage. Follow safety messages to

avoid or reduce the risk of iniury or death.

WARNING

Keep water spray away from electric wiring or fatal electric

shock may result.

WARNING

Never aim the spray gun at people, animals or plants.

Do not allow CHHLDREN to operate the pressure washer:

Never repair high pressure hose. Replace it.

bye& S_on _

_ POV/ERp_D_JCrS

WARNING

Keep spray nozzle between 8 to 24 inches away from cleaning

surface.

Be extremely careful if you must use the pressure washer from

a ladder, scaffolding or any other relatively unstable location.

The cleaning area should have adequate slopes and drainage to

reduce the possibility of a fail due to slippery surfaces.

Operate this unit on a stable surface.

WARNING

Do not wear loose clothing, iewe]ry or anything that may be

caught in the starter or other rotating parts_

Tie up long hair and remove iewelr_;

WARNING

Always wear eye protection when you use this equipment or

when you are in the vicinity where the equipment is in use.

DANGER

Operate pressure washer ONLY outdoors.

Use a respirator or mask whenever there is a chance that

vapors may be inhaled.

Read all instructions with mask so you are certain the mask will

provide the necessary protection against inhaling harmful vapors.

i WARNING

WARNING

Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

CAUTION

Do not tamper with governed speed.

Do not operate the pressure washer above the rated pressure.

, Do not touch hot surfaces.

, Allow equipment to cool before touching.

Do not point spray gun at glass when in the iet spray mode.

Never aim the spray gun at plants.

Y_&_ $_ra_on'

_ powE_P_ODUCTS

KNOWYOUR PRESSURE WASHER

Read this owner's manuaJ and safety rules before operating your pressure washer,

Compare the ilhstradons with your pressure washer to familiarize yourself with the locaqons of various controls and

adjustments. Save this manual for future reference.

High Pressure Hose

Recoil Starter

Throttle Contr

AccessoryTray

SprayGun

Chemical Injection

Air

Oil Fill/Dipstick

VVater Inlet

Choke Lever

Adjustable Nozzle

High Pressure Outlet

Pump equipped with Automatic

Cool Down System

AccessoryTray -- Provides convienant storage for

standard and optional accessories, such as brushes, turbo

wands, ect.

Adjustable Nozzle --Always attached to nozzle

extension.Adjustable nozzle allows you to adjust spray

pressure and spray pattern.

Air Filter -- Dry type filter element limits the amount of

dirt and dust that gets in the engine.

Automatic Cool Down System -- Cycles water

through pump when water reaches 125°° 155°PA/arm

water will discharge from pump onto ground.This system

prevents internal pump damage.

Chemical injection Siphon/Filter -- Use to siphon

detergent or other pressure washer chemicals into the low

pressure stream.

Choke Lever -- Prepares a cold engine for starting.

High Pressure Hose -- Connect one end to water

pump and the other end to spray gun.

High Pressure Outlet -- Connection for high pressure

hose.

Oil FiJJ/DipsticJ< -- Check and fill with oil here.

Pump -- Develops high pressure.

Recoil Starter -- Used for starting the engine manually.

Spray Gun -- Controls the application of water onto

cleaning surface with trigger device. Includes safety latch.

Throttle Control Lever -- Sets engine in starting mode

for recoil starter and stops a running engine.

Water inlet -- Connection for garden hose.

bye& S_on _

_ POWERp_r_UCrs

iMPORTANT: Read entire owner's manuaH before you

attempt to assembie or operate your new pressure washer.

REMOVE PRESSURE

WASHER FROM

o Remove the parts bag, accessories, and insert inciuded

with pressure washer.

o Siice two corners at the end of carton from top to

bottom so the panei can be foided down flaL then

remove ali packing material

o Roli pressure washer out of carton.

Carton Contents

Items in the carton include:

Hain Unit

Goggies

Handie

Piastic Accessory Tray

High Pressure Hose

Spray Gun

Nozzie Extension

Oil Bottle

Parts Bag (which inchdes the following):

Owner's Planual

Engine Planual

Owner's Registration Card

Plaintenance Kit

Handle Fastening Hardware Kit (which includes):

Carriage Bolts (2)

Plastic Knobs (2)

"J" Hook

Chemical Hose Clip

Self Tapping Screws (5)

ff any of the above parts are missing or damage& cail the

pressure washer heipiine at 1-800-270-[ 408.

PREPARING PRESSURE

WASHER FOR USE

If you have any problems with the assembly of your

pressure washer or if parts are missing or damage& cail the

pressure washer heipiine at [ -800-270- [ 408.

To prepare your pressure washer for operation, you

wi[[ need to perform these tasks:

o Fiil out and send in registration card.

o Attach accessory tray to handie_ then attach handle to

main unit.

o Add oi[ to engine crankcase.

o Add fuel to fuel tank.

o Connect high pressure hose to spray gun and pump.

o Connect water supply to pump.

Attach Handle and Accessory Tray

NOTE: AHHassembiy operations given in this section wiHHbe

described from the perspective of assembling the pressure

washer from the rear.

o Slide the plastic accessory tray onto the handle and align

the holes in the accessory tray with the holes on the

handle (Figure I).

o Secure tray to handle with self tapping screws using a

#2 phillips screwdriver. Ensure screws are tight but not

crushing the plastic accessory tray.

