Vollrath Grinder User manual

Brand: Vollrath

Model: Grinder

Category: Mincers

Type: User manual

Operator’s Manual

Electric Meat Grinders

2018 The Vollrath Company L.L.C. Part No. 2350138-1 ml 3/13/18

fry pan.

Thank you for purchasing this Vollrath equipment. Before operating the

equipment, read and familiarize yourself with the following operating

and safety instructions. SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE. Save the original box and packaging. Use this packaging

to ship the equipment if repairs are needed.

SAFETY PRECAUTIONS

To ensure safe operation, read the following statements and understand

their meaning. This manual contains safety precautions which are

explained below. Please read carefully.

Warning is used to indicate the presence of a hazard that will or can

cause severe personal injury or death.

Caution is used to indicate the presence of a hazard that will or can

cause minor or major personal injury if the caution is ignored.

NOTICE: Notice is used to note information that is important but not

hazard-related.

To reduce risk of injury or damage to the equipment:

• Plug only into grounded electrical outlets matching the nameplate

rated voltage.

• Do not operate unattended.

• Do not operate equipment in public areas and/or around children.

• Do not use an extension cord with this equipment. Do not plug this

equipment into a power strip or multi-outlet power cord.

• Check equipment before each use to insure the equipment is clean.

• Wear proper apparel. Do not wear loose fitting or hanging garments

while operating this equipment.

• Use equipment in a flat, level position.

• Unplug equipment, turn off and let it cool before cleaning or moving.

• Do not spray controls or outside of equipment with liquids or

cleaning agents.

• Do not clean the equipment with steel wool.

• Keep equipment and power cord away from open flames, electric

burners or excessive heat.

• Do not operate if equipment has been damaged or is malfunctioning

in any way.

FUNCTION AND PURPOSE

This equipment is intended to grind food products and meat in

commercial foodservice operations only. It is not intended for

household, industrial or laboratory use.

UNPACKING THE EQUIPMENT AND INITIAL SETUP

1. Remove all packing material and tape, as well as any protective

plastic from the equipment.

2. Clean any glue residue left over from the plastic or tape.

3. When no longer needed, dispose of all packaging and materials in an

environmentally-responsible manner.

WARNING

CAUTION

Item No. Model Description

40743 MIN0012 Grinder No. 12

40744 MIN0022 Grinder No. 22

40743

40744

2 Electric Meat Grinders Operator’s Manual

FEATURES AND CONTROLS

BEFORE FIRST USE

1. Disassemble the grinder. See “Disassembly” on page 3.

2. Wash the components. See “Cleaning” on page 4.

3. Assemble the components.

4. Attach the handle to the top of the meat grinder body.

PREPARE THE FOOD

1. For vegetables, remove stalks and stems; for meat, remove all the

skin and bones.

2. Cut the food product into appropriately-sized pieces for grinding.

OPERATION

NOTICE: Using a voltage other than the nameplate rated voltage will

cause damage to the unit. Incorrect voltage, modification

to the power cord or electrical components can damage

unit and will void the warranty.

1. Verify the grinder chamber is seated correctly on the main body.

Tighten the thumbscrew counter-clockwise until secure.

NOTICE: Do not use a tool to tighten the thumbscrew. Hand tighten

only.

2. Place the tray on the top of the grinder chamber.

3. Turn the control switch to the “FORWARD” position.

4. Use the food pusher to push the food product into grinder chamber.

Never use your fingers, hands or other objects to push food through

the grinder.

5. Feed the food into the grinder at a rate that the grinder will accept.

NOTICE: Do not force too much food product into the grinder

chamber. It can overload the grinder, causing it to stop.

6. When grinding is complete, turn the control switch to the “OFF”

position.

A Tray. Funnels or flows the food product to the grinder chamber.

B Faceplate. Holds the grinder plate in place.

C Grinder Chamber. Grinds the food product and houses the

worm gear, blade, grinder plate and faceplate nut.

D Food Pusher. Used to push the food into the grinder chamber.

E Reset Button. If the grinder becomes overloaded, this button

needs to be manually reset after allowing the unit to cool.

F Control Switch. Switches the motor to “FORWARD,”

“REVERSE” or “OFF.”

G Funnel. Use to funnel food into the grinder chamber.

H Main Body. Houses the motor, switch and other components.

I Thumb Screw. Holds the grinder chamber to the main body.

WARNING

Entanglement Hazard

Never place fingers, hands or other objects into the feed chute

other than the food pusher provided with the appliance. Injury

and product damage will occur.

WARNING

Electrical Shock Hazard

Keep water and other liquids from entering the inside of the

equipment. Liquid inside the equipment could cause an

electrical shock.

Electric Meat Grinders Operator’s Manual 3

DISASSEMBLY

1. Turn the control switch to the “OFF” position and unplug the grinder.

2. Remove the grinder chamber assembly from the body of the grinder.

3. Unscrew the faceplate from the grinder head assembly.

4. Remove the grinder plate from the blade shaft.

5. Carefully remove the knife blade from the blade shaft.

6. Remove the worm gear assembly from the grinder head assembly.

7. Remove the washer

ASSEMBLY

1. Assemble the blade shaft assembly into the worm gear.

2. Inspect the shaft washer for wear. Replace if necessary.

3. Slide the shaft washer onto the worm gear shaft so that it is seated

against the worm gear assembly. Slide the worm gear assembly into

the grinder chamber until it is seated fully.r

4. Position the knife blade so the flat edges face outward. Then Slide

the knife blade onto the blade shaft so that it seats completely over

the square end of the worm gear

5. Place the grinder plate onto the blade shaft so that the cutout slides

over the locating pin.

6. If using a sausage filler, place it between the faceplate and the

grinder head assembly.

7. Thread the faceplate onto the grinder head assembly. Tighten

securely.

2018 The Vollrath Company L.L.C. Part No. 2350138-1 ml 3/13/18

www.vollrath.com

The Vollrath Company, L.L.C.

1236 North 18th Street

Sheboygan, WI 53081-3201 U.S.A.

Main Tel: 800.624.2051 or 920.457.4851

Main Fax: 800.752.5620 or 920.459.6573

Customer Service: 800.628.0830

Canada Customer Service: 800.695.8560

Technical Services

[email protected]

Induction Products: 800.825.6036

Countertop Warming Products: 800.354.1970

All Other Products: 800.628.0832

CLEANING

NOTICE: Do not use abrasive materials, scratching cleansers or

scouring pad to clean the exterior of the equipment.

These can damage the finish.

To maintain the appearance and increase the service life, clean this

equipment daily.

1. Turn off and unplug the grinder

2. Wash all components in the dishwasher or a in a solution of mild

dish soap and hot water.

3. Use a damp soft cloth to wipe the exterior of the grinder.

TROUBLESHOOTING

SERVICE AND REPAIR

Serviceable parts are available on Vollrath.com.

To avoid serious injury or damage, never attempt to repair the unit or

replace a damaged power cord yourself. Do not send units directly to

The Vollrath Company LLC. Please contact Vollrath Technical Services

for instructions.

When contacting Vollrath Technical Services, please be ready with the

item number, model number (if applicable), serial number, and proof of

purchase showing the date the unit was purchased.

WARRANTY STATEMENT FOR THE VOLLRATH CO.

This warranty does not apply to products purchased for personal,

family or household use, and The Vollrath Company LLC does not offer

a written warranty to purchasers for such uses.

The Vollrath Company LLC warrants the products it manufactures or

distributes against defects in materials and workmanship as specifically

described in our full warranty statement. In all cases, the warranty runs

from the date of the end user’s original purchase date found on the

receipt. Any damages from improper use, abuse, modification or

damage resulting from improper packaging during return shipment for

warranty repair will not be covered under warranty.

For complete warranty information, product registration and new

product announcement, visit www.vollrath.com.

WARNING

Electrical Shock Hazard

Keep water and other liquids from entering the inside of the

equipment. Liquid inside the equipment could cause an

electrical shock. Do not spray water or cleaning products.

Liquid could contact the electrical components and cause a

short circuit or an electrical shock.

Problem Might be Caused By Course of Action

Grinder stops operating or output is erratic. Grinder is overloaded. Switch to the “REVERSE” position momentarily, then turn the unit

to the “OFF” position. Check the following:

• Thumbscrew too tight; loosen and hand-tighten, do not over-

tighten.

• Discharge plate is blocked; remove and clear.

• Blade edges are dull; have sharpened or replace.

• Overloading and motor stops; allow unit to cool and press reset

button.

Press the Reset button.

Blade is installed backwards. Correct blade direction.

Metal shavings or particles in food product. Blade is installed backwards. Correct blade direction.

Motor hums but does not operate. Governor out of adjustment.

Adjust governor per procedures posted at Vollrath.com or contact

Vollrath Technical Service.

Page is loading ...

Vollrath Grinder User manual

Brand: Vollrath

Model: Grinder

Category: Mincers

Type: User manual

Download PDF

report

in other languages

français: Vollrath Grinder Manuel utilisateur
español: Vollrath Grinder Manual de usuario

Vollrath Grinder User manual

Vollrath Grinder User manual

in other languages

Related papers

Other documents