Groupe Brandt DOE505WE1 Owner's manual

DOE505*

DOC505*

FR

Le guide d’utilisation de votre four

User Manual for Your Oven

Betriebsanleitung des Backofens

Gebruikshandleiding van uw oven

Betjeningsvejledning for ovn

Guía de utilización de su horno

O guia de utilização do seu forno

GB

DE

NL

DK

ES

PT

99635881_ML_A DOE505.qxd 07/02/05 13:59 Page 1

2

Tout au long de la notice, vous signale les consignes de sécurité,

vous signale les conseils et les astuces

Edito P.3

Comment se présente votre four ?

Descriptif de l’appareil P.4

Accessoires P.5

Conseils de sécurité P.6

Comment installer votre four ?

Raccordement électrique P.7

Changement du câble d’alimentation P.8

Dimensions utiles pour encastrer votre four P.9

Comment utiliser votre four ?

Le détail de votre programmateur P.10

Comment mettre à l’heure l’horloge du four ? P.11

Comment faire une cuisson immédiate ? P.12

Comment programmer une cuisson ? P.13-14

Comment utiliser le minuteur ? P.15

Modes de cuisson du four P.16-17

Comment entretenir votre four ? P.18

Comment changer l’ampoule ? P.19

Que faire en cas d’anomalies de fonctionnement P.19

Qui contacter ? P.20

Sommaire

99635881_ML_A DOE505.qxd 07/02/05 13:59 Page 2

Page is loading ...

5

Accessoires

AR

AV

Grille sécurité anti basculement

cambrée

Même utilisation que la grille plate.

Sa forme est étudiée pour vous permettre de

positionner votre plat entre 2 niveaux de gradin.

A n'utiliser que sur la grande cavité.

Plat creux + grille

(

lèchefrite)

Inséré sous la grille, il recueille les jus et les

graisses des grillades. Il peut aussi être utilisé

à demi rempli d'eau pour des cuissons au bain-

marie.Evitez de poser directement dans ce plat

des rôtis ou des viandes car vous aurez auto-

matiquement d'importantes projections sur les parois du four.

FR

99635881_ML_A DOE505.qxd 07/02/05 13:59 Page 5

Page is loading ...

10

Comment utiliser votre four ?

SET

1. L

e détail de votre programmateur

Affichage des températures, temps, durées et minuteur

Indicateur d’affichage de la température

Indicateur d’affichage de la durée de cuisson

Indicateur d’affichage de la fin de cuisson

Indicateur d’affichage du minuteur indépendant

Touche d’accès aux différents programmes de réglage

1

3

4

5

6

2

6

2

3

4

5

1

99635881_ML_A DOE505.qxd 07/02/05 13:59 Page 10

11

Comment utiliser votre four ?

a) A la mise sous tension

• L’afficheur clignote à 12h.

• Réglez l’heure à l’aide du sélecteur de réglage

+ ou - (le maintien sur + ou - permet d’obtenir

un défilement rapide).

• Appuyez sur la touche SET pour valider.

Exemple:12h30.

b) Remise à l’heure de l’horloge

• Restez appuyer quelques secondes sur SET,

000 apparait et en continuant à appuyer, l’heure

apparait en clignotant.

• Ajustez le réglage de l’heure avec le sélecteur de

réglage ( + ou –).

• Appuyez sur la touche SET pour valider.

SET

2. Comment mettre à l'heure l’horloge du four ?

S’il n’y a pas de validation par la touche SET, l’enregistrement

est automatique au bout de quelques secondes.

SET

FR

SET

99635881_ML_A DOE505.qxd 07/02/05 13:59 Page 11

Page is loading ...

21

99635881_ML_A DOE505.qxd 07/02/05 14:00 Page 21

22

Throughout the manual, indicates safety recommendations,

indicates advice and tips

Introduction p. 23

What does your oven look like?

Description of the appliance p. 24

Accessories p. 25

Safety recommendations p. 26

How do you install your oven?

Electrical connection p. 27

Changing the power cable p. 28

Useful dimensions for installing your oven p. 29

How does your oven work?

Close-up of your analog programmer p. 30

How do you set the oven clock? p. 31

How do you program for immediate cooking? p. 32

How do you set a cooking programme? pp. 33-34

How does the timer work? p. 35

How do you change the lamp? p. 35

Oven cooking functions pp. 36-37

How do you care for your oven? pp. 38

What to do in case of operating malfunctions p. 39

Table of Contents

99635881_ML_A DOE505.qxd 07/02/05 14:00 Page 22

23

GB

Introduction

Dear Customer,

You have just acquired a DE DIETRICH oven and we would like to thank you.

Our research teams have created a new generation of appliances for you.

Their quality, design and technological advances make them exceptional prod-

ucts and reveal our unique know-how.

With modern, refined lines, your new DE DIETRICH oven blends harmoniously

into your kitchen and perfectly combines technological expertise, cooking per-

formance and aesthetic luxury.

In the line of DE DIETRICH products, you will also find a wide range of hobs,

ventilation hoods, dishwashers, microwave ovens and refrigerators, all of

which can be built in and all of which can be coordinated with your new DE

DIETRICH oven.

Thanks to these "New Items of Value" that serve as guideposts in our every-

day lives, DE DIETRICH, the reference of excellence, is truly an invitation to a

new art of living.

The DE DIETRICH brand.

99635881_ML_A DOE505.qxd 07/02/05 14:00 Page 23

SETSET

5

3

1

24

What does your oven look like?

1

2 5

3

4

Temperature setting

Analog programmer

Function selector

Lamp

Shelf support indicator

DESCRIPTION OF THE APPLIANCE

1

2 3

4

5

99635881_ML_A DOE505.qxd 07/02/05 14:00 Page 24

25

GB

Curved anti-tipping safety grid

Same use as the flat grid

Its shape was designed to allow you to position your

dish between two shelf support levels.

Hollow dish + grid (drip tray)

Inserted under the grid, it catches barbecue juices

and grease. It can also be used half-full of water for

double-boiler cooking methods. Avoid placing roasts

or meats directly in the dish because you are certain

to have major spattering on the oven walls.

Accessories

Rear

Front

99635881_ML_A DOE505.qxd 07/02/05 14:00 Page 25

26

Safety Recommendations

Please become familiar with these recommendations before installing

and using your oven. This oven was designed for use by private persons in their

homes. It is intended solely for cooking foodstuffs. This oven does not contain any

asbestos-based components.

FIRST USE:

Before using your oven for the first time, heat it up while empty with the door

closed for approximately 15 minutes using the maximum setting in order to "cure"

the appliance. The rock wool that surrounds the oven cavity may initially release

a particular odour caused by its composition. Similarly, you may notice the release

of some smoke. All of this is normal.

SUBSEQUENT USES:

- Ensure that the door of your oven is completely closed so that the seal can

properly do its job.

- Do not let anyone lean against or sit on the oven door when it is open.

- When using the grill with the door semi-open, exposed parts and

surfaces may become hot. Keep small children away.

- When in use, the appliance becomes hot. Be careful not to touch the heat-

ing elements located inside the oven.

- After cooking, do not use bare hands to touch the dishes or accessories

(grid, turnspit, drip tray, turnspit support, etc.); use a potholder or heat-resistant

material.

- Do not line your oven with sheets of aluminium. Otherwise, the result

could be an accumulation of heat that could have an undesirable effect on cook-

ing and roasting results and could damage the enamel.

The oven must be turned off for all attempts to clean the cavity.

- During cleaning, the exposed surfaces become hotter than during

normal use. It is advisable to keep small children at bay.

You absolutely must return the function selector to 0 to reuse

your oven.

99635881_ML_A DOE505.qxd 07/02/05 14:00 Page 26

27

GB

H

ow do you install your oven?

Monophase 20A Counter

220-240 V ~ 50 Hz

Two-prong receptacle

+ ground lead

CEI standard 60083

Monophase line 220-240 V ~

Electrical connection

Power cable

approximately

1.5 m in length

16A fuse or differential

circuit breaker

Before making the connection, ensure that the wires in your

electrical set-up have enough cross-sectional area to properly

supply electricity to the appliance.

The fuse in your set-up must be 16 amperes.

The electrical connection should be performed before the appliance is installed in

the cabinet.