Y_&_ $_ra_on'

_ powE_e_ODUCT_

* Phce the hande onto the hande supports aHready

connected to the main unit. Make sure the holes in the

hande aHign with the holies on the hande supports

(Figure 2).

NOTE: It may be necessary to move the handHe supports

from side to side in order to aHign the hande so it will sHide

over the handHe supports.

° Insert the carriage boHt through the holies from the

outside of the unit and attach a phstic knob from the

inside of the unit.Tighten by hand (Figure 3).

, insert the "J" hook into the second from the left slot in

the accessory tray (Figure 4).

* Pinch the chemical hose that comes out of a hole in the

unit's base and slide it into the metal clip_ as shown in

Figure 5.

* Tilt the unit up by the handle and attach the metal clip to

the rib on the left underside of the accessory tray

(Figure 6). Slide the chemical hose through the metal clip

so that it is tight but not kinked.

Add Engine Oil

JNPORTANT: Any attempt to crank or start the engine

before it has been properly serviced with the

recommended oil may result in an engine failure.

* Place pressure washer on a [eve[ surface.

° Refer to the engine owners manual to add recommended

oil to engine.

NOTE: Check oil often during engine break-in. Refer to

engine owner's manual for recommendations.

Add Gasoline

WARNING! Never fill fuel tank indoors. Never

fi[[ fuel tank when engine is running or hot. Do Not

smoke when filling fuel tank.

WARNING! Never fill fuel tank completely full.

Provide space for fuel expansion.Wipe away any fuel

spillage from engine and equipment before starting.

bye& S_on _

_7_ POV/ER_r>UCrs

° Use fresh_ dean unHeaded automotive gasohne and store in

approved, dean, covered containers. Use dean fill funneHs.

Never use "staHe" gasoHine Heft over from Hast season or

gasoHine stored for Hong periods.

° CHean area around fueHfill cap, remove cap.

° SHowilyadd "UNLEADED" reguhr gasoHine to fueHtank.

Use a funneH to prevent spillage. SHowilyfill tank to about

H.5'_ bellow the bottom of the filler neck (Figure 7).

° Install fuel cap and wipe up any spilled gasoline.

Connect Hose and Water Supply to

mMPORTANT:You must attach all hoses before you start

the engine. Starting engine without all hoses connected and

water supplied will damage the pump.

° Attach one end of the high pressure hose to the high

pressure outlet on the pump (Figure 8).Tighten by hand.

, Attach the other end of the hose to the base of the

spray gun (Figure 9).Tighten by hand.

Connect High

Pressure Hose

Here

° Before you connect your garden hose to the water inlet,

inspect the inlet screen (Figure I 0). Clean the screen if it

contains debris, replace it if it is damaged. DO NOT RUN

THE PRESSUREWASHEP_ IFTHE SCREEN IS DAMAGED.

Inspect inlet

screen. Do Not

use if damaged;

clean if dirty.

° Run water through the garden hose for 30 seconds to

clean out any debris.Turn off water.

mMPORTANT: Do Not siphon standing water for the

water supply. Use ONLY cold water (less than 100°F).

° Connect the garden hose to the water inlet.Tighten by

hand (Figure 10).

CAUT|ON!There HUST be at least ten feet of

unrestricted garden hose between the pressure washer

inlet and any flow shut off device, such as a 'Y' shut-off

connector or other convenience-type water shut-off valve.

Damage to pressure washer resulting from disregarding this

caution will not be covered by the warranty.

° Turn ON the water and squeeze the trigger on the spray

gun to purge the pump system of air and impurities.

CAUTION! Before starting the pressure washer,

be sure you are wearing adequate eye protection.

Checklist Before Starting Engine

Review the unit's assembly to confirm you have performed

all of the following;

, Hake sure the handle is in place and secure.

, Check that oil has been added to the proper level in the

engine crankcase.

, Add the proper gasoline to fuel tank.

, Check for properly tightened hose connections.

, Check to make sure that there are no kinks, cuts, or

damage to the high pressure hose.

, Provide a proper water supply at an adequate flow.

, Be sure to read "Safety Rules" and "HowTo Use Your

Pressure Washer" before using the pressure washer.

Y_&_ $_ra_on'

_ powE__ODUCT_

NOWTO USEYOUR

PRESSURE WASHER

If you have any problems operating your pressure washer,

please call the pressure washer heIpline at

I=800=270=1408.

To Start You r Pressu re Washer

To start your pressure washer for the first time_follow these

instructions step=by=step.This starting information also applies if

you have let the pressure washer sit idle for at least a day.

. Place the pressure washer in an area close enough to an

outside water source capable of supplying water at a flow

rate greater than 2.2 gallons per minute.

. Check that the high pressure hose is tightly connected to

the spray gun and to the pump. See "Preparing Pressure

Washer For Use" for illustrations.

o Hake sure unit is in a level position.

