VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO
Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
INSTRUCTION MANUAL
11
11
33
33
AA
AA
mm
mm
pp
pp
EE
EE
ll
ll
ee
ee
cc
cc
tt
tt
rr
rr
ii
ii
cc
cc
PP
PP
oo
oo
ww
ww
ee
ee
rr
rr
WW
WW
aa
aa
ss
ss
hh
hh
ee
ee
rr
rr
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1-800-544-6986
IF YOU SHOULD EXPERIENCE A PROBLEM
WITH YOUR BLACK & DECKER PRODUCT,
CALL 1-800-544-6986
IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER
THE PHONE. IF YOU HAVE ASUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS
VITAL TO BLACK & DECKER.
Catalog Number PW1600, PW1750
O
I
O
I
2
3
WARNING: When using this product,
basic precautions should always be
followed, including the following:
1. Read and understand all instructions
before using the product.
2. To reduce the risk of injury, close
supervision is necessary when a product is
used near children.
3. Know how to stop this product and bleed
pressure quickly. Be thoroughly familiar with
the controls.
4. Stay alert - watch what you are doing.
5. Do not operate this product when
fatigued or under the influence of alcohol or
drugs.
6. Keep operating area clear of all persons.
7. Do not use on ladder. Loss of balance
and serious injury could result. Do not
overreach or stand on unstable support.
Keep good footing and balance at all times.
8. Follow the maintenance instructions
specified in the manual.
9. This product is provided with a Ground
Fault Circuit Interrupter (GFCI) built into the
power cord. If replacement of the plug or
cord is needed, use only identical
replacement parts.
10. WARNING: Risk of Injection or Injury.
Do Not Direct Discharge Stream at
Persons.
GENERAL SAFETY RULES
WARNING: When using this product,
basic precautions should always be
followed, including the following:
1. Always follow detergent manufacturer’s
label recommendations for proper use of
detergents. Always protect eyes, skin and
respiratory system from detergent if used.
2. Never try to stop or deflect leaks with
any body part.
3. Never put hand or fingers over the spray
tip while operating the unit.
4. Always wear safety glasses or goggles,
hearing and respiratory protection and
protective clothing when operating or
performing maintenance.
5. Always engage the trigger safety latch in
the safe position when spraying is stopped
even if only for a few moments.
6. Keep clear of nozzle. Never direct high
pressure spray at any person, animal or
self.
7. Do not use pressure that exceeds the
operating pressure of any of the parts
(hoses, fittings, etc.) in the pressurized
system. Never use with any other
manufacturers accessories or components.
8. Never spray flammable liquids or use
pressure washer in areas containing
combustible dust, liquids or vapors.
9. Never operate this machine in or near an
explosive environment.
10. Do not spray electrical apparatus and
wiring.
11. Never disconnect the high pressure
discharge hose from the machine while the
system is pressurized. To depressurize
machine, turn power and water supply off,
then press gun trigger 2-3 times.
12. Never permanently engage the trigger
mechanism on the gun.
13. Never operate the machine without all
components properly connected to the
machine (handle, gun/wand assembly,
nozzle, etc.).
14. Always turn water supply “on” before
turning pressure washer “on” unless
draining for storage. Running pump dry
causes serious damage.
15. Do not operate the pressure washer
with the inlet water filter removed. Keep
filter clear of debris and sediment.
16. Never operate pressure washer with
broken or missing parts. Check equipment
regularly and repair or replace worn or
damaged parts immediately.
17. Use only the nozzles, parts and
accessories supplied with this machine.
18. Never leave the wand unattended while
the machine is running or switched on.
19. Always hold gun and wand firmly when
starting and operating the machine.
20. Discharge residual pressure by
pressing the trigger until no more water
comes out of the nozzle.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: Wear appropriate hearing
protection during use. Under some
conditions and duration of use, noise from
this product may contribute to hearing loss.
WARNING: This product contains
chemicals, including lead, known to the
state of California to cause cancer, and
birth defects or other reproductive harm.
Wash hands after handling.
GROUNDING INSTRUCTIONS
This product must be grounded. If it should
malfunction or break down, grounding
provides a path of least resistance for
electric current to reduce the risk of electric
shock. This product is equipped with a cord
having an equipment-grounding conductor
and a grounding plug. The plug must be
plugged into an appropriate outlet that is
properly installed and grounded in
accordance with all local codes and
ordinances.
DANGER: Improper connection of the
equipment-grounding conductor can result
in a risk of electrocution. Check with a
qualified electrician or service personnel if
you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug
provided with the product - if it will not fit
the outlet, have a proper outlet installed by
a qualified electrician. Do not use any type
of adapter with this product.
WARNING: To reduce the risk of
electrocution, keep all connections dry and
off the ground. Do not touch plug with wet
hands.
GROUND FAULT CIRCUIT
INTERRUPTER PROTECTION
This pressure washer is provided with a
Ground Fault Circuit Interrupter (GFCI) built
into the power supply cord. This device
provides additional protection from the risk
of electrical shock. Should replacement of
the plug or cord become necessary, use
only identical replacement parts that
include GFCI protection. See Figure 13 for
testing procedure.
WARNING: Connect directly to outlet.
Do not use with extension cord. The use
of an extension cord will override the
GFCI built into the plug of the power
supply cord resulting in the risk of
electrical shock.
• The label on your tool may include the
following symbols.
V..............volts
A..............amperes
Hz............hertz
W ............watts
min ..........minutes
............alternating current
........direct current
no ............no load speed
............Class II Construction
…/min......revolutions or reciprocation
per minute
............earthing terminal
............safety alert symbol
SAVE THESE INSTRUCTIONS
Upper Cord Wrap Hook Assembly - PW1600
Insert cord wrap top hook (M) into the rear
slot in handle (K), pushing down firmly until it
stops. Drive two 1 1/2” self tapping screws
included in cord hook bag through handle
holes into cord wrap hook as shown until
tight. DO NOT over tighten.
PW1750 ASSEMBLY:
Tools Required:
Philips screwdriver
Adjustable wrench
Hardware Bag Contents:
- 2 pcs. flat washers
- 2 pcs. hex locking nuts
Wheel Assembly - PW1750
Remove the 2 protective plastic end caps
from axle and discard. Place wheel (E) with 5
raised square bumps facing outwards as
shown below over threaded axle end,
followed by flat washer, and hex locking nut.
Using wrench, tighten nut securely. Align 5
square knotches in wheel cap (E1) to raised
PW1600
1
3
4
2
“UP”
Label
UNIT ASSEMBLY
PW1600 ASSEMBLY:
Tools Required:
Philips screwdriver
Adjustable wrench
Hardware Bag Contents:
- 2 pcs. flat washers
- 2 pcs. hex locking nuts
- 6 pcs. 5/8” screws
Wheel Assembly - PW1600
Remove the 2 protective plastic end caps
from axle and discard. Place wheel (E), flat
washer, and hex locking nut over axle end
as shown with smooth face of wheel having
circular holes only facing outwards (side of
wheel with raised spokes faces inwards
toward pressure washer body). Using a
wrench, tighten nut securely. Align wheel
cap (E1) over wheel face as shown and
press center of wheel cap until it snaps
securely to wheel.
Handle Assembly - PW1600
1.) With rectangular steel tube (N) ends
pointing upwards as labeled, push tubes
down firmly into rectangular holes in black
top housing (P) until they hit bottom.
2.) Drive one 5/8” screw through the hole in
each side of the orange housing (Q) as
shown and into the tapped hole of the tube
until tight.
3.) Next drive one 5/8” screw through each
hole in the upper back side of the black top
housing (P) as shown into the tapped hole
of the tube until tight.
4.) You are now ready to align the
rectangular holes in bottom of handle (K)
over the tubes, pushing the handle down
until it’s bottom edge slides into black
housing (P) fully. Drive one 5/8” screw
through each hole in the back of the handle
(K) as shown into the tubes until tight to
complete handle assembly.
4
A. High pressure water outlet (OUTLET)
B. Pump Quick Connector
C. High pressure turbo wand
D. Adjustable fan wand
E. Wheels
E1. Wheel Cap
F. Gun
F1. High pressure hose connector
F2. Gun safety catch
G. Power supply cord with GFCI
H. Hardware bag
I. On/off switch
J. Garden hose Quick Connector
K. Handle
L. Removable detergent tank with cap
M. Cord wrap top hook
N. Steel Support tubes
O. Nozzle Cleaning tool
P. Black top housing
Q. Orange main housing
F
F1
F2
H
O
I
I
K
L
J
M
N
O
B
E1
E
D
P
Q
C
O
I
E1
F
F1
F2
I
K
L
J
H
M
O
D
C
E
G
N
Q
A
P
B
PW1600
PW1750
5
2
1
PW1600
3
PW1600
IMPORTANT: The outer brass ring on the
garden hose quick connector MUST be
pulled back fully as shown in Fig. 11b)
before pushing it over the pump quick
connector (B). Water will not flow through
to the pump if these 2 connectors are not
fully coupled.
Figure 12 - Connect other end of garden
hose to the cold water source and turn
water on full. This pressure washer is not
intended to pump hot water. Never connect
it to a hot water supply as it will significantly
reduce the life of the pump.
OPERATION
NOTE: Before cleaning any surface, an
inconspicuous area should be cleaned to
test spray pattern and distance for
maximum cleaning results. If painted
surfaces are peeling or chipping, use
extreme caution as pressure washer may
remove the loose paint from the surface.
This Pressure Washer is equipped with
automatic delivery flow cut-off:
When the trigger is released, the dynamic
pressure automatically stops the motor.
When the trigger is pressed, the internal
pressure drop automatically starts the
motor and the spray pressure is restored
with a very slight delay.
Figure 13 - Ensure the on/off switch (I) is in
the off position before plugging in the unit.
Depress the switch portion marked “O” to
ensure unit is off. Plug the Ground Fault
Circuit Interrupter (GFCI) (G) into a power
outlet. Indicator should turn red. T
EST
BEFORE EACH USE. Press the “TEST”
button. Red indicator should disappear.
Press “RESET” button again for use. Do
not use if above test fails.
Figure 14 - Before each use, ensure the
gun safety catch is released by pushing it
down as shown, then press the trigger for a
few seconds to allow air to escape and to
discharge residual pressure in the hoses.
Figure 15 - Turn on the pressure washer by
depressing the bottom half of the switch (I)
marked “I”. The unit will run for a few
seconds as it builds up pressure, then will
shut off. It will run on demand as the gun
trigger is depressed. Turn off the pressure
washer by depressing the upper half of the
switch marked “0”.
YOUR PRESSURE WASHER IS NOW
READY TO USE - PLEASE REVIEW THE
FOLLOWING FOR DETAILS ON
ACCESSORIES APPLICATION.
SET-UP / ADJUSTMENT
Figure 7 - Insert the fan wand (D) into the
gun wand (F) by pushing and rotating until
the two parts are locked as shown in
Figure 7.
Figure 8 - Connect the high pressure hose
(F1) to the water (OUTLET) (A) on the unit
by first inserting the brass end of the hose
into the threaded outlet on the front of the
unit, then snugly threading on the hose
coupling.
Figure 9 - Connect the garden hose quick
connector (J) to your garden hose as shown
in Fig. 9. The intake water temperature
must NOT exceed 50°C (122°F). The water
supply pressure must be between
20 and 80 psi.
CAUTION: The pressure washer must
only be used with clean water; use of
unfiltered water or corrosive chemicals will
damage the pressure washer.
Figure 10 - With the quick connector (J)
attached to your garden hose, pull back on
its outer ring and push firmly onto the
mating pump quick connector (B), (already
attached to the pressure washer inlet), then
release ring to engage.
bumps of wheel as shown and press center
of wheel cap until it snaps securely to
wheel.
Handle Assembly - PW1750
Align and begin to push tubes of handle (K)
down inside lower tubes (N) as shown.
Press spring buttons (R) of handle (K)
inward as handle tubes are pushed down
fully into lower tubes (N), and both spring
buttons protrude out through holes in lower
tube (N) completing assembly.
Upper Cord Wrap Hook Assembly - PW1750
Insert cord wrap top hook (M) into the rear
slots in handle (K) by pushing upward and
inward to snap in place. Drive two 1/2” self
tapping screws included in cord hook bag
through cord wrap holes into handle as
shown until tight. DO NOT over tighten.
6
High pressure hose
7
O
I
6
7
8
9
10
12
15
13
14
11
a)
b)
Pump Quick
Connector
O
I
PW1750
R
4
PW1750
PW1750
5
5.) Apply detergent as directed by the
detergent manufacturer.
6.) To rinse, put the on-off switch in the “off”
(0) position before pushing the adjustable
fan wand nozzle inwards as shown in
Figure 24. This will increase water pressure
and automatically stop detergent flow.
Return on-off switch to “on” (I) position.
7.) Rinse detergent from surface.
8.) When you have finished using the
detergent dispensing system, or when
changing from one detergent type to
another, you must ensure the entire system
has been rinsed clean. To do this, remove
tank to empty remaining detergent, and rinse
tank out several times with clean water.
Then fill detergent tank with clean water and
replace into pressure washer. Leaving the
nozzle in the outward detergent pick up
position as shown in figure 23, press the gun
trigger for 1 minute until only clean water is
sprayed. Remove tank and empty remaining
water. NOTE: Failure to follow the above
detergent rinsing procedure will cause the
dispensing system to become clogged.
NOTE: DO NOT USE:
• Bleach, chlorine products and other
corrosive chemicals.
• Liquids containing solvents (i.e., paint
thinners, gasoline, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the unit and will
damage the surface being cleaned.
SURFACE PREPARATION
Before starting any cleaning task it is
important to inspect the area for objects
which could create a hazard. Remove
objects from the area which could be tripped
over such as children’s toys or outdoor
3.) To remove, push turbo wand into gun
wand and twist as shown in Figure 20.
• DETERGENT
DISPENSER
Follow detergent manufacturer’s label
directions for mixing correct concentrations
of soap and detergents.
To use the detergent dispenser:
1.) Pull locking tab upwards as shown in
Fig. 21 and pull tank out of unit.
2.) Lift up to remove cap as shown in
Figure 22, fill tank with detergent and
replace cap. Reinsert tank fully into unit
until locking tab snaps into place.
3.) Insert the adjustable fan wand into gun.
Detergent applicator will only work with
adjustable fan wand.
4.) With the on-off switch in “off” (O)
position, pull the adjustable fan wand
nozzle outwards as shown in Figure 23 to
allow detergent pick up. Put on-off switch in
“on” (I) position.
ACCESSORIES
CAUTION: Before changing
accessories, adjusting pressure, or
engaging detergent draw system, switch
the unit off, pull trigger to release
pressure, and activate gun safety catch.
• ADJUST
ABLE FAN WAND
1.) Insert the fan wand (D) into the gun
wand (F) by pushing and rotating until the
two parts are locked as shown in Figure 16.
2.) To obtain maximum pressure, rotate the
fan wand nozzle in a clockwise direction as
shown in Figure 17. This narrow stream
results in deeper cleaning in a concentrated
area. For a wider fan pattern rotate the fan
wand nozzle in the counterclockwise
direction. The wider fan pattern reduces
the risk of surface damage and allows for
cleaning large surface areas quickly.
3.) To remove, push fan wand into gun
wand and twist as shown in Figure 18.
• TURBO
NOZZLE
1.) Insert the turbo nozzle wand (C) into the
gun wand (F) by pushing and rotating until
the two parts are locked as shown in
Figure 19.
8
O
I
9
furniture. Insure that all doors and windows
are closed tight. Also make sure that all
plants and trees in the adjacent area are
protected by a drop cloth ensuring that they
will not be harmed by any over spray.
RELOCATING UNIT
1.) To move unit to another location during
cleaning, switch off unit before moving it.
2.) Place power cord and garden hose into
retaining clips as shown in Figures 25 & 26.
3.) Place hand on upper handle and prop
foot against base of unit as shown in
Fig. 27 and tilt the unit backwards.
4.) Pull unit to desired location.
5.) Remove garden hose and power cord
from retaining clips.
6.) Switch unit on to continue use.
25
16
20
23
19
17
18
21
22
24
26
27
4. Disconnect the garden hose from the
water inlet.
5. Without garden hose connected to unit,
turn unit on for a few seconds and squeeze
gun trigger until water spray stops. Turn off
switch immediately.
6. Remove any remaining fluid from
detergent tank.
7. Wrap power cord on rear of unit, clipping
plug onto cord as shown in Figure 30.
8. Disconnect the high pressure hose from
the high pressure outlet and drain hose by
pressing gun trigger.
9. Engage the gun safety catch.
10. Wrap high pressure hose on front of
unit as shown in Fig. 31.
IMPORTANT: Store pressure washer
indoors away from areas that might freeze
to avoid seriously damaging the pump.
GENERAL CLEANING TIPS
• Remove the fan wand (D) from the gun
wand (F) as shown in Figure 28.
• Clean the nozzle with the cleaning tool (O).
Remove any dirt from the fan wand nozzle
hole as shown in Figure 29 and rinse.
• For cleaning tasks such as deck or brick
patio cleaning, limit your work area to
approximately 25 square feet at a time.
• Pre-rinse cleaning area with fresh water.
• Use only detergents formulated for
pressure washers.
• Always test detergent in an inconspicuous
area before use.
• Begin with a wide fan nozzle spray and
adjust the pressure to the desired spray
pattern.
• The best angle for spraying water against
a cleaning surface is 45 degrees. Spraying
head on tends to cause dirt particles to
imbed in the surface. When working on
vertical surfaces, it is best to apply
detergent starting at the bottom and working
upwards which will prevent the detergent
from sliding down and causing streaks.
SHUTDOWN / STORAGE
1. Ensure detergent tank and dispensing
system has been thoroughly rinsed as
described on page 9, and empty tank has
been replaced in unit. To empty remaining
water from detergent system put on-off
switch in “on” (I) position, and with nozzle in
outward detergent pick up position, press
gun trigger for 30 seconds. Water from the
pump will still be sprayed at low pressure
after 30 seconds, but detergent system will
be purged.
2. Put the on-off switch in “off” (O) position
and unplug the cord from the outlet.
3. Turn off water at the faucet.
O
I
31
30
11
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
See ‘Tools-Electric’
– Yellow Pages –
for Service & Sales
TECHNICAL INFORMATION
Operating pressure – 1250/1300psi
Maximum pressure* - 1600/1700psi
1. Maximum Water Flow rate* - 1.6gpm
2. Electrical requirements – 120V,
15amps, 60hz
3. Electrical cord – 35ft
4. High pressure hose – 25ft
5. Minimum amperage source –
15amps
6. Pressure of inlet water –
20 to 80 psi
7. Inlet water – Cold water only
8. Chemical injection rate 0.1 gpm
*Water flow and Max. pressure ratings
determined in accordance with PWMA
standard PW101.
29
MAINTENANCE
Clean the nozzle with the tool provided.
Remove any dirt from the spray wand
nozzle hole as shown in Figure 29 and
rinse.
Use only mild soap and damp cloth to clean
the tool. CAUTION: Never use the
pressure washer to clean itself.
IMPORTANT: To assure product SAFETY
and RELIABILITY, repairs, maintenance and
adjustment should be performed by
authorized service centers or other qualified
service personnel, always using identical
replacement parts.
ACCESSORIES
WARNING: The use of any accessory
not recommended for use with this pressure
washer could be hazardous.
SERVICE INFORMATION
Do not return this product to your
retailer. Black & Decker offers a full
network of company-owned and authorized
service locations throughout North America.
All Black & Decker Service Centers are
staffed with trained personnel to provide
customers with efficient and reliable power
tool service.
Whether you need technical advice, repair,
or genuine factory replacement parts,
contact the Black & Decker location nearest
you.
To find your local service location, refer to
the yellow page directory under “Tools—
Electric” or call: 1-800-544-6986.
TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this
product for two years against any defects in
material or workmanship. The defective
product will be replaced or repaired at no
charge. Do not return this product to
your retailer.
Take or send the product (prepaid) to a
Black & Decker owned or authorized
Service Center for repair or replacement at
our option. Proof of purchase may be
required. Black & Decker owned and
authorized Service Centers are listed under
“Tools-Electric” in the yellow pages of the
phone directory.
This warranty does not apply to
accessories. This warranty gives you
specific legal rights and you may have
other rights which vary from state to state
and province to province. Should you have
any questions, contact the manager of your
nearest Black & Decker Service Center.
This product is not intended for commercial
use.
Free Warning Label Replacement: If your
warning labels become illegible or are
missing, call 1-800-544-6986 for a free
replacement.
28
10
Unit not plugged in.
On/Off switch is in the Off
position.
Gun trigger not being
squeezed.
GFCI tripped.
Water faucet not fully
turned on.
Water inlet filter clogged.
Nozzle worn.
Pump is sucking air.
Water supply restricted.
Not enough inlet water
supply.
Pump is sucking air.
Water inlet filter clogged.
Discharge nozzle is
obstructed.
Adjustable fan wand nozzle
tip is not pulled forward.
Turbo wand is installed.
Detergent container is
empty.
Detergent is too thick.
Filter on detergent suction
tube is clogged.
Discharge nozzle is
obstructed.
Loose fittings.
Missing/worn rubber
washer.
Plug in power cord.
Turn switch to the “On” position.
Squeeze gun trigger with switch in
“ON” position.
Press reset button at GFCI on plug
end of cord.
Open water faucet fully.
Remove filter (B1) and rinse to clean. Fig. 32
Contact B&D Customer Service
Representative at 1-800-544-6986.
Check that hoses and fittings are air
tight. Turn off machine and purge
pump by squeezing gun trigger until a
steady flow of water emerges from the
nozzle.
Check garden hose for kinks, leaks
and blockage.
Turn water on full force - check garden
hose for leaks and kinks.
Check that hoses and fittings are air
tight. Turn off machine and purge
pump by squeezing gun trigger until a
steady flow of water emerges from the
nozzle.
Remove filter (B1) and rinse to clean.
Fig. 32
Remove debris as shown in Fig. 29
with tool provided.
Pull nozzle tip forward.
Remove turbo wand. Install adjustable
fan wand and pull nozzle tip forward.
Add more detergent.
Use detergent recommended for use
in pressure washers only.
Fill tank with warm water and allow
filter to soak. Empty and fill tank with
clean water several times to rinse out
filter.
Remove debris as shown in Fig. 29
with tool provided.
Tighten fittings.
Replace washer in hose adapter.
Motor does not start.
Unit does not reach
high pressure.
Output pressure
varies high/low.
No detergent.
.
Garden hose
connection leaks.
12
TROUBLESHOOTING GUIDE
Symptom Cause Solution
32
Spray wand not properly
attached.
Broken O-ring.
Pump is sucking air.
Loose fittings.
Water seals are damaged
or worn.
Oil seals are damaged or
worn.
Supply voltage below
minimum.
System has residual
pressure.
Voltage loss due to
extension cord.
Cleaner not used for long
periods.
Insert the spray wand into the wand
extension. Push in and turn to lock
spray wand into place.
Contact B&D Customer Service
Representative at 1-800-544-6986.
Check that hoses and fittings are air
tight. Turn off machine and purge
pump by squeezing trigger gun until a
steady flow of water emerges from the
nozzle.
Check that all fittings are tight.
Contact B&D Customer Service
Representative at 1-800-544-6986.
Contact B&D Customer Service
Representative at 1-800-544-6986.
Verify that ONLY the pressure washer
is running on this circuit.
Turn unit off, squeeze gun trigger to
release pressure, then turn unit on.
Do not use extension cord with this
unit - plug directly into outlet.
Contact B&D Customer Service
Representative at 1-800-544-6986.
Spray wand or
extension leaks.
Pump is
excessively noisy.
Water leaks from
pump.
Oil leak.
Motor buzzes but
fails to run.
TROUBLESHOOTING GUIDE - continued
Symptom Cause Solution
13
B
B1
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
