Groupe Brandt SL2810 Owner's manual

FR GUIDE D'INSTALLATION ET D'UTILISATION

EN INSTRUCTION FOR USE

NL GEBRUIKSAANWIJZING

Réfrigérateur

Refrigerator

Ijkast

PT MANUAL DE INSTRUÇOES

Frigorífico

CS NÁVOD K INSTALACI A OBSLUZE

HU HASZNÁLATI ÚTMUTATÓ

Chladnièka

RU ÈÍÑÒÐÓÊÖÈÈ ÏÎ ÝÊÑÏËÓÀÒÀÖÈÈ

Fagyasztószekrény

PL INSTRUKCJA DO U¯YCIE

Õîëîäèëüíèêà

Lodówka

Page is loading ...

GENERAL INFORMATION

GB

Refrigerators represents a compressor refrigerators made as a cabinet and

designed for a short-term storage of chilled products.

The moderate class "N" climatic version of the refrigerators is intended

to be used under domestic conditions.

The manufacturer guarantees its troublefree operation at ambient

temperature of +16

o

C to + 32°C.

The refrigerators meet up-to-date requirements for household refrigerators

and electrical devices.

The refrigerant blowing agent is ecolable - it hasn't ozone

layer demolishing materials.

In the ap

pliance can be useed the refrigerant R600 a.

All the required preventive maintenance operations and repairs should

be carried out by an expert in this kind of equipment.

Since efforts are continually made to improve the reliability and performance

of the product, minor changes may be introduced without special notice in these

instruction.

SAFETY PRECAUTIONS

Prior to the refrigerator connection to the mains make sure, that the

power cord is not damaged.

The plug of refrigerator should be connected to properly fixed, stationary

socket providing good contact. The socket must have earth connection.

In case that refrigerator is produced with special supply cord it

could be exchanged by same producer‘s provided special supply cord.

Clean parts located at the refrigerator rear wall from dust accumulated

there using a dry brush or a vacuum-cleaner at least once a year.

WARNING!

 Keep ventilation openings, in the appliance enclosure or in the built in

structure, clear of obstruction.

 Do not use mechanical devices or other means to accelerate the

defrosting process.

 Do not damage the refrigerant circuit.

EN

13

 Do not use electrical appliances inside the food storage compartments

of the appliance.

Do not place vessels with liquid which could spill on electrical part of

the refrigerator and electrical heating appliances as well (electric stoves, irons, grills

and others that could fire plastic of the mounting plane cover) on the mounting

plane cover.

During the refrigerator maintenance avoid ingress of moisture to the

current carrying parts of the electric equipment.

Protect plastic surfaces of the food storage compartment from any fat, oils,

sauces because they can cause crack of the compartment. In case of unintended spill

immediately clean the surface with dish washing liquid.

While defrosting the refrigerator and cleaning its inside, do not forget

to disconnect it from the mains.

Information:

 leave the doors of refrigerator open, if it is switched off for a long time;

 while selling, transferring or utilising it is obligatory to inform, that in

insulation - cyclopentane (foaming agent C

5

H

10

), refrigerant - R600a

REFRIGERATOR DESIGN

Fig.1

14

1-5

Mounting plane panel with a

set of devices

11 Insert

6 Shelf 12 Cleaner

7 Shelf 14 Condenser

8 Tray 15 Compressor

9 Tray Instruction Manual

10 Tray

Package

Fig.2

Capability to rehang a door for the left-sided opening is provided in the fridge.

In this case there is put the complect of plugs in the polythene bag.

Fig.3

1 - illuminating lamp;

2 - dome light;

3 - temperature controll knob;

4 - temperature controll scale -

(thermoregulator);

5 - green signal lamp -

(electrical system).