• The oven must be connected with a power cable (standardized) with three

1.5 mm² conductors (1 ph +1 N + ground) that must be connected to a

monophase 220-240 V network via a CEI 60083 standardized receptacle (1 ph

+1 N + ground lead) or in accordance with installation rules. The safety wire

(green-yellow) is connected to the appliance's terminal and must be connected

to the ground lead of the electrical set-up.

• In the case of connections with an electric receptacle, it must remain accessible

after installation of the appliance.

• The oven's neutral conductor (blue wire) must be connected to the network's

neutral conductor.

99635881_ML_A DOE505.qxd 07/02/05 14:00 Page 27

28

• The power cable (H05 RR-F, H05 RN-F or H05 VV-F) must be of sufficient length to

be connected to the build-in oven while it sits on the floor in front of the cabinet.

To do this the appliance must be disconnected from the electrical network:

• Open the inspection flap located at the lower right of the back cover by

unscrewing the two screws, then pivot the inspection flap.

• Strip 12 mm along each wire of the new power cable.

• Carefully twist together the strands.

• Loosen the screws from the terminal board and remove the power cord to be

replaced.

• Introduce the power cable through the side of the cover in the cable clip located

to the right of the terminal board.

• Connect the cable wires in accordance with the written markings on the terminal

board.

• All the strands of the electricity wires must be captured under the screws.

• The phase wire on the L terminal.

• The green-yellow coloured ground wire should be connected to the terminal .

• The neutral conductor (blue) on the N terminal.

• Screw down tightly the screws on the terminal board and check the connection

by pulling on each wire.

• Attach the cable with the cable clip located to the right of the terminal board.

• Close the inspection flap using the two screws.

Changing the power cable

We cannot be held responsible for any accident resulting from

an inexistent, defective or incorrect ground lead.

How do you install your oven?

99635881_ML_A DOE505.qxd 07/02/05 14:00 Page 28

29

GB

How do you install your oven?

To be certain that you have a proper installation, do not hesitate

to call on a household appliance specialist.

Useful dimensions for installing your oven

The oven can be installed under a worktop or in a column of cabinetry

(open* or closed) having the appropriate dimensions for built-in installa-

tion (see adjacent diagram).

Your oven has optimised air circulation that allows it to achieve remarkable cooking

and cleaning results if the following guidelines are respected:

• Centre the oven in the cabinet so as to guarantee a minimum distance of 5 mm

between the appliance and the neighbouring cabinet.

• The material of the built-in cabinetry must be heat resistant (or be covered with

such a material).

• For greater stability, attach the oven in the cabinet with two screws through the

holes provided for this purpose on either side of the front inner panel (see diagram).

To do this:

1) Remove the rubber screw covers to access the mounting holes.

2) Drill a Ø 3 mm hole in the cabinet panel to avoid splitting the wood.

3) Attach the oven with the two screws.

4) Replace the rubber screw covers (they also serve to absorb the shock caused by

closing the oven door).

(*) If the cabinet is open, its opening must be 70 mm (maximum).

70

550

Location of

attachment

screw

Location of

attachment

screw

50mm x 50mm cut-out

99635881_ML_A DOE505.qxd 07/02/05 14:00 Page 29

30

How does your oven work?

1. Close-up of your analog programmer

Display for temperatures, times, cooking times and timer

Temperature display indicator

Cooking time display indicator

End of cooking display indicator

Independent timer display indicator

Touch control for accessing various time setting programmes

1

3

4

5

6

2

SET

6

2

3

4

5

1

99635881_ML_A DOE505.qxd 07/02/05 14:00 Page 30

31

GB

a) When supplied with electricity

• The display flashes.

• Set the time by turning the + or – selector (contin-

ual turning of the + or – selector allows for rapid

number advancement)

• Press the SET touch control to enter.

Example: 12:30.

b) Resetting the clock time

• Press SET for a few seconds then release.

The display flashes.

• Adjust the time with the selector (+ or –).

• Press the SET touch control to enter.

2.

How do you set the oven clock?

If the SET touch control is not pressed, the adjustment

will be automatically recorded after a few seconds.

How does your oven work?

SET

99635881_ML_A DOE505.qxd 07/02/05 14:00 Page 31

32

How does your oven work?

3.

How do you program for immediate cooking?

The analog programmer should display only the time; it should not be flashing.

• Choose the cooking mode:

Turn the function selector to the position of your

choice.

Example: position " "-> the oven turns on.

Your oven recommends the most commonly used tem-

perature.

Place your dish in the oven based on the recommen-

dations provided by the cookbook.

It is, however, possible to adjust the temperature by turn-

ing the selector toward + or –.

Example " " set to 210°.

After these steps, the oven begins to heat up and the display alternates between

the temperature in the oven and the temperature selected.

A series of beeps will be emitted when the oven reaches the selected tempera-

ture.

Once this temperature is reached, it remains on the display.

After a cooking cycle, the circulating fan continues to function for a

period in order to cool the oven.

SET

99635881_ML_A DOE505.qxd 07/02/05 14:00 Page 32

33

GB

How does your oven work?

4. How do you set a cooking programme?

a) With immediate start

1. Set the desired cooking mode and adjust the tempera-

ture if necessary.

Example: position “ ”

Temperature 200°C.

2. Press the SET touch control until the cooking time indi-

cator flashes “ ”.

The display flashes 0:00 to indicate that you can now

adjust the setting.

3. Turn the + or - selector to set the desired time.

Example: 25 min cooking time.

The cooking time is automatically recorded after a few sec-

onds -> the display no longer flashes and returns to tem-

perature display mode.

The countdown of the length of time begins immediately

after it has been set.

After these three steps, the oven heats up:

A series of beeps will be emitted when the oven reaches the selected temperature.

At the end of cooking (end of programmed time),

- the oven stops

- the cooking time indicator turns off

- 0:00 is displayed

- a series of beeps is emitted for a few minutes.

The beeping sound stops definitively when the function selector is reset to 0.

After a cooking cycle, the circulating fan continues to function for a

period in order to cool the oven.

SET

99635881_ML_A DOE505.qxd 07/02/05 14:00 Page 33

34

How does your oven work?

b) With delayed start (choose end time)

Proceed as with programmed cooking.

After setting the cooking time,

Press the SET touch control until the end of cooking

indicator flashes “ ”.

The display flashes 0:00 to indicate that you can now

adjust the setting.

Turn the + or – selector to set the desired cooking

end time.

Example: End of cooking at 13:00.

After these steps, the oven heating is delayed so that

cooking ends at 13:00.

At the end of cooking (end of programmed time),

- The oven stops

- The cooking time indicator turns off

- 0:00 is displayed

- A series of beeps is emitted for a few minutes.

The beeping sound stops definitively when the function selector is reset to 0.

After a cooking cycle, the circulating fan continues to function for a

period in order to cool the oven.

In the case of pre-programmed cooking the oven cavity is lit until cooking begins

and once cooking is finished.

In the case of pre-programmed, fan-assisted cooking, if the function selector is not

reset to 0, the fan continues to operate in order to even out the temperature in

the oven.

SET

99635881_ML_A DOE505.qxd 07/02/05 14:00 Page 34

35

GB

5. How do you use the timer?

Your oven is equipped with an electronic timer that is independent of the

oven functions, making it possible to measure times.

In this case, the timer display takes priority over the time

of day and temperature display.

Press the SET touch control until the timer indicator

flashes -> the display flashes.

Turn the selector (+ or –) until the desired time is

displayed (60 minutes maximum).

The display stops flashing after a few seconds or after the

SET touch control is pressed and the timer starts working,

counting down the time in seconds.

Once the time has expired, the timer emits a series of

beeps to notify you.

It is possible to change or cancel the timer programme at any

time.

• The lamp is located on the ceiling of your oven's cavity.

a) Unscrew the view port (see adjacent

diagram).

b) Unscrew the lamp in the same direction.

Lamp specifications:

- 15 W

- 220-240 V

- 300°C

- E 14 cap

c) Replace the lamp then reposition the

view port and reconnect your oven.

How do you change the lamp?

Lamp

Unscrew

View port

To unscrew the view port and the lamp, use a rubber glove,

which will make disassembly easier.

Disconnect your oven before performing any task on the lamp

to avoid the risk of electric shock and, if necessary, let the

appliance cool down.

SET

99635881_ML_A DOE505.qxd 07/02/05 14:01 Page 35

Page is loading ...

Groupe Brandt DOE505WE1, DOC505XE1, DOE505BE1, DOE505XD1, DOE505XE1 Owner's manual

Related papers

Other documents