Rittal RIMATRIX5 PMC12 User manual

Brand: Rittal

Model: RIMATRIX5 PMC12

Type: User manual

Rittal PMC12

DC - Manual

(Relay Card)

FRIEDHELM LOH GROUP

R i t t a l GmbH & Co. KG

Auf dem Stützel

berg

D – 3 5 7 4 5 H e r b o r n

Deutschland

Germany

Email: [email protected]

http://www.rittal.com

Service -Tel. : (+49) - (0)2772 / 505 - 0

Service - Fax : (+49) - (0)2772 / 505 - 2319

A 38333 07 IT 74e

Manual Dry Contact Card PMC12

Microsoft Windows is a registered trademark of Microsoft Corporation.

Acrobat Reader is a registered trademark of Adobe Systems Incorporated.

Manual Dry Contact Card PMC12

Table of Contents

1. Safety Instructions 4

1.1. D

OCUMENTATION

OTES

1.2. R

ETENTION OF THE

OCUMENTS

1.3. U

SED

YMBOLS

1.4. S

AFETY

NSTRUCTIONS

1.5. P

ROPER

2. Product Introduction 5

3. Functional Descriptions 5

3.1.

PIN ASSIGNMENTS OF THE

10-P

TERMINAL

(CN3): 5

3.2. J

UMPER SETTINGS AND

INSTALLATION

Manual Dry Contact Card PMC12

1 Safety Instructions

1.1. Documentation Notes

The audience for this guide is the technical

specialist familiar with the assembly, installation

and operation of the PMC12 UPS-System.

You should read this operating guide prior to

commissioning and store the guide so it is

readily accessible for subsequent use.

Rittal cannot accept any liability for damage

and operational malfunctions that result from

the non observance of this guide.

1.2. Retention of the Documents

This guide and all associated documents are

part of the product. They must be given to the

operator of the unit and must be stored so they

are available when needed.

1.3. Used Symbols

The following safety and other notes are used

in this guide:

Symbol for handling instructions:

• This bullet point indicates that you should

perform an action.

Safety and other notes:

Danger!

Immediate danger to health and

life!

Warning!

Possible danger for the product

and the environment!

Note!

Useful information and special

features.

1.4. Safety Instructions

1. Assembly and installation of the UPS, in

particular for wiring the enclosures with

mains power, may be performed only by a

trained electrician. Other tasks associated

with the UPS, such as the assembly and

installation of system components with

tested standard connectors, and the

operation and configuration of the PMC12

UPS-System may be performed only by

instructed personnel.

2. Observe the valid regulations for the

electrical installation for the country in which

the unit is installed and operated, and the

national regulations for accident prevention.

Also observe any company-internal

regulations (work, operating and safety

regulations).

3. Do not try to repair the unit yourself; contact

your local supplier or your warranty will be

void.

4. Do not install the Unit in an environment with

sparks, smoke or gas.

5. Use only genuine or recommended parts

and accessories. The use of other parts can

void the liability for any resulting

consequences.

1.5. Proper

Use

This relay card is designed for communicate

with Rittal UPS-Systems. A use different from

that described here is considered to be an

improper use. Rittal cannot accept any liability

for damage resulting from the improper use or

the non-observance of this guide. The guides

for the used accessories may apply.

Rittal prohibits the use for life-preserving appli-

cations (such as the use in hospitals or the di-

rect patient care). Rittal expressly does not sell

its products for such applications. Rittal will not

accept any responsibility if a UPS is used in

this area.

Manual Dry Contact Card PMC12

2 Product Introduction

Relay card for installation in Rittal PMC12

single phase ups-system. The card can be

used at article numbers DK7857.430,

DK7857.431, DK7857.432, DK7857.433 and

DK7857.434.

At the article numbers DK7857.433 and

DK7857.434 the card can be installed in slot 1

or 2.

3 Functional Descriptions

The card will transmit the ups messages via

potential free contacts. The available messages

are:

• UPS on Bypass mode.

• Utility Normal (Normal close or open

contact)

• Inverter On

• Battery Low

• Battery Bad or Abnormal

• UPS Alarm

• Shutdown UPS

3.1. The pin assignments of the 10-Pin

terminal (CN3):

1 2 3 4 5 6 7 8 9

Pin 1: UPS on Bypass mode.

Pin 2: Utility Normal (Normal close contact)

Pin 3: Utility Normal (Normal open contact)

Pin 4: Inverter On

Pin 5: Battery Low

Pin 6: Battery Bad or Abnormal

Pin 7: UPS Alarm

Pin 8: Common

Pin 9: Shutdown UPS positive (+ ) signal

Pin 10: Shutdown UPS negative (- ) signal

3.2.

Jumper settings and installation

• The shutdown function will be activated,

after a +6~+25Vdc is put between pin9 and

pin10 for 5 seconds.

• Installation Position: slot1(DK7857.430 –

434) or slot 2 (DK7857.433 and 7857.434)

• Flexible signal output for N.C.(Normal

close) or N.O.(Normal open) contact by

shorting pin1-2 or pin2-3 from JP1-5.

• The shutdown function will be enabled in 1

minute after blackout occurs if the pin1-2 of

both CN1 and CN6 be shorted by cap. Or,

the shutdown function can only be enabled

by pin9-10 of CN3 if the pin2-3 of both CN1

and CN6 be shorted by cap.

CN1

JP4

JP5

CN6

JP1

CN3

Rittal RIMATRIX5 PMC12 User manual

Rittal RIMATRIX5 PMC12 User manual

Rittal RIMATRIX5 PMC12 User manual

Related papers

Other documents