15

 remove the bottom cover 10;

 unscrew two screws 7 and remove the bottom bracket 8 together with

the washers 6 on the axle and the spacer 5;

 remove the door 4;

 unscrew the axle 2 together with the nut 1 and the washers 3 from the

upper bracket and screw all this set on the left side of the door;

 displace the plug 14 on the right side;

 hang the door on the axle 2;

 prior to unscrewing the bracket 11 and counterchanging it with the

bottom bracket 8 (together with the set of washers and spacers), insert

the bracket axle into the door;

 the brackets 9 which are under the brackets 11 and 8 remain in their

places;

 put on the bottom cover 10.

PREPARATION FOR USE

Transportation board is of foamed polistyrol. Therefore take out the

adhesive tapes from the sides and simply lift the refrigerator up and take out the

board.

Remove the red transportation holders from the shelves.

Take off two supports 1 from the

sack and insert them into the

guides 2 in the back part of the

table top.

Strip sticky tape off and open

the door. Take out packing

inserted above the doors and

the plastic transportation clips "A"

on lower door bracket later on.

If your appliance is in complement

with glass shelves, pull a shelf in

the direction 1 and remove a red

transportation holder in the

direction 2.

16

In the case of refrigerator relocation lift the front side up so that the

supports were not in contact with the floor.

For self closing of the door adjust the supports so that the refrigerator

stood slightly lifted backward. It is essential to have the supports uniformely

touching the floor.

SELECTION OF THE REFRIGERATOR POSITION

The refrigerator should be placed in a dry well- ventilated room.

The refrigerator must be kept from exposure to direct sun rays. It is not

advisable to locate it near the heat sources (furnace, radiator and so on). If it is

impossible to find out the appropriate place, use an insulating panel.

VENTILATION

ATTENTION! Keep ventilation openings, in the appliance enclosure or in

the built - in structure, clear of obstruction.

If this requirement is not fulfilled, the temperature in the refrigerator rises

and energy consumption in creases.

Warning! Do not cover the top table openings!

CONTROLS AND WARNING LIGHTS

Fig.2

A green illuminating lamp 5 indicates that the refrigerator has been

connected to the mains.

The temperature in the storing chamber is adjusted by the temperature

controll knob.

The temperature controller is switched off, when the knob 3 consides with

a "0" mark in the temperature control scale 4. If the temperature controll knob is turned

clockwise, the temperature in the chamber is reduced.

STORAGE OF THE COOLED FOOD-STUFFS

Fig.1 and Fig.2

The temperature in the storing chamber is a function of the ambient

temperature, position of the temperature controll knob and an amount of the food -

stuffs to be stored.

Initially set the temperature controller knob to "3" position, in case of the

excessive cooling of the foods in the chamber - within limits "1-3" and within "3-5"

range if the cooling is insufficient.

If the thermostat knob is in fifth position and the frost concentrates on

back wall, it is needed to turn the knob to lower position.

17

Liquids and foods having odour or easily taking smell in are to be stored in

closed utensils.

Not foods can be placed into the refrigerating chamber only after

they have been cooled up to a room temperature.

DEFROSTING

Fig.1

The evaporator of the refrigerator is called "crying evaporator". This type

of the evaporator is melting constantly, then the compressor is swithed off

( i.e. if can be covered by frost or dew). The melting water flows to the pan on the top

of compressor.

In order to avoid appearance of odour in the refrigerator, clean it at least

once a month. Wash it with warm water, suds or soda solution.

When cleaning the refrigerator or disconnecting it for any period of

time, perform the following procedures:

 disconnect the refrigerator from the mains;

 take the foods out of the refrigerator;

 leave the door open.

After cleaning, the refrigerator must be wiped and ventilated.

Clean the channel of the trough by means of a long flexible wire of

by means of cleaner 12.

Caution. Do not use mecanical or other devices, wich are not recomended in

user manual, to remove snow and ice.

Note.

Do not clean label with liquids containing alcohol.

Refrigerators produced from a stainles s steel should be cleaned only

with cleansets for those surfaces ("Bio-chem inox-Protect", "Chromol

Edelstahlpfleger").

18

We inform that there are some natural noise resources spread by the

refrigerator which are not failures, as follows:

1. Noise spread by working electric motor of the compressor which is stronger

for a time during start of the compressor.

2. Noise spread by the refrigerant move along tubes which shows itself by

chattering, bubbling, soughing.

If during maintenance troubles occur, make sure

once more it you are able to eliminate them.

Use the troubleshooting chart given below for this purpose.

Information. If refrigerator is out of order and it is not possible to repaire

by means of presented recomendations, switch if off, open the doors and call the

expert.

FAILURE REMOVAL

Trouble Way of remedy

The refrigerator connected

the mains is inoperative (the

green lamp does not light up).

No voltage in the mains or no contact between

the plug and the socket. Check for voltage

presence, check, whether the contact is

available.

An unusual noise arises during

operation of the refrigerator.

The refrigerator is either incorrectly installed or

the tub ing of the refrigerating unit touch the

refrigerator cabinet or a wall.

Check for the refrigerator position according to

the Instruction Manual, eliminate touching.

While opening the door the

gasket gets out.

Insert the gasket into its place strongly pressing

the inner part of the gasket. If the gasket was

poured with oily liquids, it is necessary before

inserting to clean the gasket and the groove in

the door with dish washing agent and wip dry.

When the evaporator is

defrosted, water is collected

in a tray and drains into the

chamber.

The water disposal system is clogged. Clean

the channel of the trough by means of a long

flexible wire of by means of cleaner 12.

19

The refrigerator must be carried in the upright position.

Securely fasten the refrigerator in order to avoid possible shocks while transit.

For better repair service together with your written order or order

by phone you should indicate data of your appliance. You can

find them in the marking label of your appliance – see the fig.

20

Page is loading ...

SAMENSTELLING

1-5 bovenblad met bedieningspaneel 10 leg bak

6 rooster 11 eierhouder

7 glasplaat 13 Instrument de nettoyage

8 groentebak 14

condensor

9 flessenrek

15 compressormotor

VEILIGHEIDSEISEN

Alvorens de koelkast aan te sluiten op het stopcontact dient te worden gecontroleerd of

de aansluitkabel iin goede staat is. Haal altijd de stekker uit het stopcontact bij

ontdooien, schoonmaken of onderhoud van het apparaat. Het zwarte rooster aan de

achterzijde dient ten minste eenmaal per jaar met een zachte stoffer en/of stofzuiger te

worden schoongemaakt.

Bewaar in de kast geen explosieve produkten en flessen met vloeistoffen omdat deze

wellicht uiteen kunnen spatten.

24

Page is loading ...

УСТРОЙСТВО ХОЛОДИЛЬНИКА

1-5

Панель установочной плос-

кости с блоком приборов

11

Вкладыш

6 Полка 12 Скребок

7 Полка 14 Конденсатор

8 Ванночка 15 Компрессор

9 Ванночка Руководство по эсплуатации

10 Ванночка

Упаковка

1 - лампа освещения;

2 - плафон;

3 - ручка терморегулятора;

4 - шкала термлрегулятора-

(терморегулятор);

5 - сигнальная лампа зеленогo

цвета - (сеть).

51

Page is loading ...

EN After Sales Service:

Any maintenance on your equipment should be undertaken by:

- either your dealer,

- or another qualified mechanic who is an authorized agent for the brand

appliances.

When making an appointment, state the full reference of your equipment

(model, type and serial number). This information appears on the

manufacturer's nameplate attached to your equipment.

FR Service après vente :

Les éventuelles interventions sur votre appareil doivent être effectuées :

- soit par votre revendeur,

- soit par un autre professionnel qualifié dépositaire de la marque.

Lors de votre appel, mentionnez la référence complète de votre appareil

(modèle, type et numéro de série). Ces renseignements figurent sur la

plaque signalétique fixée sur votre appareil.

