44KRCMK
Ride Command Upgrade Audio Kit
TOOLS NEEDED FOR INSTALLATION
PARTS LIST IMAGES
1. Amp Tray
2. B-H1810 Harness for the 300.4 3. B-H1811 Harness for the 500.1
- Phillips & Flathead Screwdriver
A. On the 300.4 amp, compress the locking tabs and pull the
connectors to disconnect harnesses from the amplier.
A
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against defects in
material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty
against defects in material or workmanship. All Kicker Speakers are covered by a limited 1
year warranty against defects in material or workmanship. All Kicker Ampliers are covered by
a limited 2 year warranty against defects in material or workmanship. Labor for replacement
of defective components is not covered. Contact SSV Works for further warranty information.
300.4
500.1
- Threadlocker (recommended)
44KRCMK
C. On bottom side of the 300.4 amp, remove switch cover, and
set switch levels to match.
G. On the 500.1 amp, compress the locking tabs and pull the
connectors to disconnect harnesses from the amplier.
E. Transfer the 300.4 amp to the Ride Command compatible
amp tray. Fasten the amp to the tray with your existing M4
hardware. We recommend applying Threadlocker.
D. Remove gain control plugs, starting from zero adjust gain
control clock wise to the position shown. Once tuned re-insert
plugs and switch cover.
F. Connect harness B-H1810 to the 300.4. The 8-pin connector to the input
side of the amp and 10-pin connector to the output side of the amp.
C
G
ED
F
B. With the amplier disconnected, unscrew the (4) screws that
secure the amp to the amp tray.
B
H. With the amplier disconnected, unscrew the (4) screws that
secure the amp to the amp tray.
H
44KRCMK
I. On bottom side of the 500.1 amp, remove switch cover, and
set switch levels to match.
K. Transfer the 500.1 amp to the Ride Command compatible
amp tray. Fasten the amp to the tray with your existing M4
hardware. We recommend applying Threadlocker.
NOTE: the power/ ground, and speaker outputs of both amps
face toward the white SSV logo on the tray.
J. Remove gain control plug, starting from zero adjust gain control
clock wise to the position shown. Once tuned re-insert plugs
and switch cover.
L. Connect harness B-H1811 to 500.1. The 4-pin connector to the input side of
the amp and 6-pin connector to the output side of the amp.
Follow standard kit instruction for installation of the Ride Command
compatible amp tray
I
KJ
L
© 2019 SSV Works, Oxnard, CA 93030 44KRCMK Rev. A 5-22-19
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
SSV Works PHASE 5 X3-F4 User manual
-
Kicker 45CX33 Owner's manual
-
-
-
-
-
-
-
-
Other documents
-
SSV Works RZR XP1000 Installation guide
-
SSV Works BR-2B65U User guide
-
-
SSV Works YZ-FKP65 User manual
-
SSV Works WP-RZF3O4 Installation guide
-
SSV Works BR-B65 User manual
-
Audio System X-500.1 MD Owner's manual
-
SSV Works MT-F65A User manual
-
UTICA BOILERS SSC Warranty
-
SSV Works US-10U User manual