° Connect the garden hose to the water inlet on the

pressure washer pump. Turn ON the water.

CAUTION! Do Not run the pump without the water

supply connected and turned on.You must follow this

caution or the pump will be damage&

° Squeeze trigger on gun until you have a steady stream of

water.This purges the pump of air and impurities.

. Attach nozzle extension to spray gun (Figure I I).Tighten

by hand.

o Position the nozzle in the low pressure mode (slide

nozzle forward) and squeeze the trigger on the spray gun

to relieve pressure caused by turning ON the water.

VVater will flow out of the gun in a thin stream. Continue

to hold trigger until there is a steady stream of water

and no air remains in the system. Release the trigger.

° Engage the safety latch to the spray gun triger

(Figure 12).

o Hove the throttle lever to "Fast" position, shown here

as a rabbit (Figure 13).

Throttl

Choke Lever

o Hove the choke lever to the "Choke" position

(Figure 13).

NOTE: For a warm engine, be sure the choke lever is in

the "P_un" position.

o Place your left foot on the lower frame and grasp the

handle as shown (Figure 14).Your unit may appear slightly

different from that shown here.

* Pull the starter grip handle lightly with your right hand

until you feel some resistance, then pull briskly.

bye& S_on _

_7 POWERp_JC rs

° Return the startergriphandHeshowily.Do Not Herrope

"snap bacH<" against starter.

, VVhen engine starts, showily move choke Heverto the

"Run" position.IfenginefaHters,move choke Heverto the

"Choke" position, then to the "Run" position.

° if engine faiHsto s_rt after six puHHs,move choke Heverto

the "Run" position. If engine fires, but does not continue

to run, move choke Hever to the "Choke" position, then

to the "Run" position.

NOTE: If the recoiHstarter is hard to puHLit may be necessary

to squeeze the gun triter to reHieveinternaH pump pressure.

How to StopYour Pressure Washer

. Hove throtde Hever on engine to "Stop" position.

. Squeeze trigger on the spray gun to relieve

pressure in the hose_

NOTE:A smaHHamount of water wiHHsquirt out when you

reHeasethe pressure.

How to Use Accessory "Tray

The unit is equipped with an accessory tray with pHacesto

store your nozzHeextension, and shotsto hoHd the cHeaning

soHution bottHe and the detergent siphoning fiHter.There are

aHsotwo hooks at the ends of the accessory tray to hoHd

your spray gun and high pressure hose.

NOTE:The extra holies in the tray are for storing a brush

and a turbo wand.The brush and turbo wand are NOT

incHuded with your pressure washer.You can buy these

items as optionaH accessories.

. PHacethe nozzHe extension through the hoHeon the

accessory tray, as shown in Figure H5.

/ i

Hang your chemicaH soHution bottHe on the "J" hook and

pHacethe detergent siphoning fiHter in the Hastshot on the

Heft(Figure HS).

° Hang the high pressure hose on the hook on the right

side of the accessory tray (Figure H5).

° PHacethe spray gun on the hook on the Heftside of the

accessory tray as shown on page 4.

How to Use the Adjustable Nozzle

You now shouHd know how to START your pressure

washer and how to STOP it.The information in this

section wiHHteHHyou how to adiust the spray pattern and

appHydetergent or other cHeaningchemicaHs.

CAUTION! Never adiust spray pattern when

spraying.Never put hands in front of nozzHeto

adiust spray pattern.

The adiustabHenozzHeaffixed to the nozzHeextension

permits you to adiust the spray pattern and the spray

pressure_asfoHHows:

Y_&_ $_ra_on'

_ powE_P_ODUCTS

° SHidethe nozzHe forward to adjust the spray to How

pressure mode (Figure H6).SHidethe nozzHe backward to

achieve high pressure.

SHidenozzHe backward

for high pressure mode.

SHidenozzHeforward for

How pressure mode and

detergent application.

° Point the nozzHe down towards a firm surface and press

the trigger to test the pattern (Figure H7).

° Twisting the nozzHe adjusts the spray pattern from a

narrow pattern to a fan pattern (Figure H8).

Twist nozzHe

countercHockwise for fan

spray pattern,

Twist nozzHe cHockwise

for narrow spray

pattern.

° For most effective cHeaning, keep the spray nozzHe

between 8 to 24 inches away from cHeaning surface.

. If you get the spray nozzHe too chose, especiaHHy using high

pressure mode,you may damage the surface being

cHeaned.

. Do Noe get cHoser than 8 inches when cHeaning tires.

Applying Detergent with the

Adjustable Nozzle

CAUTION! You must aeeach all hoses before you start

the engine. Starting the engine without all the hoses

connected and without the water turned ON wiHHdamage

the pump.

IMPORTANT: Use soaps designed speci_cammy for

pressure washers. HousehoHd detergents couHd damage

the pump.

To apply deeergene, follow ehese steps:

* Review the use of adjustabHe nozzHes.

* Prepare detergent soHution as required by the

manufacturer.

° Hang the detergent soHution on the "J" hook attached to

the accessory tray, as shown in Figure H9.

° PHace the smaHHfiHter end of the detergent siphoning tube

into the detergent container.

CAUTION! Keep the detergent siphoning tube from

coming in contact with the hot muffler.

. SHidethe adjustable nozzle forward to How pressure

mode. Detergent cannot be appHiedwith the nozzle in

high pressure position.

bye& S_on _

_ POWERp_UC rs

, Hake sure the garden hose is connected to the water

inHet.Check that the hgh pressure hose is connected to

the spray gun and the pump. Start the engine.

° AppHy the detergent to a dry surface, starting at lower

portion of area to be washed and work upward, using

Hong,even, overlapping strokes.

° AHHowthe detergent to "soak in" for 3-5 minutes before

washing and rinsing. ReappHyas needed to prevent

surface from drying. Do Not allow the detergent to dry

on (prevents streaHdng).

mMPORTANT:You must flush the chemicaH injection

system after each use by pHacingthe fiHter into a bucket of

dean water, then run the pressure washer in How pressure

for H=2minutes.

Pressure Washer Rinsing

WARNING! Be extremeHy carefuH if you must

use the pressure washer from a Hadder,scaffoHding

or any other relatively unstabHe Hocation. Pressure in

a running washer buiHdsas you cHimb.When you

press the trigger, the recoiH from the initiaH spray

couHd cause you to fall.The high pressure spray

couHd aHso cause you to fall if you are too chose to

the cHeaning surface.

For Rinsing:

, SHidethe nozzHe backward to high pressure and press the

trigger. It wiHHtake a few seconds for the detergent to

clear.

NOTE:You can aHsostop detergent from flowing by simpHy

removing detergent siphon tube from botde.

, Keep the spray gun a safe distance from the area you

pHanto spray.

" AppHy a high pressure spray to a smaHHarea, then check

the surface for damage. If no damage is found, it is okay

to continue rinsing.

° Start at the top of the area to be rinsed, working down

with same overHappingstrokes as you used for cHeaning.

Automatic Cool Down System

(Thermam Remief}

If you run the engine on your pressure washer for

3=5minutes without pressing the trigger on the spray gun,

circuHating water in the pump can reach a temperature

between H25°-H 55°EWhen the water reaches this

temperature, the automatic cool down system engages and

cooHs the pump by discharging the warm water onto

the ground. This system prevents internaH damage to the

pump.

SPECRFRCATRONS

Rated Pressure ..... 2,300 psi

Flow Rate .......... 2.0 gaHHonsper minute (gpm)

Detergent .......... Use detergent approved for

pressure washers

Water SupplyTemp . Not to exceed H00°F

Automatic Cool .... VViHHcycHewhen water

Down System ....... reaches H25 °° H55°F

Shipping Weight .... 77 Hbs.

Y_&_ S_ra_on'

_ powE__opucT_

GENERAL MAmNTENANCE

RECOMMENDATmONS

The pressure washer warranty does not cover items that have

been subjected to operator abuse or neghgence.To receive full

value from the warranty, the operator must maintain the

pressure washer as instructed in this manual

° Some adjustments wiHHneed to be made periodicaHHyto

properHy maintain your pressure washer. Check the spray

gun and adjustable nozzHeextension assembHyfor wear.

° AHHmaintenance in this manuaHand the engine owner's

manuaH shouHdbe made at Heastonce each season.

o Once a year you shouHddean or replace the spark pHug,

dean or replace the air fiker.A new spark pHugand dean

air fiHter assure proper fueHoairmixture and heHpyour

engine run better and Hastlonger. PHeaserefer to your

engine owner's manuaHfor more details.

BEFORE EACH USE

° Check engineoiHHeveL

° Check water inHetscreen for damage.

, Check in4ine finer for damage.

, Check high pressure hose for Heaks.

, Check detergent siphoning tube and finer for damage.

, Check spray gun and adjustabHe nozzHe extension

assembHyfor Heaks.

, Rinse out garden hose to flush out debris before

connecting to pressurewasher.

PRESSURE WASHER

MAmNTENANCE

Check and Clean Inlet Screen

Examine the screen on the water inHet.CHeanit if the

screen is dogged or repHace it if screen is damaged.

Check High Pressure Hose

The high pressure hose can deveHop Heaksfrom wear,

kinking, or abuse. Inspect the hose each time before using

it. Check for cuts, Heaks,abrasions or buHgingof cover.

damage or movement of coupHings. If any of these

conditions exist, repHacethe hose immediately.

CAUT|ON! Water spraying from a Heakis capabHe

of injecting materiaH into skin. Inspect hose each

time before using it. Never repair a high pressure

hose. RepHaceit with another hose that exceeds the

maximum pressure rating of your pressure washer.

Check Detergent Siphoning Tube

Examine the fiHter on the detergent tube and dean if

dogged.The tube shouHd fit tightHy on the barbed fitting.

Examine the tube for Heaksor tears. RepHacethe finer or

tube if either is damaged.

C[ean[n_ent S[phoninS:Tube

if you used the detergent siphoning robe,you must flush it

with dean water before stopping the engine.

° PHacethe chemicaH injection siphon/fiNer in a bucket fuHH

of dean water.

° SHidethe adiustabHe nozzHeextension forward to the How

pressure mode.

° Rush for Ho2 minutes.

° Shut off the engine.

IMPORTANT: SimpHyshutting OFF engine wiHHnot

reHeasepressure in the system, When the engine has

shut down, squeeze the trigger on the spray gun to

relieve the pressure in the hose,

Check Gun and Adjustable Nozzle

Examine the hose connection to the spray gun and make

sure it is secure,Test the trigger by pressing it and making

sure it "springs bacH<"into pHacewhen you reHeaseit, Put

the safety Hatchin the ON position and test the trigger, You

shouHdnot be abHeto press the trigger,

Check in-Line F[Ker

Referto Figure20 and servicethe inoHinefiHterifit

becomes dogged,asfoHHows:

NozzHe Extension

Oorir

bye& S_on _

_ _OV/ERp_r>_JCrs

H. Detach spray gun and nozzHe extension from hgh

pressure hose. Detach nozzHe extension from spray gun

and remove o:fing and screen from nozzHe extension.

Hush the screen_ spray gun_ and adiustabHe nozzHe

extension with dean water to dear debris.

2. If the screen is damaged_ the o:fing Halt contains a

repHacement inoHine fiker screen and an o:fing. [f

undamaged_ reuse screen.

3. PHace the inoHine fJker screen into the threaded end of

the nozzHe extension. Direction does not matter. Push

the screen in with the eraser end of a penciH untiH it

rests ilat at the bottom of the opening.Take care to

not bend the screen.

4. PHace the o°ring into the recess. Push the o°ring snugHy

against the inoHine fiker screen.

5. AssembHe the nozzHe extension to the spray gun, as

described earHier in this manual

Purge Pump of Air and

To remove air from the Dump, follow these steps:

Set up the pressure washer as described in "Preparing

Pressure VVasher For Use". Connect the water suppHy and

turn water on.

o PuHHthe trigger on the spray gun and hoHd.

o When the water suppHy is steady and constant_ engage

the safety Hatch.

To remove contaminants from the pump, follow

these stepst

o Set up the pressure washer as described in "Preparing

PressureWasher For Use". Connect the water suppHy

and turn water on.

o Start the engine according to instructionsin"To Start

Your Pressure VVasher".

° Remove nozzle extension from spray gun.

o Squeeze the trigger on the spray gun and hoHd.

o When the water suppHy is steady and constant, engage

the safety Hatch and attach the nozzHe extension.

Nozzle Maintenance

A puHsing sensation fek whiHe squeezing the spray gun

trigger may be caused by excessive pump pressure.The

principa[ cause of excessive pump pressure is a nozzHe

c[ogged or restricted with foreign materiak such as dirt,

etc.To correct the problem, immediately clean the nozzle

using the tooHs incHuded with your pressure washer and

foHHow these instructions:

I. Shut off the engine and turn off the water supply.

2. Detach the nozzHe extension from the spray gun.Twist

the nozzHe c[ockwise to the stream position. Using the

suppHied 2ram (5/64) aHHen wrench, remove the nozzHe

from the end of the nozzHe extension (Figure 21).

3. Remove the inoline filter from the other end of the

nozzHe extension.

4. Use the wire incHuded in the kit (or a smaHHpaper chip)

to free any foreign materia[ dogging or restricting the

nozzHe (Figure 2H).

5. Using a garden hose, remove additionaH debris by bacH<

flushing water through the nozzHe extension

(Figure 22). BacH<flush between 30 to 60 seconds.Turn

the adiustabHe nozzHe extension to stream spray and

move the nozzHe from How to high whiHe flushing.

6. Reinstall the nozzle and in4ine filter into the nozzle

extension. Do Not overtighten the nozzle with the

allen wrench.

7. Reconnect the nozzle extension to the spray gun.

8. Reconnect the water supply, turn on the water, and

start the engine.

Y_&_ $_ra_on'

_ powE_P_ODUCTS

9. Test the pressure washer by operating with nozzHe in

the high and in the Howpositions.

O-Rin 8 Maintenance

Through the normal operation of your pressure washen

o-rings, which keep the connections of the hoses and spray

gun tight and leak-free, may become worn or damaged.

Provided with your pressure washer is an O-Ring

Haintenance Kit which includes rephcement o-rings, rubber

washer and water inlet filter. Refer to the instruction sheet

provided in the kit to service your unit's o-rings. Note that

not all of the parts in the kit will be used on your unit.

To remove a worn or damaged o-ring:

Use a small flathead screwdriver to get underneath the

o-ring and pry it off.

ENGINE MAINTENANCE

See the engine owner's manual for instructions on how to

properly maintain the engine.

CAUTION! Avoid prolonged or repeated skin

contact with used motor oil. Used motor oil has

been shown to causeskin cancer in certain

laboratory animag.ThorougNy wash exposed areas

with soap and water.

KEEP OUT OF REACH OF CHILDREN. DON'T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OILTO COLLECTION CENTERS.

PREPARING THE UNIT

FOR ,STORAGE

Water should not remain in the unit for long periods of

time. Sediments or minerals can deposit on pump parts and

"freeze" pump action. If you do not plan to use the pressure

washer for more than 30 days, follow this procedure:

I. Flush detergent siphoning tube by placing the filter into

a pail of clean water while running pressure washer in

low pressure mode (adjustable nozzle in the forward

position). Flush for one to two minutes.

2. Shut off the engine and let it cool, then remove high

pressure and garden hoses. Disconnect spark plug wire

from spark plug.

3. Empty the pump of all pumped liquids by pulling the

recoil handle about 6 times.This should remove most

of the liquid in the pump.

4. Use Generac brand PumpSaver to prevent corrosion

build up and freezing of pump.

5. Store unit in a clean, dry area.

Protecting the Pum

To protect the pump from damage caused by mineral

deposits or freezing, use the Generac PumpSaver to treat

pump.This prevents freeze damage and lubricates pistons

and seals.

NOTE: Generac PumpSaver, model number 01559, is available

as an optional accessory. It is not included with the pressure

washer.

CAUTION!You must protect your unit from freezing

temperatures. Failure to do so will permanently damage

your pump and render your unit inoperable. Freeze damage

is not covered under warranty.

CAUTION! Read and follow all cautions and

warnings on the PumpSaver can hbd.AIways wear

eye protection when using PumpSaver.

To use PumpSaver, make sure the pressure washer is

turned off and disconnected from supply water. Read and

follow all instructions and warnings given on the PumpSaver

container.

NOTE: PumpSaver will drip from pump after treatment

and will stain wood and concrete.

NOTE: If PumpSaver is not avaihble, draw RV antifreeze

(non=alcohol) into the pump by pouring the solution into a

3-foot section of garden hose connected to inlet adapter

and pulling recoil handle twice.

STORING THE ENGINE

See the engine owner's manual for instructions on how to

properly prepare the engine for storage.

bye& S_on _

_7_ POWERp_C_UCrs

TROUBLESHOOTmNG

Problem

Pump has following

problems: failure to

produce pressure, erratic

pressure, chattering, loss

of pressure, low water

volume.

Detergent fails to mix

with spray.

Cause

I. Nozzle in low pressure mode.

2. Water inlet is blocked.

3. Inadequate water supply.

4. Inlet hose is kinked or leaking.

5. Clogged inlet hose strainer.

6. Water supply is over 100°F.

7. High pressure hose is blocked or

leal<s.

8. Gun leal<s.

9. Nozzle is obstructed.

10. Pump is fault7.

I. Detergent siphoning tube is not

submerged.

2. Chemical filter is clogged.

3. Dirty in-line filter.

4. Nozzle is in high pressure mode.

Engine runs good at no- Enginespeed istoo slow.

load but "bogs" when

load is added.

Engine will not start; or

starts and runs rough.

Engine shuts down during

operation.

Engine lacks power.

Engine "hunts" or falters.

I. Dirty air cleaner.

2. Out of gasoline.

3. Stale gasoline.

4. Spark plug wire not connected to

spark plug.

5. Bad spark plug.

6. Water in gasoline.

7. Overchoking.

8. Excessively rich fuel mixture.

9. Intake valve stuck open or closed.

10. Engine has lost compression.

Correction

I. Pull nozzle backward for high pressure

mode.

2. Clear inlet.

3. Provide adequate water flow.

4. Straighten inlet hose, patch leal<.

5. Check and clean inlet hose strainer.

6. Provide cooler water supply.

7. Clear blocks in outlet hose.

8. Replace gun.

9. Clean nozzle.

10. Contact Generac service facility.

I. Insert detergent siphoning tube into

detergent.

2. Clean or replace filter/detergent

siphoning tube.

3. See "Check In-Line Filter" on page 12.

4. Push nozzle forward for low pressure

mode.

Move throttle control to FAST position. If

engine still "bogs down", contact Briggs

service facility.

I. Clean or replace air cleaner.

2. Fill fuel tank.

3. Drain gas tanl<; fill with fresh fuel.

4. Connect wire to spark plug.

5. Replace spark plug.

6. Drain gas tank; fill with fresh fuel.

7. Open choke fully and crank engine.

8. Contact Briggs service facility.

9. Contact Briggs service facility.

10. Contact Briggs service facility.

Out of gasoline. Fill fuel tank.

Dirty air filter.

Choke is opened too soon.

Replace air filter.

Move choke to halfway position until

engine runs smoothly.

Page is loading ...

2 _--_ [

bye& S_'_on _

_ pov/eRp_r_ucrs

PARTS LiST

item Part # Qty.

