Stairmaster HIIT Bike 9-4650 Assembly Instructions

Stairmaster
Brand
Stairmaster
Model
HIIT Bike 9-4650
Type
Assembly Instructions

This manual is also suitable for

HIIT Bike
ASSEMBLY INSTRUCTIONS
For Installation assistance or missing parts, please call CORE Health & Fitness at 1(800) 503-1221Document # 620-8582 Rev. B
PAGE 1 OF 2
STEP 3: Slide the user left side handlebar onto the bike
then use a 6mm allen key to secure the handlebar to the
frame using one (1) piece each of the M8 x 20mm screw
and M8 Belleville washer. Cover with the supplied cap.
Repeat this step for the user right side handlebar.
STEP 2: Use a 5mm allen key to secure the mast to the
frame using three (3) pieces each of the M8 x 16mm
screws and M8 washers. Repeat this step for the other
side of the mast
STEP 1: Connect the RPM sensor lower cable to the upper
cable, slide the beauty ring onto the mast, then slide the mast
down onto the frame of the bike. NOTE: The other connection
port on the adapter cable is only used when using an AC wall
power adapter for the HIIT Console.
.
STEP 4: Finish installing the user left side handlebar
using a 35mm open-ended wrench to secure one (1)
piece of the M24 Axle Nut. Repeat this step for the user
right side handlebar.
STEP 5: Slide the user left foot peg onto the bike, then
secure it using a 13mm socket and two (2) pieces each of
the M8 x 16mm hex head screws and M8 washers.
Repeat this step for the user right side foot peg.
STEP 6: Install the user left side pedal, then using a
14mm socket, torque the pedal bolt to 33-37 Lb-Ft (45-50
Nm). Repeat this step for the user right side pedal.
STEP 7: Slide the seat post sleeve onto the seat post
then loosen and pull the height adjustment pin while
sliding the seat post into the bike frame. Finally secure
the seat post sleeve using a #3 phillips screwdriver to
tighten two (2) pieces of the M4 x 8mm screws.
LR14 1.5V
HIIT Bike
CONSOLE ASSEMBLY INSTRUCTIONS
For Installation assistance or missing parts, please call CORE Health & Fitness at 1(800) 503-1221Document # 620-8582 Rev. B
PAGE 2 OF 2
STEP 4: After installing the console, ensure that the unit type is set
for the appropriate model:
Power the console on by pressing the counter-clockwise arrow.
Press and hold the level up, level down, and clock buttons at the
same time for 3-5 seconds.
Use the down arrow to navigate to the 3rd page and press the clock
button to change between the following:
P1 “tread” - HIITMill and HIITMill X
P2 “bic1” - HIIT Bike
P3 “ergo” - HIIT UBE
P4 "Step" - Not Used Currently
P5 “bic2” - Airfit Bike
P6 none - Not Used Currently
Press the counter-clockwise arrow button to save the unit type.
STEP 3: Use a 3mm allen key to secure the HIIT Console
to the mount using four (4) M5 x 14mm screws.
STEP 2: Before mounting the console to the bike,
gently pull the data cable from the mast then connect
the end of the data cable to the console. NOTE: Be
sure to feed any slack cable back into the mast.
LR14 1.5V
STEP 1: Use a #2 phillips screwdriver to remove the
locking screw securing the battery drawer inside
the console. Remove the battery drawer then
install two (2) LR14 1.5V batteries into the drawer.
Finally, reinsert the battery drawer and reinstall
the locking screw.
  • Page 1 1
  • Page 2 2

Stairmaster HIIT Bike 9-4650 Assembly Instructions

Stairmaster
Brand
Stairmaster
Model
HIIT Bike 9-4650
Type
Assembly Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents