Korg Slimpitch SLM-1CM-PG Owner's manual

Category
Microphones
Type
Owner's manual

This manual is also suitable for

Precautions
Location
Using the unit in the following locations can result in a malfunction.
• In direct sunlight
• Locations of extreme temperature or humidity
• Excessively dusty or dirty locations
• Locations of excessive vibration
• Close to magnetic elds
Power supply
Be sure to turn the power switch to OFF when the unit is not in use. Remove the battery
in order to prevent it from leaking when the unit is not in use for extended periods.
Interference with other electrical devices
Radios and televisions placed nearby may experience reception interference. Operate
this unit at a suitable distance from radios and televisions.
Handling
To avoid breakage, do not apply excessive force to the switches or controls.
Care
If the exterior becomes dirty, wipe it with a clean, dry cloth. Do not use liquid cleaners
such as benzene or thinner, or cleaning compounds or ammable polishes.
Keep this manual
After reading this manual, please keep it for later reference.
Keeping foreign matter out of your equipment
Never set any container with liquid in it near this equipment. If liquid gets into the
equipment, it could cause a breakdown, re, or electrical shock. Be careful not to let
metal objects get into the equipment.
THE FCC REGULATION WARNING (for USA)
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
If items such as cables are included with this equipment, you must use those
included items.
Unauthorized changes or modication to this system can void the user’s authority
to operate this equipment.
Notice regarding disposal (EU only)
When this “crossed-out wheeled bin” symbol is displayed on the product,
owner’s manual, battery, or battery package, it signies that when you
wish to dispose of this product, manual, package or battery you must do
so in an approved manner. Do not discard this product, manual, package
or battery along with ordinary household waste. Disposing in the correct
manner will prevent harm to human health and potential damage to the
environment. Since the correct method of disposal will depend on the
applicable laws and regulations in your locality, please contact your local
administrative body for details. If the battery contains heavy metals in
excess of the regulated amount, a chemical symbol is displayed below the
“crossed-out wheeled bin” symbol on the battery or battery package.
IMPORTANT NOTICE TO CONSUMERS
This product has been manufactured according to strict specications and volt-
age requirements that are applicable in the country in which it is intended that
this product should be used. If you have purchased this product via the internet,
through mail order, and/or via a telephone sale, you must verify that this product
is intended to be used in the country in which you reside.
WARNING: Use of this product in any country other than that for which it is
intended could be dangerous and could invalidate the manufacturer’s or dis-
tributor’s warranty.
Please also retain your receipt as proof of purchase otherwise your product may
be disqualied from the manufacturer’s or distributor’s warranty.
CALIFORNIA USA ONLY
This Perchlorate warning applies only to primary CR (Manganese Dioxide) Lithium
coin cells sold or distributed ONLY in California USA.
Perchlorate Materialspecial handling may apply, See www.dtsc.ca.gov/haz-
ardouswaste/perchlorate.”
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAN ICES-3 B / NMB-3 B.
Thank you for purchasing the Korg Slimpitch Chromatic
Tuner.
Merci d’avoir choisi lAccordeur Chromatique Slimpitch
de Korg.
Vielen Dank, dass Sie sich für das chromatische Stimmge-
t Slimpitch von Korg entschieden haben.
Gracias por comprar el anador cromático Slimpitch de Korg.
Donotapplyexcessiveforcetothebaseofthecontactmicrophone.Otherwise,it
couldbedisconnected.
Backlight
The backlight will illuminate brightly when sound is input or when a buon
is pressed.
When there has been no user input for approximately three seconds on the
tuner, the backlight will dim slightly in order to prevent the baery from be-
ing depleted.
Tuning
To tune your instrument by using the dedicated contact microphone supplied,
connect it to the INPUT jack on the Slimpitch.
When nothing is connected to the INPUT jack, tuning is performed using the
built-in microphone.
Tuning procedure
1. Pressthepowerbuon.Thepowerwillturnon/oeachtimeyoupress
thisbuon.
If the power is le on for approximately 20 minutes without any user input,
it will turn o automatically.
2. Ifnecessary,changethecalibrationandtransposeseingsaccordingto
yourneeds.
3. Playasinglenoteonyourinstrument.
The display will show the name of the note thats closest to the pitch de-
tected. Tune your instrument to the correct pitch so that the desired note
name appears.
4. Onceagain,playasinglenoteonyourin-
strumentandadjustthetuningsothatthe
centersegmentofthemeter(indicatedby
)
islitup.
An indicator toward the right will light up if
the pitch is too high, and an indicator toward
the le will light up if the pitch is too low.
If you want to tune to a pure major third or pure minor third above a certain
note, adjust the pitch to the pure major or minor third marks on the meter.
For example if you want to tune to a pure major third above A, make the
note name indicator read C
#
, and tune so that the meter indicates the le [ ].
Alternatively, if you want to tune to a pure minor third above A, make the
note name indicator read C, and tune so that the meter indicates the right [
].
Evenifthepitchiswithintherangeofdetection,itmaynotbepossibletodetectthe
pitchofaninstrumentalsoundthatcontainslargenumbersofovertonesorasound
thathasarapiddecay.
Themetermayrespondtovibrationsitpicksupfromtheenvironment;however,
thiswillnotaecttuningoftheinstrument.
Calibration (reference pitch) settings (*M)
Press the CALIB [ ] or [ ] buon to change the seing within the range of 410
Hz to 480 Hz in 1 Hz steps. Hold down the buon to increase or decrease the
seing continuously
Transpose (*M)
This function is for tuning a transposing instrument. Each time you press the
TRANS buon, the seing will cycle between F B
b
E
b
C (no transposi-
tion; the TRANSPOSE indicator will not appear) F...
Specications
Scale: 12-note equal temperament
Range(sinewave): A0 (27.50 Hz)–C8 (4186 Hz)
Precision: +/-1 cent
Referencepitch: A4 = 410–480 Hz (1 Hz steps)
Transpositionrange: C, F, B
b
, E
b
Dimensions: 75 mm (W) X 32 mm (D) X 15 mm (H)/
2.95 inches (W) X 1.26 inches (D) X 0.59 inches (H)
Weight: 28 g/0.99 oz. (including baery)
Baerylife Approximately 8 hours
(A4 input, operating continuously)
Includeditems: Dedicated contact microphone, metal plate,
CR2032 lithium baery (3 V)
*M Seings are remembered even when the power is o. However, seings
will be initialized when you replace the baery (default, calibration: 442
Hz, no transposition (C)).
• Specications and appearance are subject to change without notice for im-
provement.
Meter indications
when correctly tuned
Parts of the Slimpitch
Installing the battery
Makesuretoturnthepowerobeforeyouinstallorreplacethebaery.
When the baery starts to run low, the baery indicator (
) is displayed.
The Slimpitch will continue to function for a while longer, but tuning will
become less accurate. Replace the baery as soon as possible.
1. SlidethebaerycoveronthebackoftheSlimpitchinthedirectionindi-
catedbyarrowA,andthenliitup.
2. Makingsuretoobservethecorrectpolarity,insertthebaerysothatthe
“+”sideofthebaeryisvisible.
3. Returnthebaerycovertoitsoriginalposition.
Using the Slimpitch
You can use the clear cover on the Slimpitch as a stand by rotating it as shown
here.
There is also a magnet built-into the Slimpitch. This allows you to aach
it to the lower part of a metal a music stand etc.
ToaachtheSlimpitchtomusicstandsthatarenotmagnetic(aluminum,plastic,
etc.),youneedtoaachthemetalplatesupplied.
DonotplaceorstorethemagneticsectionoftheSlimpitchnearitemssuchaswatches,
harddrives,magneticcardsoranyotheritemthatcanbeaectedbymagneticelds.
Using the dedicated contact microphone
By connecting the dedicated contact microphone to the INPUT jack and aach-
ing the clip to your instrument, you can eliminate the inuence of surrounding
noises when tuning your instrument.
Pleasecarefullyaachthecontactmicrophonetoyourinstrument.Leavingthe
Slimpitchaachedforalongperiodoftimemaydamageormarktheinstrument’s
surface.
Dependingonvariousfactorssuchasage-relatedchangeorthesurfacenish,there
isapossibilitythatyourinstrumentmaybedamagedbyaachingthisproduct.
Reference pitch
indicator
Battery icon
Note name indicator
Pure major third
Pure minor third
CALIB button
CALIB button
TRANSPOSE
setting indicators
Power button
TRANS button
INPUT jack
Internal mic
Clear cover
Magnetic section
Partes del Slimpitch
Instalación de la Batea
Apaguelaunidadantesdeinstalaroreemplazarlabatería.
Cuando la batería comience a agotarse, se mostrará el indicador de batería (
).
El Slimpitch seguirá funcionando un tiempo, pero la anacn se menos
precisa. Reemplace la batea tan pronto como sea posible.
1. DeslicelatapadelabateríasituadaenlaparteposteriordelSlimpitchen
ladireccnqueindicalaechaAy,acontinuacn,lentela.
2. Insertelabateríaasegundosedequelapolaridadescorrecta,deforma
quelacara“+”delabateríaseavisible.
3. Vuelvaacolocarlacubiertadelabateríaensuposiciónoriginal.
Uso del Slimpitch
Puede utilizar la cubierta transparente del Slimpitch como un soporte girándola
como se muestra aquí.
También hay un in integrado en el Slimpitch. Le permite jarlo a la
parte inferior de un atril musical melico, etc.
ParajarelSlimpitchalosatrilesmusicalesquenosonmagnéticos(aluminio,
plástico,etc.),debecolocarlaplacametálicasuministrada.
NocoloqueniguardelasecciónmagnéticadelSlimpitchcercadeobjetoscomorelojes,
discosduros,tarjetasmagticasocualquierotroobjetoquepuedaverseafectado
porcamposmagticos.