I NSP

2 187878GS

3 187915GS

4 187916GS

5 23139GS

6 190143GS

7 B2516GS

8 187952GS

9 30809GS

I0 49808GS

I I B2142GS

12 190146GS

13 AI87619GS

14 AI87602GS

15 187918GS

16 191413GS

18 188194GS

19 B3263GS

20 87815GS

21 BB3061BGS

22 187623GS

23 190134GS

24 191457GS

26 B4224GS

27 97837GS

28 190862GS

29 B3335GGS

30 97566GS

3[ 190605GS

32 B5642GS

33 21783GS

36 189970GS

38 A2013GS

39 190750GS

40 52858GS

UNmT

Description

ENGINE

HANDLE, Lift

DECALWarning/Decal

DECAL Start Instructions

KEY

DECALS/BILLBOARD

CARVinyL Black

DECAL, Cool Down

GROMMET

VVASHER

TIRE

NUT, Push

BASE

HANDLE

DECAL, Quick Reference

HOUNT, Vibe

RIVET, Blind

GUN, High Pressure

GOGGLES, Safety

OIL

KIT, Handle Hardware

MANUAL, Owners

MANUAL, Engine

SCREEN, Inlet

O-RING, Hi - Pressure

KIT, Maintenance

VVAN D, Adjustable Nozzle

HANG TAG, Nozzle

NOZZLE

HOSE

VALVE,Thermal Relief

ASSY,Pump (see pages 18-19)

SCREW

NUT

Page is loading ...

2 ---_ ]

bye& S_on _

_7_ POWERP_OUC'S

PARTS UST

Item Part # Qty.

t9 19057_GS

23 190626GS

28 _90627GS

29 _90S75GS

30 _90576GS

34 _90S77GS

45 _9057BGS

46 190579GS

47 _90580GS

62 19058_GS

6B 190582GS

69 _90S84GS

76 21783GS

77 _90586GS

A _90709GS

9 ...... I

II ...... i

12 ...... i

15 ...... i

16 ...... i

70 ...... 3

74 ...... 5

77 ...... i

B 190632GS 0

4 ...... I

8 ...... I

20 ...... I

21 ...... I

22 ...... I

C _90634GS 0

5 ...... I

6 ...... I

D _907_0GS 0

16 ..... I

70 ...... 3

71 ...... 3

72 ...... 3

73 ...... 3

74 ...... S

77 ...... I

E _9059_GS 0

24 ...... 3

25 ...... 3

26 ...... 6

27 ...... 4

44 ...... 4

74 ...... 5

PUMP

Description

CAR Oil

CARTER

MANIFOLD

O-RING

SCREW

CONNECTION, Chemical lnmet

VALVE, Seat Pmate, Brass

VALVE, Seat, Stainless

CAP

BALL, Stainmess Steel

O-RING

TNERMO RELIEF

OIL BOTTLE

KIT,WOBBLE PLATE

BEARING

ASSY,Engine Adapter

FLAT BEARING DISC

ROLLER BEARING

FLAT BEARING DISC

O-RING

SCREW

OUL BOTTLE

KIT, WATER INLET, ALUM

O-RING

WASHER

GARDEN HOSE w/FINGER GRIP

EXTENSION, INLET

WASHER w/FILTER

KIT, OUTLET, ALUM

OUTLET EXTENTION

O-RING

KIT, PISTON

O-RING

SCREW

SPRING

PISTON, Stainless Steel

SPRING PLATE

SCREW

OIL BOTTLE

KIT,CHECK VALVES

O-RING

ASSY.,V_Ive Group

O-RING

SCREW

Item Part #

F t90592GS

37 .....

38 .....

39 .....

40 .....

41 .....

42 .....

43 .....

G 190593GS

31 .....

32 .....

33 .....

34 .....

35 .....

36 ....

N t90594GS

48 .....

49 .....

SO .....

SI .....

52 .....

53 ....

54 .....

55 .....

56 ....

57 .....

58 .....

59 .....

60 .....

61 ....

j t8997tGS

78 ......

79 ......

80 ......

81 ......

K 190595GS

18 .....

61 .....

63 .....

64 .....

65 .....

66 .....

67 .....

74 .....

L t90596GS

44 ......

74 .....

75 ......

Qty.

Description

KIT, INLET CHECK

VALVE, Non-Return

SPRING

INJECTION NOZZLE

O-RING

INJECTION NIPPLE

O-RING

KIT, CHEMICAL INJECTION

SPRING

BALL

O-RING

CONNECTION, Chemical Inlet

O-RING

SCRE\&{ Fitting

KIT, UNLOADER STEM

BACK RING

O-RING

VALVE, By Pass, Brass

PISTON

SPRING, Easy Start

PISTON, Body

RING, Back

SPACER

SPRING, Regulation Press

NUT, Regulation Press

NUT

O-RING

KIT, CHEMICAL NOSE

O-RING

TUBE, Inlet Support

TUBE, Chemical

FILTER

KiT, SEAL SET

O-RING

SEAL

PILOT SPACER, Brass

O-RING

WASHER

SEAL, H.R

SCREW

KiT, HEAD BRASS

SCREW

HEAD, Pump

NOTE: item letters A - L are service kits and include aH

parts shown within the box.

Page is loading ...

