Hoover DXA 175AH/1-AUS User manual

EN

DXA 175AH/1-AUS

!

2

Thank-you for choosing a Hoover washing

machine. We are proud to always offer

new, innovative and technologically

advanced products, with a complete range

of home appliances to ensure true

assistance in your daily routine.

Carefully read this manual for correct and

safe appliance use and for helpful tips on

efficient maintenance.

Only use the washing machine

after carefully reading these instructions.

We recommend you always keep this

manual on hand and in good conditions for

any future owners.

Please check that the appliance is

delivered with this instruction manual,

warranty certificate, water and energy

efficiency label. Also check that plugs,

curve for drain hose and liquid detergent or

bleach tray (only on some models) are

included. We recommend you keep all

these components.

Each product is identified by a unique 16-

character code, also called the “serial

number”, printed on the sticker affixed to

the appliance (porthole area) or in the

document envelope found inside the

product.

This appliance is marked according to

the European directive 2012/19/EU

on Waste Electrical and Electronic

Equipment (WEEE).

WEEE contains both polluting substances (which

can cause negative consequences for the

environment) and basic components (which can

be re-used). It is important to have WEEE

subjected to specific treatments, in order to

remove and dispose properly all pollutants, and

recover and recycle all materials. Individuals can

play an important role in ensuring that WEEE

does not become an environmental issue; it is

essential to follow some basic rules:

! WEEE should not be treated as household

waste;

! WEEE should be handed over to the relevant

collection points managed by the municipality or

by registered companies. In many countries, for

large WEEE, home collection could be present.

In many countries, when you buy a new

appliance, the old one may be returned to the

retailer who has to collect it free of charge on a

one-to-one basis, as long as the equipment is of

equivalent type and has the same functions as

the supplied equipment.

1. GENERAL SAFETY RULES

2. INSTALLATION

3. PRACTICAL TIPS

4. MAINTENANCE AND CLEANING

5. QUICK USER GUIDE

6. CONTROLS AND PROGRAMS

7. CUSTOMER SERVICE CENTRE AND

WARRANTY

Environmental conditions

Contents

!

EN

3

1. GENERAL SAFETY

RULES

! This appliances is intended to

be used in household and

similar applications such as:

- Staff kitchen areas in shops, offices

and other working environments;

- Farm houses;

- By clients in hotels, motels and

other residential type environments;

- Bed and breakfast type environments.

A different use of this appliance

from household environment

or from typical housekeeping

functions, as commercial use by

expert or trained users, is excluded

even in the above applications. If

the appliance is used in a manner

inconsistent with this it may reduce

the life of the appliance and may

void the manufacturer’s warranty.

Any damage to the appliance or

other damage or loss arising

through use that is not consistent

with domestic or household use

(even if located in a domestic or

household environment) shall not

be accepted by the manufacturer to

the fullest extent permitted by law.

!

This appliance is not intended

for use by persons (including

children) with reduced physical,

sensory or mental capabilities,

or lack of experience and

knowledge, unless they have

been given supervision or

instruction concerning use of

the appliance by a person

responsible for their safety.

Children shall not play with the

appliance. Cleaning and user

maintenance shall not be made

by children without supervision.

! Children should be supervised

to ensure that they do not play

with the appliance.

! Children of less than 3 years

should be kept away unless

continuously supervised.

! If the supply cord is damaged, it

must be replaced by the

manufacturer, its service agent

or similarly qualified persons in

order to avoid a hazard.

! Only use the hose-sets

supplied with the appliance for

the water supply connection

(do not reuse old hose-sets).

! Water pressure must be between

0,05 MPa and 0,8 MPa.

! Make sure that carpet does not

obstruct the base of the machine

and ventilation openings.

! The OFF condition is reached

by

placing the reference mark on

the programmes control/knob in

the vertical position. Any other

different position of such control

sets the machine in ON condition

(only for models with programmes

knob).

!

4

! After installation, the appliance

must be positioned so that the

plug is accessible.

! The maximum load capacity of

dry clothes is 7,5 kg.

! Before cleaning or maintaining

the washing machine, unplug

the appliance and turn off the

water faucet.

! Make sure the electrical system

is grounded. Otherwise, seek

qualified professional assistance.

! Please do not use converters,

multiple sockets or extension

cords.

! Make sure there is no water in

the drum before opening the

porthole.

! Do not pull on the power cord

or appliance to unplug the

machine.

! Do not expose the washing

machine to rain, direct sunlight

or other weather elements.

! When moving, do not lift the

washing machine by the knobs

or detergent drawer; during

transport, never rest the

porthole on the trolley. We

recommend two people lift the

washing machine.

! In the event of fault and/or

malfunction, turn off the

washing machine, close the

water faucet and do not tamper

with the appliance.

Immediately contact the

Customer Service Centre and

only use original spare parts.

Failure to observe these

instruction may jeopardise

appliance safety.

Appliance complies with

European Directives:

! 2006/95/EC (LVD);

! 2004/108/EC (EMC);

! 2009/125/EC (ErP);

! 2011/65/EU (RoHS)

and subsequent amendments.

Safety instructions

WARNING:

water may reach very high

temperatures during the

wash cycle.

!

EN

5

2. INSTALLATION

! Cut the hose straps, being

careful not to damage the hose

and power cord.

! Unscrew the 2 or 4 screws (A)

on the back and remove the 2

or 4 washers (B) as illustrated

in figure 1.

! Close the 2 or 4 holes using

the plugs included in the

instruction envelope.

! If the washing machine is built-in,

after cutting the hose straps,

unscrew the 3 or 4 screws (A) and

remove the 3 or 4

washers

(B).

! In some models, 1 or more

washers

will fall inside the

machine: tilt the washing machine

forward to remove them. Close

the holes using the plugs found in

the envelope.

! Place the polionda sheet on

the bottom as shown in figure

2 (according to the model,

consider version A, B or C).

A

B

1

3

2

1

3

1

2

A

C

B

2

WARNING:

keep packaging materials

away from children.

!

6

! Connect the water tube to the faucet, only

using the drain tube supplied with the

washing machine (fig. 3).

DO NOT OPEN THE FAUCET.

! Some models may include one or more of

the following features:

! HOT&COLD (fig. 4):

water mains connection settings with hot

and cold water for higher energy savings.

Connect the grey tube to the cold water

faucet and the red one to the hot water

faucet. The machine can be connected to

the cold water faucet only: in this case,

some programs may start a few minutes

later.

! AQUASTOP (fig. 5):

a device located on the supply tube that

stops water flow if the tube deteriorates;

in this case, a red mark will appear in the

window “A” and the tube must be

replaced. To unscrew the nut, press the

one-way lock device "B".

! AQUAPROTECT – SUPPLY TUBE WITH

GUARD (fig. 6):

Should water leak from the primary

internal tube "A", the transparent

containment sheath "B" will contain water

to permit the washing cycle to complete.

At the end of the cycle, contact the

Customer Service Centre to replace the

supply tube.

! Position the washing machine near to the

wall, being careful that the hose is not

bent or crushed, and place the drain hose

in the tub or, preferably, connect it to a

wall drain at least 50 cm high with

diameter greater than the washing

machine hose (fig. 7).

3

1

4

B

A

5

B

A

6

min 50 cm

max 85 cm

+2,6 mt

max

max 100 cm

min 4 cm

7

Hydraulic connections

Setting

!

EN

7

! Level the appliance using the feet as

illustrated in figure 8:

a. turn the nut clockwise to release the

screw;

b. rotate the foot to raise or lower it until it

adheres to the floor;

c. lock the foot, screwing in the nut, until it

adheres to the bottom of the washing

machine.

! Plug in the appliance.

A

B

C

8

The detergent draw is split into 3

compartments as illustrated in figure 9:

! compartment "1": for prewash detergent;

! compartment “ ”: for special additives,

softeners, starch fragrances, etc.;

! compartment "2": for washing detergent.

A liquid detergent cup is also included in

some models (fig. 10). To use it, place it in

compartment "2". This way, liquid detergent

will only enter the drum at the right time. The

cup can also be used for bleach when the

“Rinse” program is selected.

9

1

2

10

1

2

WARNING:

contact the Customer Service Centre

should the power cord need replacement.

Detergent drawer

WARNING:

only use liquid products; the washing

machine is set to automatically dose

additives at each cycle during the last

rinse.

WARNING:

Some liquid detergents are hard to

dissolve. In this case we recommend

diluting the detergent with warm water.

We recommend you use only 20% of

the recommended detergent quantities

shown on the detergent pack.

!

8

3. PRACTICAL TIPS

WARNING: when sorting laundry, make

sure:

- have eliminated metallic objects such as

barrettes, pins, coins, from laundry;

- to have buttoned pillow cases, closed

zips, tied loose belts and long robe

ribbons;

- to have removed rollers from curtains;

- to have carefully read clothing washing

labels;

- to have removed any persistent stains

using specific detergents.

! When washing rugs, bedcovers or other

heavy clothing, we recommend you avoid

spinning.

! To wash wool, make sure the item can be

machine washed and marked by the

“Pure virgin wool” symbol with the “Does

not mat” or “Machine washable” label.

A guide environmentally friendly and

economic use of your appliance.

Maximise The Load Size

! Achieve the best use of energy, water,

detergent and time by using the

recommended maximum load size.

Save up to 50% energy by washing a full

load instead of 2 half loads.

Do you need to pre-wash?

! For heavily soiled laundry only!

SAVE detergent, time, water and

between 5 to 15% energy consumption

by NOT selecting Prewash for slight to

normally soiled laundry.

Is a hot wash required?

! Pretreat stains with stain remover or soak

dried in stains in water before washing to

reduce the necessity of a hot wash

programme.

Save up to 50% energy by using a 60°C

wash programme.

Following is a quick guide with tips and

recommendations on detergent use at the

various temperatures. In any case, always

read the instructions on the detergent for

correct use and doses.

Load tips

Helpful suggestions for the user

When washing heavily soiled whites,

we recommend using cotton

programs of 60°C or above and a

normal washing powder (heavy duty)

that contains bleaching agents that at

medium/high temperatures provide

excellent results.

For washes between 40°C and 60°C

the type of detergent used needs to be

appropriate for the type of fabric and

level of soiling.

Normal powders are suitable for “white”

or colour fast fabrics with high soiling,

while liquid detergents or “colour

protecting” powders are suitable for

coloured fabrics with light levels of

soiling.

For washing at temperatures below

40°C we recommend the use of liquid

detergents or detergents specifically

labeled as suitable for low temperature

washing.

Please note - dilute viscous liquid

detergent with warm water if necessary.

For washing wool or silk, only use

detergents specifically formulated for

these fabrics.

!

EN

9

4. MAINTENANCE AND

CLEANING

To clean the washing machine exterior, use

a damp cloth, avoiding abrasives, alcohol

and/or solvents. The washing machine does

not require any special care for ordinary

cleaning: clean drawer compartments and

the filter; some tips on how to move the

machine or on long periods of disuse are

provided below.

! We recommend you clean the drawer to

avoid accumulating detergent and

additive residue.

! To do this, extract the drawer using slight

force, clean it with running water and

reinsert it in its housing.

! The washing machine comes with a

special filter able to trap large residue,

such as buttons or coins, which could

clog the drain.

! Only available on certain models: pull out

the corrugated hose, remove the stopper

and drain the water into a container.

! Before unscrewing the filter, we

recommend you place an absorbent cloth

under it to keep the floor dry.

! Turn the filter counter-clockwise to the

limit stop in the vertical position.

! Remove and clean the filter; when

finished, replace it turning it clockwise.

! Repeat the previous steps in reverse

order to reassemble all parts.

! Should the washing machine be stored in

an unheated room for a long period of

time, drain all water from tubes.

! Unplug the washing machine.

! Detach the hose from the strap and lower

it, fully draining water into a bowl.

! Secure the drain hose with the strap

when finished.

Drawer cleaning

Filter cleaning

Suggestions for moves or

prolonged disuse

!

10

5. QUICK USER GUIDE

This washing machine automatically adapts

the level of the water to the type and

quantity of washing. This system gives a

decrease in energy consumption and a

sensible reduction in washing times.

! Turn on the washing machine and select

the required program.

! Adjust the washing temperature if

necessary and press the required "option"

buttons.

! Press the START/PAUSE button to start

washing.

Should power go out when the washing

machine is running, a special memory

saves the settings and, when power

returns, the machine resumes the cycle

from where it left off.

! The message "end" will appear on the

display or the corresponding led will turn

on at the end of the program.

! Turn off the washing machine.

For any type of wash, see the program

table and follow the operating sequence

as indicated.

Water pressure:

min 0,05 Mpa

max 0,8 Mpa

Spin r.p.m.:

See rating plate.

Power input / Power current fuse amp /

Supply voltage:

See rating plate.