Uso del micrófono de contacto dedicado
Si conecta el micrófono de contacto dedicado a la toma INPUT y ja el clip al
instrumento, puede eliminar la inuencia de los ruidos ambientales al anar
el instrumento.
Feconcuidadoelmicrófonodecontactoasuinstrumento.SidejaelSlimpitchsujeto
alinstrumentoduranteunlargoperiodo,puededañarlasuperciedelinstrumento.
Dependiendodevariosfactores,comoelenvejecimientodelacabadodelasupercie,
existelaposibilidaddequesuinstrumentopuedadañarseporlacolocacndel
anador.
Indicador de tono
de referencia
Indicador de nombre de nota
Botón TRANS
Icono de batería
Tercera mayor pura
Tercera menor pura
Botón CALIB
Botón CALIB
Indicadores
de ajuste de
TRANSPOSE
Botón de
alimentación
Toma INPUT
Micrófono
interno
Cubierta
transparente
Sección magnética
Flauta
Clarinete
Saxofón
Noejerzaunafuerzaexcesivasobrelabasedelmicrófonodecontacto.Delocontrario,
podríadesconectarse.
Retroiluminación
La retroiluminación se hace más brillante cuando hay sonido de entrada o
cuando se pulsa un botón.
Si el usuario no realiza ninguna operación durante unos tres segundos, la
retroiluminación se atenuará ligeramente para evitar que la batea se agote.
Anación
Para anar el instrumento utilizando el micrófono de contacto dedicado sumi-
nistrado, coctelo a la toma INPUT del Slimpitch.
Si no se conecta ningún componente a la toma INPUT, la anación se realiza
con el micrófono integrado.
Procedimiento de anacn
1. Pulseelbotóndealimentación.Launidadseenciendeoseapagacadavez
quepulseestebon.
Si la alimentación se deja encendida durante unos 20 minutos sin ningún
sonido de entrada, seapagará de forma automática.
2. Encasonecesario,cambielosajustesdecalibraciónytransposicnsegún
susnecesidades.
3. Toqueunasolanotaensuinstrumento.
La pantalla mostrael nombre de la nota s cercana al tono detectado.
Ane su instrumento con el tono correcto para que aparezca el nombre de la
nota deseada.
4.
De nuevo, toque una nota en su instru-
mentoyajustelaanacióndeformaquese
ilumine el segmentocentral delmedidor
(indicadopor
).
El indicador de la derecha se iluminasi el
tono es demasiado agudo, y el indicador de la
izquierda se iluminasi es demasiado grave.
Si desea anar una tercera mayor pura o una
tercera menor pura por encima de una cierta nota, ajuste el tono hasta que
la tercera mayor o menor pura se marque en el medidor.
Por ejemplo, si desea anar una tercera mayor pura por encima de A, haga que
el indicador de nombre de nota marque C
#
y ane de forma que el medidor
indique la izquierda [
]. Asimismo, si desea anar una tercera menor pura
por encima de A, haga que el indicador de nombre de nota marque C y ane
de forma que el medidor indique la derecha [
].
Aunqueeltonoestédentrodelrangodedetección,puedequenoseaposibledetectarel
tonodeunsonidoquecontengagrancantidaddearmónicosoquetengaunarápidacaída.
Elmedidorpuederesponderalasvibracionesquerecogedelentorno;sinembargo,
esonoafectaráalaanacióndelinstrumento.
Ajustes de la calibracn (tono de referencia) (*M)
Pulse el botón CALIB [ ] o [ ] para cambiar el ajuste en el intervalo de 410 Hz
a 480 Hz en pasos de 1 Hz. Mantenga pulsado el botón para aumentar o reducir
el ajuste de forma continua.
Transposición (*M)
Esta función se utiliza para anar un instrumento de transposición. Cada vez
que pulse el botón TRANS, el ajuste cambiará entre F B
b
E
b
C (sin trans-
posición; el indicador TRANSPOSE no aparecerá) F...
Especicaciones
Escala: 12 notas, temperamento igual
Rango(ondasinusoidal): A0 (27,50 Hz)C8 (4186 Hz)
Precisión: +/-1 centésima
TonodeReferencia: A4 = 410–480 Hz (en pasos de 1 Hz)
Rangodetransposición: C, F, B
b
, E
b
Dimensiones: 75 mm (Anch.) x 32 mm (Prof.) x 15 mm (Alt.)
Peso: 28 g (incluyendo batea)
Vidaútildelabatería: Aproximadamente 8 horas
(entrada A4, funcionando continuamente)
Elementosincluidos: Micrófono de contacto dedicado, placa melica,
batería de litio CR2032 (3 V)
*M
Los ajustes se recuerdan incluso al apagar la unidad. No obstante, los ajustes
se inicializan al reemplazar la batería (valor por defecto, calibración: 442
Hz sin transposición (C)).
• Las especicaciones y el aspecto están sujetos a cambios sin previo aviso por
mejora.
Indicaciones de
medidor si se ha
afinado correctamente
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Korg Slimpitch SLM-1CM-PG Owner's manual

Category
Microphones
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI