ARP Cutout switch and Coupling Insulator Installation guide
- Type
- Installation guide
ARP Cutout switch and Coupling Insulator is an electrical device that is used to connect and disconnect electrical circuits. It is typically used in high-voltage applications, such as power distribution systems. The device is designed to be safe and reliable, and it meets all applicable industry standards.
The ARP Cutout switch and Coupling Insulator has a number of features that make it a valuable tool for electrical contractors and other professionals. These features include:
- High-voltage rating: The device is rated for use in circuits with voltages up to 15 kV.
- Compact design: The device is small and lightweight, making it easy to install and transport.
ARP Cutout switch and Coupling Insulator is an electrical device that is used to connect and disconnect electrical circuits. It is typically used in high-voltage applications, such as power distribution systems. The device is designed to be safe and reliable, and it meets all applicable industry standards.
The ARP Cutout switch and Coupling Insulator has a number of features that make it a valuable tool for electrical contractors and other professionals. These features include:
- High-voltage rating: The device is rated for use in circuits with voltages up to 15 kV.
- Compact design: The device is small and lightweight, making it easy to install and transport.
6110 Lamb Road • Wyoming, NY 14591 www.arp-hivoltageinsulators.com
Phone: 585.495.6231 • Fax: 585.495.6526 email: [email protected]
Camden Printing Form 25169 - Rev. 8-15
Installation Guide
The Assembled Coupling Insulator
& Fuse Cutout Switch
☞ INTRODUTION
Thank you for your cooperation to use our products.
This construction guide is for safety assembled coupling insulator and fuse cutout
switch. Whenever using the items, you must remember contents of construction
guide and use properly.
☞ CONFIGURATION
Part A Part B
☞ CAUTION
1. To installed the products safety, you must read the construction guide.
2. Don fix and disassemble intentionally, when maintaining and repairing.
3. To be safe, please the specialists having electronic wiring.
☞ NOTICE
Following safety instruction…
If you do not understand any portion of this construction guide and need
assistance, contact manufacturer.
Thoroughly and carefully read this guide before installation.
▶ Additional copies
If you need additional copies of this instruction guide, contact your nearest sales
Office, Authorized Distributor, or Headquarters.
▶ Coupling insulator for fuse cutout switch.
INTRODUCTION and CAUTION
• Thank you for purchasing our Cutout Switch &
Coupling Insulator
• Please read and use the Step by Step instructions
on the following page to assemble & install the
components
• These installation instructions are important to safely
and properly install the Cutout Switch &
Coupling Insulator to a Nema Type mounting bracket
• If you do not understand any portion of this
installation guide and need assistance please
contact “ARP” customer service at the address &
contact information below.
CONFIGURATION
Installed on Mounting Bracket
Div. of TMP Technologies Inc.
Advanced Rubber Products
Installation Instructions for Attaching Cutout
& Coupling Insulator to Mounting Bracket
™
6110 Lamb Road • Wyoming, NY 14591 www.arp-hivoltageinsulators.com
Phone: 585.495.6231 • Fax: 585.495.6526 email: [email protected]
Div. of TMP Technologies Inc.
Advanced Rubber Products
Camden Printing Form 25169 - Rev. 8-15
Installation Instructions for Attaching Cutout
& Coupling Insulator to Mounting Bracket
Part A. Install guide with coupling insulator and mounting bracket Part B. Install guide with coupling insulator and cutout switch
☞ Carriage bolt installed in coupling insulator
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Coupling insulator
Fuse cutout switch
Lock washer
Plain washer
☞ Carriage bolt installed in mounting bracket.
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Plain washer
Mounting bracket
External-tooth lockwasher
Lock washer
Coupling insulator
Step 2
☞ Fuse cutout switch installed on the terminal of coupling
insulator
(Note. Located between the grooves of the terminal)
Step 3
☞ Plain washer/lock washer & nut installation.
Step 4
☞ Check the installed fuse cutout switch.
Step 2
☞ The external-tooth lockwasher is into the carriage bolt.
(Note. The placement of the external-tooth lockwasher
between the fuse cutout center insert and the bracket)
☞ Coupling insulator installation.
(Note. Under the flat portion of terminal of
coupling insulator)
Step 3
☞ Plain washer/lock washer
& nut installation.
Step 4
Part A. Install guide with coupling insulator and mounting bracket Part B. Install guide with coupling insulator and cutout switch
☞ Carriage bolt installed in coupling insulator
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Coupling insulator
Fuse cutout switch
Lock washer
Plain washer
☞ Carriage bolt installed in mounting bracket.
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Plain washer
Mounting bracket
External-tooth lockwasher
Lock washer
Coupling insulator
Step 2
☞ Fuse cutout switch installed on the terminal of coupling
insulator
(Note. Located between the grooves of the terminal)
Step 3
☞ Plain washer/lock washer & nut installation.
Step 4
☞ Check the installed fuse cutout switch.
Step 2
☞ The external-tooth lockwasher is into the carriage bolt.
(Note. The placement of the external-tooth lockwasher
between the fuse cutout center insert and the bracket)
☞ Coupling insulator installation.
(Note. Under the flat portion of terminal of
coupling insulator)
Step 3
☞ Plain washer/lock washer
& nut installation.
Step 4
Part A. Install guide with coupling insulator and mounting bracket Part B. Install guide with coupling insulator and cutout switch
☞ Carriage bolt installed in coupling insulator
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Coupling insulator
Fuse cutout switch
Lock washer
Plain washer
☞ Carriage bolt installed in mounting bracket.
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Plain washer
Mounting bracket
External-tooth lockwasher
Lock washer
Coupling insulator
Step 2
☞ Fuse cutout switch installed on the terminal of coupling
insulator
(Note. Located between the grooves of the terminal)
Step 3
☞ Plain washer/lock washer & nut installation.
Step 4
☞ Check the installed fuse cutout switch.
Step 2
☞ The external-tooth lockwasher is into the carriage bolt.
(Note. The placement of the external-tooth lockwasher
between the fuse cutout center insert and the bracket)
☞ Coupling insulator installation.
(Note. Under the flat portion of terminal of
coupling insulator)
Step 3
☞ Plain washer/lock washer
& nut installation.
Step 4
Part A. Install guide with coupling insulator and mounting bracket Part B. Install guide with coupling insulator and cutout switch
☞ Carriage bolt installed in coupling insulator
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Coupling insulator
Fuse cutout switch
Lock washer
Plain washer
☞ Carriage bolt installed in mounting bracket.
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Plain washer
Mounting bracket
External-tooth lockwasher
Lock washer
Coupling insulator
Step 2
☞ Fuse cutout switch installed on the terminal of coupling
insulator
(Note. Located between the grooves of the terminal)
Step 3
☞ Plain washer/lock washer & nut installation.
Step 4
☞ Check the installed fuse cutout switch.
Step 2
☞ The external-tooth lockwasher is into the carriage bolt.
(Note. The placement of the external-tooth lockwasher
between the fuse cutout center insert and the bracket)
☞ Coupling insulator installation.
(Note. Under the flat portion of terminal of
coupling insulator)
Step 3
☞ Plain washer/lock washer
& nut installation.
Step 4
Part A. Install guide with coupling insulator and mounting bracket Part B. Install guide with coupling insulator and cutout switch
☞ Carriage bolt installed in coupling insulator
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Coupling insulator
Fuse cutout switch
Lock washer
Plain washer
☞ Carriage bolt installed in mounting bracket.
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Plain washer
Mounting bracket
External-tooth lockwasher
Lock washer
Coupling insulator
Step 2
☞ Fuse cutout switch installed on the terminal of coupling
insulator
(Note. Located between the grooves of the terminal)
Step 3
☞ Plain washer/lock washer & nut installation.
Step 4
☞ Check the installed fuse cutout switch.
Step 2
☞ The external-tooth lockwasher is into the carriage bolt.
(Note. The placement of the external-tooth lockwasher
between the fuse cutout center insert and the bracket)
☞ Coupling insulator installation.
(Note. Under the flat portion of terminal of
coupling insulator)
Step 3
☞ Plain washer/lock washer
& nut installation.
Step 4
Part A. Install guide with coupling insulator and mounting bracket Part B. Install guide with coupling insulator and cutout switch
☞ Carriage bolt installed in coupling insulator
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Coupling insulator
Fuse cutout switch
Lock washer
Plain washer
☞ Carriage bolt installed in mounting bracket.
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Plain washer
Mounting bracket
External-tooth lockwasher
Lock washer
Coupling insulator
Step 2
☞ Fuse cutout switch installed on the terminal of coupling
insulator
(Note. Located between the grooves of the terminal)
Step 3
☞ Plain washer/lock washer & nut installation.
Step 4
☞ Check the installed fuse cutout switch.
Step 2
☞ The external-tooth lockwasher is into the carriage bolt.
(Note. The placement of the external-tooth lockwasher
between the fuse cutout center insert and the bracket)
☞ Coupling insulator installation.
(Note. Under the flat portion of terminal of
coupling insulator)
Step 3
☞ Plain washer/lock washer
& nut installation.
Step 4
Part A. Install guide with coupling insulator and mounting bracket Part B. Install guide with coupling insulator and cutout switch
☞ Carriage bolt installed in coupling insulator
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Coupling insulator
Fuse cutout switch
Lock washer
Plain washer
☞ Carriage bolt installed in mounting bracket.
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Plain washer
Mounting bracket
External-tooth lockwasher
Lock washer
Coupling insulator
Step 2
☞ Fuse cutout switch installed on the terminal of coupling
insulator
(Note. Located between the grooves of the terminal)
Step 3
☞ Plain washer/lock washer & nut installation.
Step 4
☞ Check the installed fuse cutout switch.
Step 2
☞ The external-tooth lockwasher is into the carriage bolt.
(Note. The placement of the external-tooth lockwasher
between the fuse cutout center insert and the bracket)
☞ Coupling insulator installation.
(Note. Under the flat portion of terminal of
coupling insulator)
Step 3
☞ Plain washer/lock washer
& nut installation.
Step 4
Part A. Install guide with coupling insulator and mounting bracket Part B. Install guide with coupling insulator and cutout switch
☞ Carriage bolt installed in coupling insulator
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Coupling insulator
Fuse cutout switch
Lock washer
Plain washer
☞ Carriage bolt installed in mounting bracket.
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Plain washer
Mounting bracket
External-tooth lockwasher
Lock washer
Coupling insulator
Step 2
☞ Fuse cutout switch installed on the terminal of coupling
insulator
(Note. Located between the grooves of the terminal)
Step 3
☞ Plain washer/lock washer & nut installation.
Step 4
☞ Check the installed fuse cutout switch.
Step 2
☞ The external-tooth lockwasher is into the carriage bolt.
(Note. The placement of the external-tooth lockwasher
between the fuse cutout center insert and the bracket)
☞ Coupling insulator installation.
(Note. Under the flat portion of terminal of
coupling insulator)
Step 3
☞ Plain washer/lock washer
& nut installation.
Step 4
Part A. Install guide with coupling insulator and mounting bracket Part B. Install guide with coupling insulator and cutout switch
☞ Carriage bolt installed in coupling insulator
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Coupling insulator
Fuse cutout switch
Lock washer
Plain washer
☞ Carriage bolt installed in mounting bracket.
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Plain washer
Mounting bracket
External-tooth lockwasher
Lock washer
Coupling insulator
Step 2
☞ Fuse cutout switch installed on the terminal of coupling
insulator
(Note. Located between the grooves of the terminal)
Step 3
☞ Plain washer/lock washer & nut installation.
Step 4
☞ Check the installed fuse cutout switch.
Step 2
☞ The external-tooth lockwasher is into the carriage bolt.
(Note. The placement of the external-tooth lockwasher
between the fuse cutout center insert and the bracket)
☞ Coupling insulator installation.
(Note. Under the flat portion of terminal of
coupling insulator)
Step 3
☞ Plain washer/lock washer
& nut installation.
Step 4
Part A. Install guide with coupling insulator and mounting bracket Part B. Install guide with coupling insulator and cutout switch
☞ Carriage bolt installed in coupling insulator
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Coupling insulator
Fuse cutout switch
Lock washer
Plain washer
☞ Carriage bolt installed in mounting bracket.
(Note. Under the head of carriage bolt )
Step 1
Carriage bolt
Plain washer
Mounting bracket
External-tooth lockwasher
Lock washer
Coupling insulator
Step 2
☞ Fuse cutout switch installed on the terminal of coupling
insulator
(Note. Located between the grooves of the terminal)
Step 3
☞ Plain washer/lock washer & nut installation.
Step 4
☞ Check the installed fuse cutout switch.
Step 2
☞ The external-tooth lockwasher is into the carriage bolt.
(Note. The placement of the external-tooth lockwasher
between the fuse cutout center insert and the bracket)
☞ Coupling insulator installation.
(Note. Under the flat portion of terminal of
coupling insulator)
Step 3
☞ Plain washer/lock washer
& nut installation.
Step 4
Step 1: Once Mounting Bracket is attached to the
Cross Arm the Carriage Bolt is installed from bottom
of mounting bracket
Step 2: The external star washer is placed onto the
carriage bolt to go between the Mounting Bracket &
Coupling Insulator
Step 3: Coupling Insulator End Fitting is placed at
surface down above the Star Washer
Step 4: Flat Washer, Lock
Washer & Nut are threaded
onto Carriage Bolt and
Torqued to 40ft/lbs.
Step 1: Carriage Bolt is installed with head of bolt
thru at side of Coupling Insulator
Step 2: Cutout Switch is placed over the Carriage
bolt and registered by the recessed area of the
Coupling Switch
Step 3: Flat Washer, Lock Washer & Nut are
threaded onto Carriage Bolt and Torqued to 40ft/lbs.
Step 4: Verify all Bolts are tight and Cutout is
ready for Connection of all Cables
Carriage Bolt
Lock washer
Plain washer
Mounting bracket
Coupling insulator
External-tooth lockwasher
Plain washer
Lock washer
Carriage BoltCoupling insulator
Fuse cutout switch
Part A: Installing Coupling Insulator to Nema Mounting Bracket Part B: Installing Coupling Insulator to Cutout Switch
Torque to 40ft/lbs
Part
A. Install guide with coupling insulator and mounting bracket
Part
B. Install guide with coupling insulator and cutout
switch
☞
Carriage bolt installed in coupling insulator
(Note
. Under the head of carriage bolt )
Step 1
Carriage bolt
Coupling insulator
Fuse cutout switch
Lock washer
Plain washer
☞
Carriage bolt installed in mounting bracket.
(Note
. Under the head of carriage bolt )
Step 1
Carriage bolt
Plain washer
Mounting bracket
External
-
tooth lockwasher
Lock washer
Coupling insulator
Step 2
☞
Fuse cutout switch installed on the terminal of coupling
insulator
(Note
. Located between the grooves of the terminal)
Step 3
☞
Plain washer/lock washer & nut installation.
Step 4
☞
Check the installed fuse cutout switch.
Step 2
☞
The external
-
tooth lockwasher is into the carriage bolt.
(Note
. The placement of the external
-
tooth lockwasher
between the fuse cutout center insert and the bracket)
☞
Coupling insulator installation.
(Note
. Under the flat portion of terminal of
coupling insulator)
Step 3
☞
Plain washer/lock washer
& nut installation.
Step 4
Torque to 40ft/lbs
Part A.
Install guide with coupling insulator and mounting bracket
Part B. Install guide with coupling insulator and cutout
switch
☞
Carriage bolt installed in coupling insulator
(Note
. Under the head of carriage bolt )
Step 1
Carriage bolt
Coupling insulator
Fuse cutout switch
Lock washer
Plain washer
☞
Carriage bolt installed in mounting bracket.
(Note
. Under the head of carriage bolt )
Step 1
Carriage bolt
Plain washer
Mounting bracket
External
-tooth lockwasher
Lock washer
Coupling insulator
Step 2
☞
Fuse cutout switch installed on the terminal of coupling
insulator
(Note
. Located between the grooves of the terminal)
Step 3
☞
Plain washer/lock washer & nut installation.
Step 4
☞
Check the installed fuse cutout switch.
Step 2
☞
The external
-
tooth lockwasher is into the carriage bolt.
(Note
. The placement of the external
-tooth lockwasher
between the fuse cutout center insert and the bracket)
☞
Coupling insulator installation.
(
Note
. Under the flat portion of terminal of
coupling insulator)
Step 3
☞
Plain washer/lock washer
& nut installation.
Step 4
™
-
1
-
2
ARP Cutout switch and Coupling Insulator Installation guide
- Type
- Installation guide
ARP Cutout switch and Coupling Insulator is an electrical device that is used to connect and disconnect electrical circuits. It is typically used in high-voltage applications, such as power distribution systems. The device is designed to be safe and reliable, and it meets all applicable industry standards.
The ARP Cutout switch and Coupling Insulator has a number of features that make it a valuable tool for electrical contractors and other professionals. These features include:
- High-voltage rating: The device is rated for use in circuits with voltages up to 15 kV.
- Compact design: The device is small and lightweight, making it easy to install and transport.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
PEAK-System PLIN-USB Operating instructions
-
Trust 14591 Datasheet
-
PEAK PLIN-USB User manual
-
Sears 917254460 User manual
-
Lincoln Electric NA-3N Operating instructions
-
Hubbell Standard Cutout Operating instructions
-
-
ESAB HWM-3 Contour Welder Troubleshooting instruction
-
Simplicity Baron / 2400 User manual
-