6. CONTROLS AND

PROGRAMS

B

DCEFGHI

M

L

A

Programme selector with OFF

position

B

START/PAUSE button

C

SPIN SPEED button

D

TEMPERATURE SELECTION

button

E

DELAY START button

F

WASH TIME button

G

EXTRA RINSE button

H

OPTIONS button

I

EASY IRON button

L

Digital display

M

DOOR LOCKED indicator light

Program selection

Wait until the porthole locked light

turns off: about 2 minutes after the

program ends.

Technical data

!

EN

11

! Press the START/PAUSE button to start

the selected cycle.

! Once a programme is selected the

programme selector remains stationary on

the selected programme till cycle ends.

! Switch off the washing machine by

turning the selector to OFF.

! Press to start the selected cycle.

ADD OR REMOVE ITEMS AFTER THE

PROGRAMMES HAS STARTED (PAUSE)

! Press and hold the START/PAUSE

button for about 2 seconds (some

indicator light and the time remaining

indicator will flash, showing that the

machine has been paused).

! Wait 2 minutes until the safety device

unlocks the door.

! After you have added or removed items,

close the door and press the

START/PAUSE button (the programme

will start from where it left off).

CANCELLING THE PROGRAMME

! To cancel the programme, set the

selector to the OFF position.

WARNING:

Don’t touch the display while inserting

the plug because the machines

calibrates the systems during the first

seconds: touching the display, the

machine couldn’t work property. In

this case, remove the plug and repeat

the operation.

Opening the door

A special safety device prevents the

door from being opened immediately

after the end of the cycle.

Wait for 2 minutes after the wash

cycle has finished and the "Door

Security" light has gone out before

opening the door.

PROGRAMME selector with OFF

position

When the programme selector is turned

the display lights up to show the settings

for the programme selected.

For energy saving, at the end of the

cycle or with an inactivity period, the

display level contrast will decrease.

N.B.: To switch the machine off, turn the

programme selector to the OFF

position.

The programme selector must be

returned to the OFF position at the end

of each cycle or when starting a

subsequent wash cycle prior to the next

programme being selected and started.

START/PAUSE button

Close the door BEFORE selecting the

button START/PAUSE.

When the START/PAUSE button has

been pressed, the appliance can take

few seconds before it starts working.

!

12

! By pressing this button, it is possible to

reduce the maximum speed, and if you

wish, the spin cycle can be cancelled.

! To reactivate the spin cycle press the button

until you reach the spin speed you would

like to set.

! It is possible to modify the spin speed

without pausing the machine.

! This button allows you to change the

temperature of the wash cycles.

! It is not possible to raise the temperature

over the maximum allowed for every

programme, in order to save the fabrics.

! This button allows you to pre-programme

the wash cycle to delay the start of the

cycle for up to 24 hours.

! To delay the start use the following

procedure:

- Set the required programme.

- Press the button once to activate it (h00

appears on the display) and then press

it again to set a 1 hour delay (h01

appears on the display). The pre-set

delay increases by 1 hour each time the

button is pressed, until h24 appears on

the display, at which point pressing the

button again will reset the delay start to

zero.

- Confirm by pressing the START/PAUSE

button (the light on the display starts to

flash). The countdown will begin and

when it has finished the programme will

start automatically.

! It is possible to cancel the delay start by

turning the programme selector to OFF.

If there is any break in the power supply

while the machine is operating, a special

memory stores the selected programme

and, when the power is restored, it

continues where it left OFF

The option buttons should be selected

before pressing the START/PAUSE

button.

If an option is selected that is

not compatible with the selected

programme then the option indicator

first flashes and then goes off.

SPIN SPEED button

To prevent damage to the fabrics, it is

not possible to increase the speed

over that which is automatically

suitable during the selection of the

program.

The machine is fitted with a special

electronic device, which prevents the

spin cycle should the load be

unbalanced.

This reduces the noise and vibration in

the machine and so prolongs the life of

your machine.

TEMPERATURE SELECTION button

DELAY START button

!

EN

13

! By selecting this button there is a choice

of 3 levels of wash intensity, depending

on how much the fabrics are soiled (can

be used only on some programmes as

shown in the table of programmes).

! Once the programme has been selected

the indicator light will automatically show

the wash time set for that programme.

! Selecting a different wash time the

relevant indicator will light up.

! This button allows you to add rinses at

the end of the washing cycle. The

maximum number of extra rinses is

related to the programme selected.

! This function has been studied for the

people with delicate and sensitive skin,

for which also a least residue of detergent

can cause irritations or allergies.

! It advises to also use this function for the

children items and in case of washings of

very dirty items, for which it is due to use

a lot of detergent, or in the washing of

toweling items whose fibres mostly have

the tendency to hold the detergent.

You can choose between three different

options:

- PREWASH

! This option allows you to make a prewash

and it is particularly useful for heavily

soiled loads (can be used only on some

programmes as shown in the table of

programmes).

! We recommend you use only 20% of the

recommended quantities shown on the

detergent pack.

Experiment with your chosen detergent to

find the ideal quantity.

- HYGIENE PLUS

! With this option it is possible to hygienize

the clothes, the washing programme

reach a temperature of 60°C.

- NIGHT & DAY

! This option reduces the intermediate spin

speed to 400 rpm, where applicable,

increase the water level during rinsing and

keep the laundry immersed in water after the

final rinse, in order to spread the fibre

sevenly.

! During the phase in which the water is

held in the tub, the relevant indicator light

blink to show that the machine is at a

standstill.

! Deselect the option to end the cycle with a

spin dry (which may be reduced or cancelled

using the appropriate button) and emptying

phase.

! Thanks to electronic control, the water

in the intermediate phases is emptied

silently, making this option very useful for

washing at night.

This function allows you to minimizes

creases as much as possible, eliminating

the intermediate spins or reducing the

intensity of the last one.

WASH TIME button

EXTRA RINSE button

OPTIONS button

EASY IRON button

!

14

The display’s indicator system allows you to

be constantly informed about the status of

the machine.

2

1

8109

3 4 5 6 7

1) DOOR LOCKED INDICATOR LIGHT

1

! The indicator light is illuminated when the

door is fully closed.

! When START/PAUSE is pressed on

the machine with the door closed, the

indicator will flash momentarily and then

illuminate.

! A special safety device prevents the door

from being opened immediately after the

end of the cycle. Wait for 2 minutes after

the wash cycle has finished and the

DOOR LOCKED light has gone out before

opening the door. At the end of the cycle

turn the programme selector to OFF.

2) SPIN SPEED

2

This show the spin speed of the selected

programme that can be changed or omitted

by the relevant button.

3) WASH TEMPERATURE

3

This show the washing temperature of the

selected programme that can be changed

(where allowed) by the relevant button.

4) CYCLE DURATION

4

! When a programme is selected the

display automatically shows the cycle

duration, which can vary, depending on

the options selected.

! Once the programme has started you will

be kept informed constantly of the time

remaining to the end of the wash.

! The appliance calculates the time to the

end of the selected programme based

upon a standard loading, during the cycle,

the appliance corrects the time to that

applicable to the size and composition of

the load.

Digital Display

Close the door BEFORE selecting the

START/PAUSE button.

If the door is not properly closed,

the light will continue to flash for

about 7 seconds, after which the

start command will be automatically

delete. In this case, close the door

in the proper way and press the

START/PAUSE button.

!

EN

15

5) WASH TIME

{

5

! Once the programme has been selected

the indicator light will automatically show

the wash time set for that programme.

! Selecting a different wash time the

relevant indicator will light up.

6) EXTRA RINSES

{

6

The indicator lights show the extra rinses

selected by the relevant button.

7) OPTIONS

}

7

The indicator lights show the option

that can be selected by the relevant

button (PREWASH, HYGIENE PLUS and

NIGHT & DAY).

8) WI-FI (some models only)

8

! In the models with the Wi-Fi option, the

icon indicates that the Wi-Fi system is

working.

! For all other information in the Wi-Fi

system, there is a specific manual inside

the machine.

9) DELAY START

9

This flashes when delay start has been set.

10) Kg MODE (function active only on

Cotton and Synthetics programmes)

10

! During the first minutes of the cycle, the

"Kg MODE" indicator remain on while the

intelligent sensor will weigh the laundry

and adjust the cycle time, water and

electricity consumption accordingly.

! Through every wash phase "Kg MODE"

allows to monitor information on the wash

load in the drum and in the first minutes

of the wash it:

- adjusts the amount of water required;

- determines the length of the wash cycle;

- controls rinsing according to the type of

fabric selected to be washed it;

- adjusts the rhythm of drum rotation for

the type of fabric being washed;

- recognizes the presence of lather,

increasing, if necessary, the amount of

water during rinsing;

- adjusts the spin speed according to the

load, thus avoiding any imbalance.

!

16

2

1

PROGRAM

kg

(MAX.)

TEMP.°C

DETERGENT

Recommended

Max.

2

1

All in One 20°C

4,5

20°

All Baby 60°C

4,5

60°

All in One 59 Min.

7,5

40°

Rapid 30 Min.

2,5

30°

Rapid 14 Min.

1

30°

Dark Colours

3,5

40°

( )

Auto Clean

Rinse

-

Drain & Spin

-

Shirts

1)

3,5

30°

( )

Lingerie

1)

2

40°

60°

Wool & Silk

1

30°

Delicates

2,5

40°

Mixed

1)

3,5

40°

60°

( )

Cottons

*

1)

7,5

40°

90°

( )

Table of programmes

!

EN

17

Please read these notes:

The spin speed may also be reduced, to

match any guidelines suggested on the

fabric label, or for very delicate fabrics

cancel the spin completely this option is

available with a spin speed button. This

function can be activated with the button

SPIN SPEED.

If the label does not indicate specific

information, it is possible to use the

maximum spin expected in the program.

An over dosing of detergent can cause

excessive foaming.

If the appliance detects the presence of

excessive foam, it may exclude the spinning

phase or extend the duration of the program

and increase water consumption.

( )

Only with PREWASH option

selected (programmes with

PREWASH option available).

(Only for models with liquid

detergent compartment)

When only a limited number of

articles have stains which require

treatment with liquid bleaching

agents, preliminary removal of

stain can be carried out in the

washing machine.

Pour the bleach into the liquid

bleach container, inserted into the

compartment marked "2" in the

detergent drawer, and set the

special programme RINSE.

When this phase has terminated,

turn the programme selector on

the OFF position, add the rest of

the fabrics and proceed with a

normal wash on the most suitable

programme.

1)

For the programmes shown you

can adjust the duration and

intensity of the wash using the

WASH TIME button.

* Programme tested in accordance

with AS/NZS 2040.2 with a temperature

of 40°C.

Programme also recommended for

low-temperature washes (lower than the

max. shown).

The “Cottons" programme at 40 deg.C,

1100 RPM spin is the program

recommended for a normally soiled load

at the rated capacity 7,5 kg.”

!

18

To clean different types of fabrics and

various levels of dirt, the washing machine

has specific programs to meet every need

of washing (see table of programmes).

ALL IN ONE technology

This washing machine is equipped with an

innovative system with an high pressure jet

that sprays a mixture of water and

detergent directly into the load.

The special motor movement used in this

machine manages the drum movement

during the start up of each programme, in

conjunction with the high pressure jet

spraying the detergent mixture into the load,

the cycle includes a set of spin actions that

helps the detergent solution to penetrate

into the fibers, helping dirt removal and

ensuring the best available wash

performance.

The ALL IN ONE system is also used

during the water load phases where the

high pressure jet aids the complete removal

of detergent residues trapped in the clothes

All In One 20°C

Thanks to ALL IN ONE technology, this

innovative programme, allows you to wash

fabrics such as cottons, synthetics and

mixed fabrics at 20°C with a performance

which is comparable to a 40°C wash.

The consumption of this program is about

50% of a conventional 40°C. Cottons wash.

IMPORTANT WASH PERFORMANCE

ADVICE:

! New, coloured garments should be

washed separately for at least 5 or 6

washes.

! Certain large dark items such as jeans

and towels should always be washed

separately.

! Never mix NON COLOURFAST fabrics.

All Baby 60°C

You can wash all baby clothes together, at

medium temperature, resulting in hygienic

and perfectly clean items when combined

with heavy duty soap. This is possible

thanks to the ideal pre-dose of water and

detergent, that is sprayed onto the laundry

through the jet activating the enzymes at

50°C.

All In One 59 Min.

This programme allows you to wash mixed

fabrics such as cottons, synthetics and

mixed fabrics in only 59 minutes, using the

full load of the washing machine, at 40°C

(or less) temperature. This programme is

particularly suited to slightly dirty fabrics.

Rapid 30 Min.

A complete washing cycle (wash, rinse and

spin). This programme is particularly suited

to slightly dirty cottons and mixed fabrics.

With this programme it is recommended to

use only 20% of the detergent normally

used to avoid waste.

Rapid 14 Min.

A complete washing cycle (wash, rinse and

spin). This programme is suited to slightly dirty

cottons and mixed fabrics. With this programme

it is recommended to use only 20% of the

detergent normally used to avoid waste.

Dark Colours

Program designed to mix all dark garments and to

avoid the loss of colour and the formation of creases.

We recommend the use of liquid detergent.

Auto Clean

This program is suited to clean the drum of your

appliance. It is recommended to use this

program every 50 washing cycles, to ensure a

long service life and avoid bad odors. Make sure

to start the program exclusively without laundry in

the machine, using only powder detergent for

washing machine. When the washing cycle

finishes, open the door of the washing machine

to dry the drum.

Rinse

This program performs 3 rinses with an

intermediate spin (which can be reduced or

excluded by using the appropriate button) . It

is used for rinsing any type of fabric, for

example after a wash carried out by hand.

Drain & Spin

The program completes the drain and a

maximum spin. It is possible to delete or reduce

the spin with the SPIN SPEED button.

Programmes selection

!

EN

19

Shirts

The washing cycle is optimized to reduce the

creation of creases, keeping an excellent washing

performance. It is also possible to further reduce

the spin speed, to ensure an easier ironing.

Lingerie

This program has been designed to

perfectly clean the everyday underwear: it is

particularly indicated for cottons and

resistant synthetics, with also the possibility

to mix colours (colourfast clothes only).

Wool & Silk

This programme allows a delicate washing

cycle, particularly suited to garments specified

as "Machine-Washable" Wool fabrics and

laundry items made from Silk or specified as

"Wash as Silk" on the fabric label.

Delicates

This program alternates among moments of

work during breaks and is particularly suitable

for washing delicate fabrics. The wash cycle

and rinses are carried out with a high level of

water to ensure the best performance.

Mixed

The washing and rinsing are optimized in

the rhythms of rotation of the drum and to

the water levels. The gentle spin, ensures a

reduced formation of creases in the fabric.

Cottons

This program is suitable to clean normally

soiled cotton laundry and it is the most efficient

program in terms of combined energy and

water consumptions for washing cotton laundry.

!

20

7. CUSTOMER SERVICE CENTRE AND WARRANTY

If you believe the washing machine is not working correctly, consult the quick guide

provided below with some practical tips on how to fix the most common problems.

Problem

Possible causes and practical solutions

The washing machine

does not work/start

Make sure it is correctly plugged in.

Make sure power is on.

Check whether the required program was correctly selected and to

have correctly started the machine.

Make sure the fuse has not blown and that the wall socket is working,

testing it with another appliance such as a lamp.

The porthole may not be correctly closed: open and close it again.

The washing machine

does not fill with

water

Make sure the water faucet is open.

Make sure the timer is correct set.

The washing machine

does not drain water

Make sure the filter is not clogged.

Make sure the drain hose is not bent.

Make sure there are no foreign objects in the filter.

Water leaked on the

floor near the washing

machine

This may be due to a leak in the gasket between the faucet and supply

tube; in this case, replace it and tighten the tube and faucet.

The washing machine

does not spin

This could be due to the fact that water has not been completely

drained: wait a few minutes.

Some models include a "no spin" function: make sure it is not on.

An excessive amount of detergent could prevent spin: reduce the

amount at the next wash.

Strong vibrations are

heard during spin

The washing machine may not be fully levelled: if necessary, adjust

the feet as indicated in the specific section.

Make sure transport brackets were removed.

Make sure the load is evenly distributed.

If a specific ERROR

appears of blinks

If error no. 0, 1, 5, 7 or 8 appears or blinks, contact the Customer

Service Centre directly.

If error no. 2 appears or blinks, the machine does not load water.

Make sure the water faucet is open.

If error no. 3 appears or blinks, the machine does not correctly drain.

Make sure the drain is free and that the drain hose is not bent.

If error no. 4 appears or blinks, the machine is too full. Close the

water faucet and contact the Customer Service Centre.

If error no. 9 appears or blinks, turn off the washing machine, wait 10

– 15 seconds and restart the program.

Page is loading ...

Hoover DXA 175AH/1-AUS User manual

Hoover DXA 175AH/1-AUS User manual

Related papers

Other documents