LiMiTED WARRANTY

GENEPJkC PORTABLE PRODUCTS OWNERWARRANTY POLICY Effective October 1,2001

LiHiTED WARRANTY

"Generac Portable Products, LLC will repah" or replace, free of charge, any part, or parts of the equipment that are defective in material or

workmanship or both_Transportation charges on parts submitted for" repair or replacement under this Warranty must be borne by purchaser:

This warranty is effective for the time periods and subject to the conditions provided for in this policy. For" warranty service, find the nearest

Authorized Service Dealer in our dealer Iocator map at wwwgenerac-portables.com or call [-877-544-0982.THERE [S NO OTHER EXPRESS

WARRANTY. [MPUED WARRANTIES, [NCLUDINGTHOSE OF HERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE,ARE

LIMITED TO THE TIME PERIOD SPECIFIED, OR TO THE EXTENT PERHITTED BY LAW ANY AND ALL [HPLIED VVARRANTIES ARE

EXCLUDED. LIABILITY FOR CONSEQUENTIAL DAHAGES UNDER ANY AND ALL WARRANTIES ARE EXCLUDED TO THE EXTENT

EXCLUSION [S PERMITTED BY LA\A! Some states do not allow limitations on how long an implied warranty lasts, and some states do not

allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you_This

warranty gives you specific legal rights and you may also have other rights which vary from state to state and country to country"

PRODUCTS**

Portable Generator

(SideValve Engine Powered)

Portable Generator

(Overhead Valve Engine Powered)

Electric Powered Pressure Washer

Gasoline Powered Pressure VVasher

WARRANTY PERIOD*

CONSUMER USE

Iyear

2 years

(2nd year parts only)

I year

COMMERCmAL USE

90 days

I year

None

90 days

_ The warranty period begins on the date of purchase by the first retail consumer" or commercial end user; and continues for the period of time

stated in the table above. "Consumer use" means persona[ residential household use by a retail consumer. "Commercial use" means all other uses,

including use for" commercial income producing or rental purposes. Once equipment has been used commercially, it shah thereafter be considered

to be in commercial use for purposes of this warranty_ Used equipment, demonstration equipment and equipment used for prime power in place

of a utility are not warranted.Accessory parts such as guns_ hoses, wands and nozzles are excluded from the product warrant)s

I_ The gasoline engine and starting batteries are warranted solely by the manufacturers of those products.

WARRANTY REGiSTRATiON iS NOT NECESSARYTO OBTAIN WARRANTY ON GENERAC PORTABLE PRODUCTS

EQUIPMENT. SAVEYOUR PROOF OF PURCHASE RECEIPT. mFYOU DO NOT PROVIDE PROOF OFTHE iNiTiAL

PURCHASE DATE AT THE TIME WARRANTY SERvmcE ms REQUESTED, THE MANUFACTURING DATE OF THE

EQUIPMENTWHLL BE USEDTO DETERMINETHEWARRANTY PERIOD.

About your equipment warranty:

Generac Portable Products welcomes warranty repair and apologizes to you for being inconvenienced.Any Authorized Service Dealer may perform

warranty repairs. Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example,

warranty would not apply if equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper

installation. Similarly, warranty is void if the seria! number of the equipment has been removed or the equipment has been altered or modified_

If a customer" differs with the decision of the Service Dealer, an investigation vviJl be made to determine whether the warranty applies_Ask the

Service Dealer to submit all supporting facts to its Distributor" for review. If the Distributor decides that the claim is iustified, the customer will be

fully reimbursed for those items that are defective.To avoid misunderstandings that might occur between the customer and the Dealer_ listed

below are some of the causes of equipment failure that the warranty does not cover:

Norma_ wear:

Outdoor Power Equipment, like aH mechanical devices, needs periodic parts, service and replacement to perform welLThis warranty

does not cover repair when normal use has exhausted the life of a part or the equipment.

installation and Maintenance:

This warranty does not apply to equipment or" parts that have been subjected to improper" or unauthorized installation or alteradom

misuse, negligence, accident, overloading, overspeeding, improper maintenance, repair or storage so as, in Generac Portable Products'

iudgment, to adversely affect its performance and reliability_This warranty aim does not cover normal maintenance such as adiustments,

fuel system cleaning and obstruction (due to chemical, dirt, carbon or lime, etc.).

Other Exclusions:

Also excluded from this warranty are wear items such as quick couplers, oil gauges, belts, o-rings, filters, pump packing, etc., pumps

which have been run without water supplied or damage or malfunctions resulting from accidents, abuse, modifications, alterations, or

improper servicing or freezing or chemical deterioration_

Warranty is available onmythrough service dealers authorized by Generac Portabme Products.This warranty does not appmy to

service by any other entity.

You may locate your nearest Authorized Generac Portabme Product Service Dealer in our dealer mocator map at

www.generac-portabies.com or call 1=877=$44=0982.

Oenerac Portable Products Are Made Under One Or More Of The Following Patents: (Other Patents Pending) ]

5902094 5823752 5718255 5890413

[

Generac Portabme Products, LLC

jefferson,Wisconsin U.S.A.

Generac Portable Products 2300PSI 1674-0 Owner's manual

Brand: Generac Portable Products

Model: 2300PSI 1674-0

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

español: Generac Portable Products 2300PSI 1674-0 El manual del propietario

Generac Portable Products 2300PSI 1674-0 Owner's manual

This manual is also suitable for

Generac Portable Products 2300PSI 1674-0 Owner's manual

in other languages

Related papers

Other documents