DE Kundendienst :

Eingriffe an Ihrem Gerät dürfen nur:

- von Ihrem Händler oder

- von einem sonstigen Fachmann und Vertragshändler der Marke

durchgeführt werden.

Geben Sie bei der Meldung einer Störung die vollständige

Typenbezeichnung Ihres Gerätes an (Modell, Typ, Seriennummer). Diese

Angaben finden Sie auf einem an Ihrem Gerät angebrachten Schild.

ES Servicio postventa :

Las intervenciones que requiera la máquina deberán ser efectuadas:

- por el revendedor,

- o por cualquier profesional cualificado depositario de la marca.

Al llamar, mencione la referencia completa de la máquina (modelo, tipo y

número de serie). Estos datos figuran en la placa de identificación situada

en la máquina.

PT Serviços autorizados :

Qualquer intervenção no seu aparelho deve ser realizada:

- quer pelo seu revendedor,

- quer por outro profissional qualificado autorizado pela marca.

Ao chamá-los, indique a referência completa do seu aparelho (modelo, tipo

e número de série). Estas informações figuram na placa de identificação

fixada no aparelho.

DA Kundeservice:

Eventuel vedligeholdelse af apparatet skal foretages:

- enten af Deres forhandler,

- eller af en kvalificeret fagmand, som er anerkendt til dette mærke.

Når De ringer op, skal De angive apparatets fulde reference (model, type,

serienummer). Disse oplysninger står på typeskiltet, der sidder på

apparatet.

NL Serviceafdeling:

De eventuele ingrepen in de machine moeten worden uitgevoerd :

- of door uw vakhandelaar,

- of door een andere gekwalificeerd technicus van dit merk.

Tijdens het telefoneren, dient u de complete referentie op te geven van uw

machine (model, type, serienummer). Deze informatie staat op het

typeplaatje op de machine.

PL Usługi serwisowe :

Wszelkie czynności serwisowe wykonywane na urządzeniu muszą być

wykonane przez:

- sprzedawcę,

- wyspecjalizowany zakład naprawczy posiadający atest producenta.

Aby przyspieszyć i ułatwić obsługę prosimy o podanie dokładnych danych

dotyczących urządzenia (model, typ, numer seryjny). Wszystkie te dane

znajdują się na tabliczce znamionowej umieszczonej na urządzeniu.

CS Záruční servis:

Případné opravy na přístroji může provádět pouze :

- váš prodejce

- nebo záruční opravna, která má smlouvu s výrobcem

Při telefonickém styku uvádějte úplné označení vašeho přístroje (model,

typ a výrobní číslo). Tyto údaje jsou uvedeny na výrobním štítku přístroje.

RU Cepвиcнoe oбcлyживaниe:

При необходимости ремонта Вашей машины, он должен

производиться:

- либо тем, кто ее продал Вам;

- либо специалистом, имеющим квалификацию по ремонту данной

модели.

При обращении в службу ремонта укажите все данные Вашей

машины (модель, тип и серийный номер). Эти данные указаны на

идентификационной табличке, закрепленной на устройстве.

EL Tεχνική υποστήριξη:

Οι ενδεχόµενες επεµβάσεις πάνω στη συσκευή σας θα πρέπει να

διενεργούνται:

- είτε από τον προµηθευτή σας,

- είτε από το κατά τόπους εξουσιοδοτηµένο σέρβις.

Σε περίπτωση που τηλεφωνήσετε, θα πρέπει να αναφέρετε όλα τα στοιχεία

της συσκευής σας (µοντέλο, τύπο και αριθµό σειράς).Τα στοιχεία αυτά

αναγράφονται στην ετικέτα των χαρακτηριστικών του κατασκευαστή που

βρίσκεται πάνω στη συσκευή.

Groupe Brandt SL2810 Owner's manual

Related papers

Other documents